Question about Toyota Cars & Trucks

Open Question

Fixing slave cylinder on a 1977 toyota truck

Adjusting a slave cylinder

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Replaced slave cylinder on 1988 Chevy truck dosen't work.

try to do this http://www.youtube.com/watch?v=uj1dMdYgRK4 this might work for you let me know if it does

Posted on Apr 09, 2009

  • 225 Answers

SOURCE: 86 ford mustang 5.0 ho motor. just installed a

some of the mustangs have an self adjusting cable, ran into this problem once. sorry i can't remember how to adjust it. think you have to pump the pedal a bunch of times. hope this help some.

Posted on Aug 12, 2009

  • 474 Answers

SOURCE: My 2000 Toyota Tacoma 2.7 liter 4 cylinder truck

sounds like its time for a new clutch

Posted on Oct 31, 2009

  • 6982 Answers

SOURCE: new clutch not working properly really could use some help

My best guess on this, assuming that the clutch master is working and it has no air remaining in the system is that you either have the wrong throwout bearing in there or that it is installed incorrectly. Also, rare but can happen is that if the pressure plate assembly is a rebuilt one, the face has been cut too far and clearances are off.
Obviously, check everything external before taking it apart again, but that's where I think you will need to go.

Posted on Nov 18, 2009

Testimonial: "thanks did have some issues installing throw out bearing so maybe that is my problem"

  • 432 Answers

SOURCE: My 1993 GMC truck does not have much clutch. Is

Hydraulic clutch will only go so far.No way that I know of to make it go farther .I guess you could try making a little extention to your rod end to make it longer.

Posted on Jan 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Does Toyota hilux R150 gear box have a clutch adjustment ?ie master cylinder adjustment ?


If it is adjustable it will have a threaded push rod at the slave cyl ,bleed the hydraulic system first adult the clutch then bleed again .

Oct 26, 2015 | Toyota Cars & Trucks

2 Answers

How do you bleed a hydraulic clutch on a 1977 corvette


you bleed like you would the brake system. there is a bleeder screw on the slave cylinder that you bleed the system.

Oct 11, 2014 | 1977 Chevrolet Corvette

1 Answer

1994 toyota pickup


No, this is a hydraulic clutch and the only adjustment may b on the pedal linkage for free travel to the master cylinder. It sounds as though you may have a bad clutch master cylinder or defective slave cylinder.

Apr 26, 2014 | 1994 Toyota Pickup

1 Answer

Slipping Clutch on Toyota Townace 1988 Van.


Check that the slave cylinder is fully releasing the clutch (push the clutch fork and shaft all the away back into slave cyl.. If ok replace the clutch assy.

Mar 29, 2013 | Toyota Cars & Trucks

1 Answer

How to adjust the clutch on 1977 mgb. my clucth is almost on the floor to change gears


There should be just a couple thousands of an inch of free play at the slave cylinder to the fork. (at the bell housing) If you have more than that, then adjust the length of the slave cylinder pin. Your symptoms can also be caused by not enough brake fluid in the clutch master or air in the line. If it gets way better by pumping the pedal you might just need to bleed the air out. If it is leaking fluid at the slave, it needs a new rubber washer inside - a rebuild kit usually includes the dust boot for it also. If it is leaking fluid at the master, rebuild that.

Oct 15, 2011 | Cars & Trucks

1 Answer

The clutch will not engage properly on my 1988 toyota pickup. Already replace clutch master cyclinder and clutch slave?


There are a couple of possibilities; worn clutch plate, failed pressure plate, possible hanging up of the throw-out bearing. Also, some hydraulic clutches have a throw adjustment on the slave cylinder that may need adjustment after replacing the slave cylinder.
If you plan on more DIY maintenance, I would highly recommend buying a Haynes service manual, you'll find the $25 well-spent:
Toyota pickup manual

Mar 31, 2011 | 1988 Toyota Pickup

2 Answers

Having problems with the clutch in my 1998 Ford Ranger. There is no freeplay, and it is very difficult to shift. Do I need to adjust the clutch? If so, how do I adjust it?


The clutch is not adjustable,it is a fluid clutch.It has to be a leak,or the slave cylinder,and,or, the master cylinder are bad,It does not have to be leaking to be bad,but it is one of the two.Rate please,thank you.

Jul 12, 2010 | 1998 Ford Ranger SuperCab

1 Answer

How do i adjust my cluth on a 2003 tacoma


The slave cylinder in these trucks makes the clutch non adjustable. If you have a soft clutch pedal which goes to the floor and can not shift as easy as it used to the slave cylinder is low on fluid or weak. Check the reservoir of the slave cylinder to see if its full. If low fill it with the recommended Power Steering fluid which is DOT3 approved I do beleive and pump the clutch pedal about 25 times with the engine off. The clutch should operate correctly. If it tends to get worse the slave cylinder needs to be replaced

Jul 11, 2010 | 2003 Toyota Tacoma

1 Answer

New rear brake shoes on toyota starlet one side sticking on red hot?


Sounds like it was not installed correctly.
The slave cylinder may need replaced.
The linkage and springs that are part of the brake system may need checked for proper hookup.
The shoes my have been adjusted too tight on installation.

I would hedge my bets on a bad slave cylinder if it wasnt replaced.

Apr 07, 2010 | 1984 Toyota Starlet

1 Answer

My clutch disengages too low. Can I adjust it to disengage higher up (from the floor)?


no, its wearing out or your slave cylinder is defective. Get it looked at ASAP. If its a slave cylinder it can be good one push and nothing the next.

Nov 21, 2009 | 2001 Toyota Echo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...