Question about 2000 Jeep Grand Cherokee

Open Question

Trans feels like limp mode no check engine light

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 412 Answers

SOURCE: 2007 Jeep liberty auto trans will not shift from 2nd

YOU NEED TO HAVE TRANSMISSION CONTROL SYSTEM SCANNED..IT HAS DETECTED A PROBLEM IN THE ELECTRICAL SYSTEM,INTERNAL OF TRANS OR A SENSOR FOR TRANSMISSION..A TRANSMISSION IS AN EXPENSIVE COMPONENT..YOU SHOULD GET IT CHECKED ASAP..ESPECIALLY IF YOU HAVE NO WARRANTY LEFT

Posted on Jul 07, 2009

Ad
  • 159 Answers

SOURCE: 2005 Grand in limp mode

without a dtc to help,the only thing you can do is check all the connections at the transmission,and unhook the battery for awhile or get check code cleared and see if it reapperars

Posted on Oct 03, 2009

  • 6982 Answers

SOURCE: transmission doesn't shift, stays in one gear

The point you are at now is when you should have a good transmission shop do a "ride along" scan test to determine if the problem is in a control unit or the trans itself. The control module takes information from the engine management system as well so if something such as your throttle position sensor on the throttle body has failed (or even the map sensor) the trans control may not allow proper shifting.
While it is possible to do continuity and individual component tests on the entire system,(to a point) the fastest and most accurate means of diagnosis is to have a shop do that for you. Then, if you want, do the actual repair work yourself!

Posted on May 12, 2010

blueextc3221
  • 15935 Answers

SOURCE: Have a Jeep Grand Cherokee

The issue, then, may be with the OBD or ECM itself.

Thanks!

Posted on Dec 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

05 frontier in limp mode no codes transmission just replaced


If you paid a professional to replace the trans, go back to him first so he can give his opinion. Before you do, check the fluid level of the trans, and the condition of the fluid. Any sign of water?
But the problem may not be the trans, there could be faults in the engine or cooling system causing the ECU to select limp mode to get you back home.
Have you scanned the computer directly with a scanner?
Don't rely on the check engine light for very thing relating to codes.

May 26, 2015 | 2005 Nissan Frontier

1 Answer

I have a jaguar s type 2000 it writes gearbox fault and is in limp mode funny the fan is noisy to,please help


You must have a check engine light on in your dash. You first need to pull up the code. I will assume your trans is an automatic. If so, when your trans goes into limp mode, if you stop , shut off your motor, and start again, does your car run OK again, till the next time it goes into limp mode. If so you have a bad trans solenoid. Sometimes this solenoid is on the outside of a trans and sometimes it's on the inside. If inside you would have to drop the pan, and valve body, because it's on top of the valve body. The fan is a separate issue. GOOD LUCK FRIEND.

Nov 17, 2014 | Cars & Trucks

1 Answer

Changed transmission computer still have code 605 wont shift out of 2nd gear


did you have pinion factor and quick learn performed on the trans module after replacement? if not then the trans won't shift correctly. also is the check engine light on with any engine codes in memory? the engine module may the trans stuck in limp-in mode(2nd gear).

Aug 10, 2011 | Chrysler PT Cruiser Cars & Trucks

1 Answer

Check engine light car feels like its in high gear


The problem is most likely a PNP(shift position switch) problem. When this happens, the trans goes into limp home mode. The trans goes into high gear and doesn't allow any shifting up or down. This is to protect the trans.

Apr 06, 2010 | 2000 Volvo V40

3 Answers

EML, Check Engine, Limp Mode


What is limp mode, and it is MiL light( mal function indicator light)it is not EML. Please specify so i can help

Jul 24, 2009 | 2001 BMW Z3

2 Answers

Limp Mode


the check engine light will be on 

Mar 15, 2009 | 1994 Jaguar XJ6

2 Answers

1997 isuzu wizard mu check light


Code 24 is a vehicle speed signal sensor fault, the sensor most likely does not provide a useable signal until about 25 MPH, when the computer doesn't see any signal after that speed it turns on the light. Make sense?

Sep 08, 2008 | 1997 Isuzu Oasis

2 Answers

Limp in mode


you have to change the solenoid control if your car is 3.5 engine the solenoid control located at inside the transmission..

Aug 19, 2008 | 2004 Dodge Intrepid

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...