Question about 1997 Chevrolet Astro

Open Question

Astro van air blend door actuator - 1997 Chevrolet Astro

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
chiquititas
  • 1010 Answers

SOURCE: AC is blowing out HOT air... How to get to the Blend Door to check it?

No, you just need to fill freon gas.

Posted on Jun 25, 2008

Ad
bunnydawg
  • 5158 Answers

SOURCE: 2001 ASTRO VAN AIR CONDITIONING

i suspect the vents are controlled by vacuum and are not opening due to a vacuum leak.

Robert

Posted on Sep 01, 2008

SOURCE: 2000 Astro van - vent

The problem is a 1/8 diameter hose that runs from the front of the engine over the top and connects at the rear of engine on the drivers side. It is a vacuum hose #GM15967970 It cost about $6.22 at your GM dealer. Hope this helps Bill. My E-Mail is Uflyups@aol.com
This was posted on a problem with a 2002 astro, I do believe it is the same fix. A simple vacuum hose, It is difficult to route through the engine

Posted on Sep 01, 2008

  • 1 Answer

SOURCE: Blend door

ok first put you front seat down and back raise steering wheel . now lay on you back with you head in the drivers floor board. look up see 2 screws remove them and the panel they hold on . look to left main wire harness needs to be moved to the right , up and behind it is th blend actuator 7/32 socket to remove it then manually turn the white peg , total labor 30 min

Posted on Dec 15, 2008

  • 109 Answers

SOURCE: ned to know where the blend door actuator for the

i think it is on the air distribution box and alot of times you have to take it out to take the actuator off which requires removal of the dash

Posted on Jun 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Install heater control valve, 99 Chev astro van how to install heater control valve, 99 model


This year and model doesn't have a heater control valve it uses what is called an electrically actuated air temperature control blend door to control heated air and AC temperatures.

Feb 28, 2017 | Cars & Trucks

1 Answer

Where does vacuum go to, to operate blend door


The blend door under the dash has been electric since 1996.

Jun 25, 2013 | 2003 Chevrolet Astro

2 Answers

1997 astro van blows only lukewarm air?


sounds like your blend door is stuck in the middle of the operating range. this door directs air either fully or partially over the heater core or ac evaporator. when stuck in the middle u will alwaysd get a blend of both

Nov 17, 2012 | 1998 Chevrolet Astro

1 Answer

2002 ford e350 van. I have no air coming through the rear vents but the blower motor is working great.


Sounds like it could be a blend door problem. Common among dual a/c Fords. Try disconnecting the battery for a few minutes. Sometimes this will reset the blend door actuators. If this doesn't work then the actuator will need to be replaced.

Jul 03, 2011 | 2002 Ford E350

1 Answer

My 2004 Avalanche ' heating system will not heat. No matter what the setting it either blows no air or cold air and it is 25 degrees outside so this is a problem. The engine is up to temp and I have tried...


The most likely cause is a failed blend door actuator; however I recommend a little troubleshooting. First, can you hear a clicking sound behind the dash when you turn the setting to hot? If yes, it is certainly the actuator stripping its gears. If not, check to make sure the heater hoses are both hot as they connect to the heater core at the firewall (in the engine compartment). If one or both of the hoses do not get hot, there is a blockage caused either by an air bubble or a stuck water control valve in the heater hose. If the hoses are both hot, the indication is again the blend door actuator.

Below are instructions for replacing the actuator. Look at the diagrams carefully--the big arrows point to the front of the truck and the actuator is on the side of the heater box above the outlet duct that runs to the driver's side of the floor. Also, the actuator is expensive, so I recommend you make sure it's bad and shop around a bit to get a good price. To check out the actuator, first see if you can turn the blend door by hand. If you can't turn it, maybe it's jammed. Also, reconnect the actuator after removing it and see what it does when you turn the heater to hot.

Removal & Installation
  1. Remove the floor air outlet duct extension (1) from the floor duct (2).

    jturcotte_393.gif

Fig. Remove the floor air outlet duct extension (1) from the floor duct (2)


Disconnect the electrical connection at the blend door actuator (#10 in pic below). jturcotte_394.gif

Fig. Blend door actuator and related components


Remove the blend door actuator mounting screws from the HVAC module.


Remove the blend door actuator as an assembly with the actuator cam.
jturcotte_396.gif

Fig. Remove the blend door actuator mounting screws from the HVAC module



To install:

  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam

  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).

  3. Connect the electrical connection at the blend door actuator (10).
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).


Picture of actuator:


jturcotte_57.jpg

Dec 07, 2010 | 2004 Chevrolet Avalanche

1 Answer

Damper is stuck in closed position for heat/AC. How do I open the damper. Fan works fine. 1998 Chevy Astro Van


I belive this year has the electric actuator thatcontrols the blend door, you will ned to unbolt it and turn door then reinstall actuator to hold door in that postion, this is located on heaterbox.

Aug 29, 2010 | 1998 Chevrolet Astro

4 Answers

NO heat in front of 2001 windstar van. Thumping


Blend air door may be stuck. I removed a pencil from a heater box before. It had fallen from the dash, down through the defrost vents and jamed the door.

Nov 13, 2009 | 2001 Ford Windstar

2 Answers

200 Jeep Laredo..Air is cold and fan is blowing,


there is a blend door actuator for the laredo and if is bad the air wont come out here is a pic of what it looks like and how to get to it


The single zone heater-A/C system is equipped with a single blend door actuator. The dual zone system has two blend door actuators, one for the driver side blend-air door and one for the passenger side blend-air door.
7d2da02.gif
  1. Disconnect and isolate the negative battery cable.
  2. Remove the glove box from the instrument panel.
  3. Remove the three screws that secure the blend door actuator to the passenger side of the HVAC air distribution housing .
  4. Remove the blend door actuator from the air distribution housing and disconnect the HVAC wire harness connector from the actuator.
  5. Remove the blend door actuator from the vehicle
to instal
  1. Position the blend door actuator into the vehicle.
  2. Install the blend door actuator onto the passenger side of the HVAC air distribution housing . If necessary, rotate the actuator slightly to align the splines on the actuator output shaft with those on the blend door cam .
  3. Install the screws that secure the blend door actuator to the passenger side of the air distribution housing . Tighten the screws to 17 inch lbs. (2 Nm).
  4. Connect the HVAC wire harness connector to the blend door actuator.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable.

Sep 09, 2009 | 1998 Cadillac Seville

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
1997 Chevrolet Astro Logo

Related Topics:

586 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...