Question about 1990 Nissan Hardbody King Cab

Open Question

Flywheel torque specs 2.4 nissan - 1990 Nissan Hardbody King Cab

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

joecoolvette
  • 5660 Answers

SOURCE: Bolt torque specs for flywheel, pressure plate,

1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.

Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.

Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!

Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)

If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.

Posted on Jul 07, 2009

redlinetech0
  • 33 Answers

SOURCE: specs on upper intake

Hi e-mail me at redlinetech07@yahoo.com There is a sequence for this. I can e-mail you the picture of the sequence and the tourqe spec.

Posted on May 23, 2009

  • 32 Answers

SOURCE: I need resurfacing specs for an rb25det flywheel please!!!!

Runout limit (on clutch disc mating surfaces) manual trans, 1.0mm, or 0.039 inch,

Posted on Aug 17, 2009

  • 59 Answers

SOURCE: what are the torque specs for the flywheel and

Flywheel 61-69 ft/lbs
Clutch cover to Flywheel 25-33 ft/lbs

Posted on Oct 06, 2010

  • 2422 Answers

SOURCE: torque specs for the flywheel and pressureplate

ON Z22 OR Z24 ENGINES FLYWHEEL 101-116 FT-LBS 137-157 N-M PRESSURE PLATE TO FLYWHEEL IS12-15 FT-LBS 16-21 N-M

Posted on Oct 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the torque specs for flywheel bolts on a Nissan NP 200 bakkie. It has a Renault K7M engine - 1600 cc


you will need the torque specifications for the renault engine not nissan
the bolts may be different sizes and incorrect torque readings may snap off the bolts

Dec 17, 2016 | Nissan Cars & Trucks

1 Answer

Flywheel torque spec's for 1983 Ford F-100


Could it be a F-150 instead?
Ford Engine Bolt Torque Chart Bolt Torque Spec Chart for Ford Engines

These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use after-market performance bolts like ARP's, you should follow the recommended torque specifications.

260, 289, 302 Torque Spec.
Fastener Type Torque Spec Main cap bolts 60-70 ft-lbs Outer main cap bolts 35-40 ft-lbs. Connecting rod bolts (40-45 ft-lbs. for 289 HP & Boss 302) Cylinder head bolts 65-72 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs Oil pump bolt 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolts 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351W Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 90-100 ft-lbs. Rocker arms 17-23 ft-lbs. Intake manifold bolts 23-25 ft-lbs. Oil pump bolts 23-28 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 8-10 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 351C, 351M Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (45-50 ft-lbs. For Boss 351C) Cylinder head bolts 105 ft-lbs. (125 ft-lbs. For Boss 351C) Rocker arms (non-adjustable) Rocker arms (non-adjustable) 5/16in. intake manifold bolts 21-25 ft-lbs. 3/8in. intake manifold bolts 28-23 ft-lbs Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Cam thrust plate bolts 9-12 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs. 360, 390, 406, 427, 428FE Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs. Crossbolts for 406-427 40 ft-lbs. Connecting rod bolts 40-45 ft-lbs. (53-58 ft-lbs. For 406 and 427) Cylinder head bolts 80-90 ft-lbs. (100-110 ft-lbs. For 1963-67 427) Rocker arm shaft bolts 40-45 ft-lbs. Intake manifold bolts 32-35 ft-lbs. Oil pump bolt 12-15 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-15 ft-lbs. 429-460 Torque Spec.
Fastener Type Torque Spec Main cap bolts 95-105 ft-lbs Connecting rod bolts 40-45 ft-lbs. Cylinder head bolts 140 ft-lbs. Rocker arms (non-adjustable) 18-22 ft-lbs. Intake manifold bolts 25-30 ft-lbs. Oil pump bolt 25 ft-lbs. Cam bolts 40-45 ft-lbs. Harmonic damper bolt 70-90 ft-lbs. Flywheel / flex-plate bolts 75-85 ft-lbs. Pressure plate bolts 35 ft-lbs. Front cover bolts 12-18 ft-lbs.

Dec 18, 2015 | Ford Cars & Trucks

1 Answer

What is the torque setting for nissan navara v6 4lt2007 flywheel torque


there are 2 sets of torque specs for flywheel bolts as there are 2 different fly wheels in use with different bolts for each
go google and type in--torque specifications for nissan navara flywheel bolts and fins a site relevant to you application
it could be 61-69 ft/lbs a or 90 ft lbs depending on the flywheel and the vehicle 2wd or 4wd

Sep 30, 2015 | Nissan Cars & Trucks

1 Answer

1987 nissan d 21 4x4 4cylinder z motor need torque specs for flywheel to crank and presher plat to flywheel


It amazes me how many questions are asked about torque specs. Anyone going into an engine deep enough to need them should be working from a shop manual. I'm 67 years old and been wrenching since I was 14. Over the years I've bought more than 100 vehicle specific books and I still will not tackle a new type car or truck without a shop manual. They are cheap and full of tips and tricks to insure you don't screw something up. Use them folks!

Dec 12, 2014 | Cars & Trucks

1 Answer

Nissan frontier starter binds the flywheel


You need to put shims in between the starter and the engine block.You should be able to pick them up at your local auto parts store.

Oct 31, 2012 | Nissan Frontier Cars & Trucks

1 Answer

What is flywheel torque specs for 1994 nissian pickup, 4 cyl.


Apply Loctite to the bolt threads, then torque to 72 to 80 Ft-lbs.

Apr 21, 2011 | Nissan Pickup Cars & Trucks

1 Answer

Torque specs for the flywheel and pressureplate


ON Z22 OR Z24 ENGINES FLYWHEEL 101-116 FT-LBS 137-157 N-M PRESSURE PLATE TO FLYWHEEL IS12-15 FT-LBS 16-21 N-M

Oct 10, 2010 | 1984 Nissan Pickup

1 Answer

What is the torque specs on a 1990 nissan pathfinder cluch.


If you are talking about the pressure plate to flywheel bolts, the torque is 16 to 22 foot pounds.

Feb 14, 2010 | 1990 Nissan Pathfinder

1 Answer

Bolt torque specs for flywheel, pressure plate, bell housing bolts for 97 Nissan maxima


1.Flywheel - 61 to 69 Foot Pounds
2.Pressure Plate - 25 to 33 Foot Pounds
3.Bell Housing - No specs found. I would say 25 to 35 foot pounds should be sufficient.

Bolts clean on ->flywheel to crank, ->pressure plate to flywheel, and ->bell housing to back of engine, I would use TWO drops of Loctite Red threadlocker, on ALL of these bolts.

Hope you have an alignment tool for your clutch disk when you install it. Auto parts stores sell the plastic one's cheap! Saves a LOT of headaches!

Tighten the pressure plate EVENLY! Snug the bolts down until they just TOUCH, then go in a criss-cross pattern when tightening. Do the tightening in incremental stages! You turn one bolt one thread, you go across to the opposite side, and turn that bolt one thread. Keep criss-crossing so the pressure plate goes down EVENLY. (YES, it's a pain in the keister!)

If NOT, you'll have a warped pressure plate, and it will be junk!
Thanks for letting me say that, I feel better.

Jul 07, 2009 | 1997 Nissan Maxima

Not finding what you are looking for?
1990 Nissan Hardbody King Cab Logo

Related Topics:

1,105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...