Question about 2008 Chrysler Sebring

Open Question

How to change thermostat on 2008 chrysler sebring on 2.4 litre engine.

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 36 Answers

SOURCE: To reset the change engine oil indicator

Owners manual should have the info you need to reset it

Posted on Dec 13, 2008

Ad
  • 2 Answers

SOURCE: replace air filter 2002 Chrysler Sebring convertible

you need to loosen the clamp on the throttle body and unplug the map sensor then there are two clips on the other end pull that out and you should be able to pull the filter out you don't need to take the box off.

Posted on Apr 28, 2009

polarcycle
  • 1392 Answers

SOURCE: 1999 chrysler sebring, transmission doesnt shift

find out why the light is on and fix it. This will most likely be a trans wiring issue that the light is on for.

Posted on Jul 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does my 2008 Chrysler sebring have two thermostats


there is only one thermostat on your car. what you probably have is split temp control one to set temp for the passenger side and one for the drivers side. if so then the temp control door on the passenger side is probably not functioning properly. take it to a shop to have fixed.

Nov 30, 2014 | 2008 Chrysler Sebring

1 Answer

I would like to see a picture of a thermostat housing LOCATION on the engine of a 2005 Chrysler Sebring 2.7L V6. I have already replaced the upper water outlet housing, and was told it is not where the...


Click over image for zoom...

zjlimited_1292.jpg

Fig. Air bleed valve (1) and thermostat housing (2) 2.7L-engine


Hope this helps (remember to rate and comment this free answer).

May 26, 2011 | 2005 Chrysler Sebring Conv

1 Answer

Where is the thermostat located on a 97' Chrysler Sebring


to the front of the engine, just behind the radiator you will notcie 2 wires connecting to a part on the engine, close the the manifold. thats the thermostat. Its close to the radiator hose,,

May 07, 2011 | 1997 Chrysler Sebring

1 Answer

How to change thermostat 04 sebring 2.7


The thermostat is located on the left side (standing from the back of the engine) under the Alternator. First step is to remove the neg bat cable. Try to use a mem-saver as it will save you alot of headache trying to reteach the PCM Remove the Alternator, be careful not to break the electrical connectors. You should be able to see the thermostat housing (looks like half a ball with 2 hoses coming out of it) Drain the coolant, and remove the housing..there are 3 bolts. Note the position of the old thermostat before removal. Install the new thermostat in exactly the same position, with the spring-end facing the engine. Clean any debris and residue from the inside of the housing cover. Put the new gasket on the thermostat and install. After everything is back as it was, re-fill the radiator start the engine and turn your heater on full. Watch for leaks.

Apr 05, 2010 | 2004 Chrysler Sebring

1 Answer

My 2008 chrysler sebring will start the engine but


shift lock switch. this switch is usually connected to a little box on the brake pedal. Look about half way up the pedal from the foot pad and make sure the wires are still intact.

Aug 13, 2009 | 2008 Chrysler Sebring Convertible

2 Answers

Reset oil change message.


YOU TURN IGNITION TO RUN POSITION..ENGINE OFF..PRESS ACCELERATOR 3 TIMES WITHIN 10-15 SECONDS..RELEASE AND TURN KEY OFF..THEN START VEHICLE,IT SHOULD BE RESET

Jul 11, 2009 | 2008 Chrysler Sebring

1 Answer

How do i change the digital clock on the 2008 sebring?


there should be a "H" and a "M" on the console with a small hole beside it,use a pen to push the recessed buttons

May 06, 2009 | 2008 Chrysler Sebring

3 Answers

Engine knocking and oil lampe illuminated during idle


Change oil and filter. Use a synthetic blend oil, add 1/2 pint of marvel mystery oil, and drive for a short time, 30 minutes or so. If knock continues, the damage is already happened. Use only synthetic blend or synthetic oil in the 2.7 litre engine.

Jul 09, 2008 | 2002 Chrysler Sebring

Not finding what you are looking for?
2008 Chrysler Sebring Logo

Related Topics:

755 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...