Question about 2008 Chrysler Town & Country
All courtesy lights stopped working, including dome lights, lighted mirrors and the dome halo light. Replaced fuse but it keeps recurring.
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
if it is covered by a white plastic then inspect it carefully and look for slots where you can put tiny screwdrivers to pry the plastics off, then you can replace your bulb. just be careful not to break the plastic.
tnx 4 using fixya,
Posted on Sep 14, 2008
I work for a brake repair shop and trust me you are not alone.Enterprise and alot of other people bought the same van and had the same trouble.I hate to say but it doesnt stop there.About every 14 to 15 thousand miles you have to replace the front pads.As of now they dont have an upgrade,for instance ceramic pads, but I am sure they will very soon
Posted on May 01, 2009
2008 Chrysler Town and Country
Replacing the Rear Brake Pads
Process is typical except for the rotating (screw type) brake piston. You cannot just compress the brake piston with a C-clamp, you have to turn the piston back in. This is easily done with the correct tool (Rear Disc Brake Piston Tool). The tool I had needed to be slightly modified to fit Chrysler's pattern.
Most Auto Parts store like Auto Zone and Parts Source will have the tools for lone or you can buy the tool and keep it in your tool box and the price ranges from $12.00 to $50.00 depending on the brake tool as to universal or specific to the vehicle make. Good luck and keep me posted.
Posted on Nov 08, 2009
If you're lucky, on the inside of the door, will be a triangular panel
right behind the mirror that you can pop off. If you're not as lucky
and it's one piece or the panel is blocked by the door panel, you'll
need to remove the door panel to change it.
On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can remove the bolts holding the mirror onto the door
Posted on Nov 09, 2009
Memory selector is on driver's door, First set driver 1 seat and mirror positions, then press and release memory "s" button. then press and release memory selector "1" button. repeat for # 2 driver substituting memory selector 2 in step 2. hope this will help you
Posted on Jan 26, 2010
Testimonial: "Thanks so much . Your advice was spot on."
Tips for a great answer:
Jan 14, 2016 | Chrysler Cars & Trucks
Dec 21, 2015 | Cars & Trucks
Dec 16, 2015 | 2004 Chrysler Town and Country
Feb 11, 2015 | 1989 Lincoln Town Car
Aug 21, 2013 | 1996 Mercury Cougar XR7
Aug 11, 2017 | 2005 Chrysler Town and Country
Jul 01, 2017 | 2000 Chevrolet Monte Carlo
Mar 15, 2010 | Buick Regal Cars & Trucks
Jun 24, 2009 | 1999 Chrysler Town & Country
67 people viewed this question
Usually answered in minutes!