Question about 1998 Chrysler Cirrus

Open Question

Where is the iat sensor on chrysler cirrus

2.5 v6 engine

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: how do I change the

I did a Google search "How do you replace the rear spark plugs on a 2000 Chrysler Cirrus?" and found this link: http://www.faqs.org/qa/qa-6243.html

I haven't tried it yet and am thinking of purchasing a Chilton manual just in case, but as far as explanations go the one at the very bottom of the page in the link sounds the most legitimate so far.

Besides, I have to pay you guys $9.99 for one answer that I can get for free; or I can get the Chilton and have a whole heap of answers for around $20.

Posted on Jul 14, 2008

Ad
fischmilch
  • 96 Answers

SOURCE: 1999 chrysler cirrus

Check the coil packs, or the Ignition module. Disconnect the harness to the ignition module. And test the leads to see if there is current. I don't know what the specs should be, but it will be minimal. Never overlook fuses either.

Posted on Nov 07, 2008

  • 148 Answers

SOURCE: how do you replace spark plugs on a 1996 chrysler

You will have to remove the upper intake manifold to replace the rear plug.There are no shortcuts ,and besure to replace the upper intake gasket as well.

Posted on Jul 28, 2009

co7196
  • 3433 Answers

SOURCE: need location of crankshaft position sensor on a

The crank sensor should be found at the front by the crank pully. it is bolted to the engine wuth a wire connection plug on it.

Posted on Sep 28, 2009

  • 366 Answers

SOURCE: check engine light

Code 12.................Problem with the battery connection. Direct battery input to PCM disconnected within the last 50 ignition key-on cycles.

either a loose connection or the battery dead or removed within 50 last times you turned on the car, check battery terminals for corrosion or loose connector, and check the earth wire for corrosion, the code will dissapear by itself if the power is not removed again

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does the book say in hours to replace the timing / water pump on a 1997 chysler cirrus 2.5 v6 ? Or in your opinion what's a fair price to have this done by private person coming to the house .


Replacing Chrysler 2.2 and 2.5 liter engine timing belts

www.allpar.com/fix/timing-belt-22.html
Replacing the timing belts on Chrysler and Dodge 2.2 and 2.5 liter ... Then loosen the bolts on the crankshaft pulley and the water pump pulley so they will be ...

HOW TO PUT WATER PUMP ON - 1997 Chrysler Cirrus

repairpal.com > Questions > Chrysler > Cirrus > 1997 Chrysler Cirrus
Jul 4, 2010 - WATER PUMP WANT HOLD WATER LONG AND NOW IS MAKING A ...If you change the water pump,you need to also change the timing belt ...

Timing belt - 1995 Chrysler Cirrus - RepairPal


Nov 24, 2015 | Cars & Trucks

1 Answer

CPS crankshaft position sensor for a 1999 Chrysler Cirrus 2.5l v6 How do u get to the sensor and what is the steps to take to get it installed It is located in the back of the back of the engine. T


Here is info on a '96 Cirrus with same 2.5L engine. Check to see if same as yours.http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528008987d

Dec 30, 2012 | Cars & Trucks

1 Answer

I have a 1995 chrysler cirrus when im at the light the car starts jerking and sometime it shuts off.


IT WOULD BE NICE IF YOU TOLD US THE ENGINE SIZE;STRAIGHT OR AUTO TRANS,AC ETC.
The 3.9 LT V6 engines back then had bad lower distributor/camshaft bushing. IF your car missfires-is hard to start-or tries to run backwards upon shutdown it may be this.
Engine will have to be put on analyzer(to show vaariable timing caused by bushing)=easy to Dx and may be covered by warranty .

Aug 23, 2012 | 1995 Chrysler Cirrus

1 Answer

Where is the distributor cap in my 2000 chrysler cirrus 2.5l V6


On the rear face of the right cylinder head. Cam sensor is built into it too. Just follow a plug wire.

May 03, 2012 | 2000 Chrysler Cirrus

1 Answer

My 1998 Chrysler Cirrus LXi 2.5L 'Suddenly stopped', (Despite second fuel-pump, distrib, cam and crank-sensors (All 'under-hood' new fuses, (Incl. 'ASD relay/s ), Still, 'Won't deliver any 'spark', RUDE!...


ok we changed the crank sincere and still don't have any spark to my plug's and everyone is telling me different things checked the fuses and the fuel pump is working . it is a 1995 Chrysler cirrus lx 2.5 V6 please help

Apr 28, 2011 | 1998 Chrysler Cirrus

1 Answer

Cannot find the coil pack on at Chrysler Cirrus 2000, trying to replace it and cannot find it on the engine


There is only one reason you would not find a coil pack on your cirrus is if it is a v6, which is built into the distributor. (VERY common problem is the distributor on those cars, well that and crankshaft sensors) Because on the 4cylinder it is on the top of the engine. The distributor is just to the left (towards passenger side) of the brake master cylinder/booster. Not a fun job but can be done without removing a lot. Hope this helps.

Sep 25, 2010 | 2000 Chrysler Cirrus

1 Answer

What is the location of the crank sensor in a 95 chrysler cirrus ??


I have a 95 Cirrus LX 2.5L V6 and had to find this, too, because I needed to replace it. (You can search the internet for images of this so you'll know what it looks like.)
This sensor is in a tough location to get to... the sensor slips into a hole on the engine block directly underneath the distributor. (I wasn't able to even see it with a flashlight from any angle -- that's why you need to know what it looks like so you can feel for it with your fingers.)
You'll have to remove the air intake housing, remove the throttle assembly and also remove the intake manifold.
It's tough to replace this sensor because of its location -- it'll try your patience but it can be done. Stick your hand down between the distributor and the master brake cylinder and feel underneath the distributor. You should feel a bolt head with a nut on it (this holds the sensor in place); near the nut should be a small electrical connector. It's on a short set of wires from the sensor. You'll need to disconnect this and remove the lock-down nut before the sensor can be pulled out of its hole in the engine block.

Aug 09, 2010 | 1995 Chrysler Cirrus

1 Answer

Need location of crankshaft position sensor on a 1996 chrysler cirrus v6 location on engine and how to find it


The crank sensor should be found at the front by the crank pully. it is bolted to the engine wuth a wire connection plug on it.

Sep 28, 2009 | 1996 Chrysler Cirrus

Not finding what you are looking for?
1998 Chrysler Cirrus Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...