Question about Hyundai Motor 2002 Sonata

Open Question

Changing wheel bearings on 2002 hyundai sonata

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 393 Answers

SOURCE: replacing rear wheel bearings on 1999 hyundai sonata

  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Posted on Nov 15, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the wheel bearing from the steering knuckle in a 2002 hyundai sonata.


Will have to be removed from the vehicle and pressed out and then back in again! Once out, bring to a shop where they can do this for you, then re install. May cost a few bucks unless you have a friend with a press.

Oct 21, 2013 | Hyundai Cars & Trucks

1 Answer

How to remove hub assembly 2006 sonata


hub has to be pressed out of the wheel bearing this is a garage job you need a hydralic press to press hub from wheel bearing.

Nov 25, 2011 | 2006 Hyundai Sonata

1 Answer

Could you please tell me the cost to replace rear left wheel bearing on 2004 Hyundai Sonata.


Rear wheel bearing should not be very much. Front would be considerably more. Find a reputable mechanic with a reasonable shop rate. STAY AWAY from car dealerships , they always , always , always overcharge.

Jan 29, 2011 | Hyundai Motor 2004 Sonata

1 Answer

How do I change the front wheel bearing in a 2001 Sonata 6 cyl


jack the front off the ground remove the tire remove the brake caliper remove the rotor remove the bolt hol;ding the front axle into the spindle hub, remove the hub and bearing.

May 06, 2010 | 2001 Hyundai Sonata

1 Answer

How to replace front wheel bearing 2009 Sonata


No way ,its a strip the the whole hub unit off and there is a circlip coming in from the back ,which is the way the bearing is pushed out ,NO HAMMERS

Oct 23, 2009 | 2006 Hyundai Sonata

1 Answer

Wheel bearing & drive axel replacement


lift the car support on jack stands remove the wheels remove the brake systems remove the wheel hub locking nut and then remove the strut (this must be compressed or it will hurt you)
remove the axles then when that is complete you need to have the wheel bearings knocked out of the brake hub or removed from the strut assembly and then a new pair reseated, or bolted on then you can assemble in reverse, if you are not mechanically inclined I would recommend a mechanic to do this.

Apr 03, 2009 | 2000 Hyundai Sonata

1 Answer

Replacing rear wheel bearings on 1999 hyundai sonata


  1. for drum brakes with sealed hub(all one piece) remove lug nuts and wheel.
  2. spray penetrating oil around studs if there is a big phillips head screw visible remove it with impact driver/if not use big ballpeen hammer ,tap on flat of drum near studs(becareful not to hit them) until drum loosens(your creating a shockwave to loosen rust)
  3. once drum is off there are 4-bolts coming in from behind backing plate, remove them then hub should be able to be removed w/a little persuation from hammer.
with out sealed hub ,
  1. remove wheel
  2. remove dust cap,cotterpin,star washer(if equipped) do not re use cotter pin
  3. remove nut then washer, wiggle brake drum and front bearing will come out.
  4. put nut on shaft tighten 2-3 turns grab drum by sides and pull towards you this should remove drum leaving inner bearing/seal on shaft
  5. to replace reverse procedure making sure to pack new bearings w/grease(take drum and use long punch to remove bearing races, use race/seal installer to install new races
with disk brakes

  1. remove wheel
  2. remove caliper/bracket
  3. remove rotor
  4. remove 4-bolts from behind,tap old hub out
  5. reverse procedure



Jul 19, 2008 | 1999 Hyundai Sonata

Not finding what you are looking for?
Hyundai Motor 2002 Sonata Logo

Related Topics:

446 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...