Question about Cars & Trucks

Open Question

Hyundai lantra j2 1.8l timing mark digram - Cars & Trucks

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: couldn't find the sprocket mark

If you are refering to the timing belt/ chain sprokets. Make your own marks with white paint. Also before removing the belt or chain use plastic cable ties to secure any pulleys/ sprockets so they cannot move. I used this method when replacing the timing belt on a vauxhall calibra v6 24v.

Posted on Jul 26, 2008

Ad
  • 2 Answers

SOURCE: timing belt have be removed before mark

maybe u can try use an sharp object like srew driver scrath around the cam body..coz it maybe hidden with some dirt..but if like my eg8,i will put a mark b4 put off evrything especially the timing belt..

Posted on Aug 08, 2008

countrysi248
  • 443 Answers

SOURCE: Hyundai Lantra 19999 Timing Mark

are you setting the timing belt or just setting the timing with a light ? if you are setting the timing it should be set at about 10 before top dead center or maybe would run a little better at 12 or so thanks jerry holler if you have more .

Posted on Feb 07, 2009

  • 510 Answers

SOURCE: Timing marks setting Hyundai Lantra

Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top


Posted on Mar 21, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hyundai lantra continues to stall as the clutch is depressed. and oil light turns on. i have no idea what is going on with it so any help would be muchly appreciated.


problem would seem to be in the running of engine ,when was it last serviced ,old plugs , air filter etc will affect engine idle speed which is why its stalling when dipping clutch

Mar 25, 2014 | Hyundai Elantra Cars & Trucks

1 Answer

1997 Hyundai Lantra - Dash lights don't come on with headlights


Check the fuse. Also make sure your dimmer for the dash lights does is not turned all the way down. If all that checks out, your dimmer may be need replaced.

Oct 17, 2012 | Hyundai Lantra Cars & Trucks

1 Answer

1996 HYUNDAI LANTRA STALLING RANDOMLY


Throttle position sensor, check that, or fuel pump/filter

Jul 02, 2012 | 1997 Hyundai Elantra

1 Answer

Timing marks setting Hyundai Lantra


Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top


Mar 21, 2010 | Hyundai Motor 1996 Elantra

1 Answer

Gear box dip stick location- hyundai lantra automatic


try the left side of the engine... gear oils smell are diffent from the engine oil and the viscosity... gear oils are thicker... u wont go wrong on this...

Jul 19, 2009 | Hyundai Motor 1994 Elantra

1 Answer

Diagram for timing belt marks


there are books for that or check google images. make sure you find out for sure

Apr 24, 2009 | Hyundai Excel Cars & Trucks

1 Answer

Hyundai Lantra 1994


After some extensive research, it looks as though they have two totally different body styles as well as a few others. The differences are as follows:

Lantra: 1.5L
Elantra: 1.6L or 1.8L engine sizes

Lantra: 2,336 lbs
Elantra: 2,500lbs Weight

Lantra: 11.89 gal
Elantra: 13.7 gal fuel capacity

those are only three differences that i have put up among the many that i have found. Lantra's also seem to be one of those out of states type cars that you find in Australia mostly. The body is also totally different.

Feb 23, 2009 | Hyundai Motor 1994 Elantra

1 Answer

Hyundai Lantra 19999 Timing Mark


are you setting the timing belt or just setting the timing with a light ? if you are setting the timing it should be set at about 10 before top dead center or maybe would run a little better at 12 or so thanks jerry holler if you have more .

Feb 07, 2009 | 1996 Hyundai Sonata

2 Answers

Timing belt have be removed before mark


maybe u can try use an sharp object like srew driver scrath around the cam body..coz it maybe hidden with some dirt..but if like my eg8,i will put a mark b4 put off evrything especially the timing belt..

Jul 26, 2008 | Hyundai Motor 1999 Elantra

1 Answer

Couldn't find the sprocket mark in my Hyundai Lantra 1999. Pls help


If you are refering to the timing belt/ chain sprokets. Make your own marks with white paint. Also before removing the belt or chain use plastic cable ties to secure any pulleys/ sprockets so they cannot move. I used this method when replacing the timing belt on a vauxhall calibra v6 24v.

Jul 26, 2008 | Hyundai Elantra Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...