Question about 2007 Jeep Commander Rocky Mountain

Open Question

Changing air filter 2008 Jeep Commander - 2007 Jeep Commander Rocky Mountain

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 19 Answers

SOURCE: Can't locate air filter...

1. Loosen clamp (1) and disconnect air duct at air cleaner cover (3). 2. Pry over 4 spring clips (5) from housing cover (spring clips retain cover to housing). 3. Release housing cover (3) from locating tabs on housing and remove cover (3). 4. Remove air cleaner element (filter) from housing.
cecdf0c.jpg

Posted on Jun 30, 2009

Ad
  • 1 Answer

SOURCE: location of oil dipstick

The oil dipstick is located at the back of the engine.  If you look at the engine from a top view it is located at about 11 o'clock.  It's black.

Posted on Dec 22, 2008

greg_margo
  • 1959 Answers

SOURCE: Jeep Commander Rear Brake Pad Installation

Per Chilton Auto repair manual:

Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

Posted on May 17, 2009

  • 135 Answers

SOURCE: I just had my oil changed on my 2008 jeep

It is not being reset properly.

Posted on Aug 05, 2009

Molson02536
  • 3854 Answers

SOURCE: location of cabin air filter

It can have a cabin air filter, but most vehicles ship without it. Either way, you can access the cabin air filter housing by opening the glove box all the way (squeeze the sides so it clears the stops).

The filters are around $15 at the dealer.

Whether or not there's a cabin filter installed, make sure you're also following Chrysler's recommendations in the owner's manual—running the air on recirculate all the time will encourage mold and bacteria to grow.

Good luck


Posted on Nov 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 JEEP COMMANDER RADIO CODES


asked here like 10,000 times
and on the internet 1million times
and the answers never change,
ever google ?
my guess is you are trying to ask for the secret
antitheft radio password unlock codes?>

see the 6 choices here.
http://www.fixkick.com/power-elect/Keep-Alive/keep-alive.html#radio

see the 22 million hits there.

the radio is bricked we call this.
works just like a brick, dig?

Jul 20, 2015 | 2008 Jeep Commander Overland

1 Answer

How to remove air filter top on 2008 jeep commander


all cars are either screws or snaps. did you LOOK yet?

Apr 20, 2014 | 2008 Jeep Commander

1 Answer

What can cause my 2008 jeep commander 4.7l V8 to feel sluggish when accelerating? I've changed the plugs, egr valve, map sensor, air filter, pcv valve and oil. I started to notice it after my catalytic...


Why would you be at a dealer?
Why did the exhaust converter fail in
under 12 to 14 years
You know that issue has to be solved long before
a new cat goes on
You need to look at cylinder misfire counts
Fuel Trim
Engine Temp
Cat Temp
& all data
I wouldn't expect a dealer to do what you ask
or tell you a thing, if you asked
Start over at a local shop & be there from time to time
Don't tell them how to do their job, but be proactive.

Aug 12, 2013 | 2008 Jeep Commander

1 Answer

WHERE IS THE #7 CYLANDER LOCATED ON 2008 JEEP COMMANDER LIMITED


google firing order diagram for 5.7 hemi
than google jeep comander forums to get a solution to the misfire code

Feb 05, 2013 | 2008 Jeep Commander 5.7

1 Answer

We have a 2008 jeep commander, check engine light is on. ran a diagnostic because of engine noise, it said cylinder 4 misfire. so far we replaced the or, sparkplug, and coil for cylinder 4, it still h


google jeep commander forums join one and post youre question there if no luck than google grand cherokee forums and try there it is basicially the same vehicle

Feb 05, 2013 | 2008 Jeep Commander

1 Answer

2008 Jeep Commander Radio Does Not work after changing battery


Make sure the wires that are connected to your battery are so if not by u disconnecting the battery u reset it the system check ur alarm installer..

Oct 21, 2012 | 2008 Jeep Commander

1 Answer

2008 Jeep Commander with 5.8l Hemi problems with instrument panel


Have shop run an OHM test on your transmission sensors -- then have them replaced and rerun the OHM test. -- it's more than likely an input speed sensor that is not working properly and telling the jeep to go into "limp mode" hence your speed isn't changing but it can't read the actual speed.

Apr 13, 2010 | 2006 Jeep Commander

1 Answer

Can't locate air filter...


1. Loosen clamp (1) and disconnect air duct at air cleaner cover (3). 2. Pry over 4 spring clips (5) from housing cover (spring clips retain cover to housing). 3. Release housing cover (3) from locating tabs on housing and remove cover (3). 4. Remove air cleaner element (filter) from housing.
cecdf0c.jpg

Jun 30, 2009 | 2007 Jeep Commander Rocky Mountain

Not finding what you are looking for?
2007 Jeep Commander Rocky Mountain Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...