Question about 2000 Isuzu Rodeo

Open Question

Torque specs for flywheel 2000 isuzu rodeo - 2000 Isuzu Rodeo

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

Ad
emissionwiz
  • 76109 Answers

SOURCE: i need torque specs for 94 rodeo

flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Posted on Feb 14, 2009

mx5turbo92
  • 545 Answers

SOURCE: i'm looking for the 2000 isuzu rodeo 3.2L v6 connecting rod bearings torque specs.

1. Check the connecting rod alignment If either the bend or the twist exceeds the specified limit,the connecting rod must be replaced. Bend per 100 mm (3.937 inch) Limit: 0.15 (0.0059) Twist per 100 mm (3.937 inch) Limit: 0.20 (0.0078)

2. Measure the connecting rod thrust clearance. Use a feeler gauge to measure the thrust clearance at the large end of the connecting rod If the clearance exceeds the specified limit, the connecting rod must be replaced. Standard: 0.16 mm - 0.35 mm (0.0063 inch - 0.0138 inch) Limit: 0.40 mm (0.0157 inch)

3. Measure the oil clearance between the connecting rod and the crankshaft.

    1. Remove the connecting rod cap nuts and the rod caps (12). Arrange the removed rod caps in the cylinder number order.
    2. Clean the rod bearings and the crankshaft pins.
      1. Carefully check the rod bearings. If even one bearing is found to be damaged or badly worn, the entire bearing assembly must be replaced as a set. Reinstall the bearings in their original positions. Apply plastigage to the crank pin.
      2. Reinstall the rod caps (12) to their original positions. Tighten the rod cap nuts. Torque: 54 Nm (40 ft. lbs.) Note: Do not allow the crankshaft to rotate.
      3. Remove the rod caps.
        1. Measure the width of the plastigage and determine the oil clearance. If the oil clearance exceeds the limit, replace the rod bearing as a set. Standard: 0.019 mm - 0.043 mm (0.0007 inch - 0.0017 inch) Limit: 0.08 mm (0.003 inch)
        2. Clean the plastigage from the bearings and the crankshaft pins.

Posted on Jun 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque specs for a 1996 isuzu fuego gearbox and flywheel


What is the torque specs for 1996 isuzu fuego gearbox and flywheel

Sep 08, 2016 | Isuzu Cars & Trucks

1 Answer

? looking the bolt tension specs for flywheel and clutch pressure plate for 4hf1 thank you


Torque Specification - National Truck Spares ' Parts

www.nationaltruckspares.com.au/Parts.aspx?ProductTypeID=8...
1073, 4BC2 tq, Isuzu, Torque Specification, KT26 TLD57 NKR57 NPR57 ... 1075, 4HF1Tq, Isuzu, Torque Specification, NKR66 NPR66, 92 - 03, 4HF1, 4334

Small Block Chevrolet V8 Engine Specs ' Torque Specs ...

boxwrench.net/specs/chevy_sb.htm
Flywheel (Clutch). Thread Locker, 60 ft-lbs. Clutch Pressure Plate, Thread Locker, 35 ft-lbs. Centerbolt. (Harmonic Damper). Engine Oil, 60 ft-lbs. Bellhousin

Nov 07, 2015 | Cars & Trucks

1 Answer

I have 2000 issue rodeo flywheel cracked around center driving bolt are still in flywheel outside of flywheel completely separated what would cause this


too much vibration/stress on the flex plate.

many different things could have caused it,
incorrect torque on the flywheel bolts...
bad thrust bearing in transmission...
up to "you got the one lucky flexplate" that had stress fractures during manufacturing.

Sep 25, 2014 | 2000 Isuzu Rodeo

1 Answer

Need torque specs for isuzu rodeo 3.2 intake manifold


josephrloop,

Go to: http://www.autozone.com/autozone/ymme/ymmeYear.jsp?_requestid=552857

Here you can select the year, make and model.

I hope this information proves useful and helps you with your intake torque success.

Cordially,

carsandcomps
Guru @ Fixya

Apr 10, 2010 | 2000 Isuzu Rodeo

1 Answer

I need torque specs for 94 rodeo


flywheel 80-90 foot lbs (new bolts 90), press plate 45 foot lbs

Feb 14, 2009 | 1995 Isuzu Rodeo

1 Answer

What is the 98 isuzu rodeo head bolt torque


joyce, there are different specs for sohc and dohc engines. my advice is to get a Haynes manual from the auto parts store.

doug

Aug 30, 2008 | 1998 Isuzu Rodeo

1 Answer

Torque spec for flywheel bolt: Isuzu 2.5 diesel engine


normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Jul 27, 2008 | 1995 Isuzu Pickup

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...