Question about 1996 Chevrolet C/K 2500
Starter engages on its own
Posted by Anonymous on
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 1995 Chevy Diesel, Randomly dies
Sounds like you have a problem with the crank sensor.They can have an intermitant fault.like an open curcuit Try changing the sensor.good luck hope that was helpfull.
Posted on Jul 24, 2009
Sounds like you have a clogged PCV valve thats the valve that lets the gases that get into the crankcase be rerouted back into the intake. It's silver about two inches and is usually in a rubber fitting in the valve cover and will have a hose on the other end. it's no tools installation just pull the hose off pull it out and replace with a new one. thats the first thing i'd do - 10 mins and 10 bucks should do it
Posted on Sep 05, 2009
1994 Chevy Truck K 2500 Suburban 4WD V8-393 6.5L DSL
Fuel Cut Solenoid: Testing and Inspection
An inoperative shutdown solenoid can cause a no-start condition. Disconnect solenoid harness connector and with ignition switch in the "ON"
position momentarily touch solenoid harness connector to solenoid connector. If a "click" sound is heard, the solenoid circuit is operating
properly. If "click" is not heard, the system should be diagnosed as follows:
1. With test lamp connected to ground and the ignition switch in the "ON" position, backprobe the shutdown harness connector. If the test lamp
does not light check for open circuit form the ignition switch to the solenoid.
2. If the test lamp lights, check the ground circuit between solenoid stud and injection pump cover to see if connectors are clean and tight. If the
connections are not clean and tight repair and retest.
3. If the ground circuit is "OK", remove the injection pump cover. Connect a jumper wire between solenoid ground connector and ground. With
the ignition switch in the "ON" position, momentarily touch shutdown solenoid harness connector to shutdown solenoid terminal. If solenoid
operates, check for internal injection pump problem.
4. If the solenoid will not operate, replace the shutdown solenoid.
Fuel Cut Solenoid: Service and Repair
REMOVE OR DISCONNECT:
1. Remove pump cover.
2. Terminal contact nuts.
INSTALL OR CONNECT:
1. Solenoid in the pump cover.
- On the shutdown solenoid, make sure that the linkage is free.
- On the cold advance solenoid, make sure that the plunger is centered so that it will contact the check ball in the fitting.
2. Insulating washers on the terminal studs.
3. Terminal nuts and tighten to 1 Nm (9 in lbs).
4. Pump cover.
5. Inspect solenoid operation prior to installing the pump cover. Use a 12 volt DC power source.
Posted on Sep 10, 2009
Tips for a great answer:
Feb 16, 2011 | 1996 Dodge Ram 3500 Club Cab
May 14, 2010 | 2002 Volkswagen Golf
Apr 13, 2010 | 2004 Ford Ranger
Jan 24, 2010 | 1996 Volkswagen Golf
Nov 23, 2009 | 1996 Chevrolet C2500
Oct 30, 2009 | GMC Suburban Cars & Trucks
Jun 24, 2009 | 1987 Mitsubishi Montero
Mar 25, 2009 | 1996 Dodge Ram 3500 Club Cab
30 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: