Question about Cars & Trucks

Open Question

Trying to locate the coolant temperature sensor on a 1989 Mazda B2200

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 120 Answers

SOURCE: location of the coolant temperature sensor

in the top of the intake very small hard to see

Posted on Feb 13, 2009

  • 155 Answers

SOURCE: How do I change the temperature sensor under the

It’s located on the driver’s side of the engine on top /side of the head.. midway.. I don’t think you need to remove the engine cover to see it.. if it is the correct one it will have a dark green top.. the bad version has a black top… but they can all go out to lunch on you if old enough.

To replace.. make sure the car is cool..
You need a hood tool.. or small pair of pliers to remove the retaining clip that holds it in place.
Place a rag under and around it to catch the coolant.. you will lose less than a half a cup.. if that.

Pull the retaining clip back toward you.. try not to drop it.. (another good reason for the rag)

Wiggle the sensor.. pop it out.. and replace with the new green top one make sure you clean the area well.. and when you reinstall the new one that the c clip goes back on straight or it will leak.

Once you see the part out of the box.. you will understand how it works

Start the car.. check for leaks.. run until warm with the heater on.. top up the coolant overflow bottle with distilled water.. (if more than a half a cup.. you should mix the proper anti freeze and distilled water and then top up with that)

Good luck

Posted on May 06, 2009

  • 119 Answers

SOURCE: replacement of coolant temperature sensor

located under intake in water crossover pipe,you can access the sensor by removing intake chamber box,then pcv hose connected to the block,the connector is orangeish 2pin,use a 19mmdeep socket on a 3/8 ratchet to get it loose,make sure engine is cool,also make sure there is a new brass washer with your new sensor,sometimes the old washer comes off when removing the sensor,sometimes it sticks to the pipe,some coolant will escape so make sure to top it off

Posted on Jul 14, 2009

  • 521 Answers

SOURCE: Coolant Temperature Sensor location on 2006 impala

driver side of the engine block, forward and above the transmission. This piece threads into the engine block.

Posted on Jul 22, 2009

  • 169 Answers

SOURCE: sensor locations

air intake look at snorkel it could be part of mass air flow check intake for eng coolant

Posted on Aug 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1989 Nissan sentra 3 door hatch. The temperature gauge is reading cold all the time and the needle does not move. I have just replaced the thermostate (which I thought would be the fault) but no...


It can be the water temperature sensor. Sensors generally increase in resistance causing less current flow through the circuit which in turn causes less needle deflection on your temperature gauge. I have a 93 Mazda B2200 doing just that.

Jan 15, 2014 | 1989 Nissan Sentra 4 Door

1 Answer

Loation of a coolant temperature sensor on a 1989 F250 351W


COOLANT TEMPERATURE SENSOR

1989 Ford Truck F250 3/4 ton P/U 2WD 5.8L FI Windsor 8cyl

The Coolant Temperature Sensor is located: Under hood, driver side, upper engine area, rear of water outlet, mounted in intake manifold

Feb 12, 2013 | 2003 Chevrolet TrailBlazer

1 Answer

I have an 1989 mazda b2200 pickup it just started blowing fuses every time i turn on my park lights.


check tail & park light circuits for short to ground. best place to start is at trailer wiring harness. (if equiped) i might want to purchase a "short finder" tool. (fairly cheap at harbor freight.) to help locate area of short. good luck.

Oct 21, 2011 | 1988 Mazda B2200

1 Answer

Trying to locate coolant temperature sensor in 06 mazda 3


The coolant temperature sensor (ECT) is located on the coolant tube near the air filter housing, I have included a few diagrams to assist in helping you to locate this sensor. These diagrams are for the 3.0L engine.


asetech74_20.gif

asetech74_21.gif

Here is the location if this is the 2.3L engine


asetech74_22.gif

asetech74_23.gif

Sep 18, 2011 | 2006 Mazda 3

1 Answer

1989 mazda b2200. new batt. new cables, new altornater. will not hold a charge. will not charge off alt.


Sorry this isnt a solution but i am having the same problem with my mazda b2200 i replaced the alternator and now the battery will not hold a charge. Please help

Jan 26, 2011 | Mazda B2200 Cars & Trucks

1 Answer

I need a diagram of the exhaust system on a Mazda 626


0996b43f80203328.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2000 MPV

1 PCM 2 Mass air flow (MAF)/intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Fuel tank pressure sensor 5 Engine coolant temperature (ECT) sensor 6 Crankshaft position (CKP) sensor 7 Camshaft position (CMP) sensor 8 Knock sensor 9 Heated oxygen sensor (HO2S) (front, LH) 10 Heated oxygen sensor (HO2S) (front, RH) 11 Heated oxygen sensor (HO2S) (rear, LH) 12 Heated oxygen sensor (HO2S) (rear, RH) 13 EGR boost sensor 14 Power steering pressure (PSP) switch 15 Main relay


0996b43f8020330c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2001 MPV

1 PCM 2 Mass air flow (MAF)/Intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Engine coolant temperature (ECT) sensor 5 Crankshaft position (CKP) sensor 6 Camshaft position (CMP) sensor 7 Knock sensor 8 Heated oxygen sensor (HO2S) (front, LH) 9 Heated oxygen sensor (HO2S) (front, RH) 10 Heated oxygen sensor (HO2S) (rear, LH)* 11 Heated oxygen sensor (HO2S) (rear, RH)* 12 EGR boost sensor


0996b43f8020330f.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart- 2002-06 MPV

May 22, 2010 | 2004 Mazda MPV

2 Answers

1989 mazda b2200 can not set timing


i have a 1988 mazda b2200 and i was sittin still runnin and it was a lil low in water and i was just ab to take off when it cut off. it made steam *** out the hood. the thing is its gettin eletric to the plugs and its gettin gas and i even tried a lil eather and its turnin over it just want crank. do u have a idea wat it could b? im thinkin it jump timeing.

Feb 17, 2010 | 1988 Mazda B2200

1 Answer

1988 mazda b2200 a little hose is leaking from the thermostat housing to im guessing water pump. the hose is skinny n shorter than the hose from radiator to therm housing. what is this called?


This is going to be a thermostat bypass gose, which allows some coolant to bypass the thermostat while the engine is coming up to temperature.

Jan 08, 2010 | 1988 Mazda B2200

1 Answer

I need a full diagram of under the hood of a 1989 Honda Accord Lx or the diagram of where to find the Coolant Temperature Sensor


The coolant temperature sensor is located under the hood on the driver's side, upper engine area, and mounted on the rear of the cylinder head. Hope this helped and best wishes.

Sep 09, 2009 | 1989 Honda Accord 4 Door

1 Answer

1989 Mazda b2200 starts but won't stay running


My mazda b2200 starts and will stay running as long as the key is in the start position, but stops as soon as the key is turned from the start position

Feb 07, 2009 | 1989 Mazda 323

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...