Question about Cars & Trucks

Open Question

Need wiring diagram for Kubota L4200

Fuel sender unit has no wire and can't find where one should go, help.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76673 Answers

SOURCE: radio wiring diagram needed

This is the only thing I could find, it is from a car audio site, hope it helps.

Car Radio Battery Constant 12v+ Wire: Green/Yellow
Car Radio Accessory Switched 12v+ Wire: Yellow/Black
Car Radio Ground Wire: Chassis
Car Radio Illumination Wire: Blue/Red
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: 5′
Car Audio Front Speakers Location: Dash
Left Front Speaker Positive Wire (+): Orange/Green
Left Front Speaker Negative Wire (-): Black/White
Right Front Speaker Positive Wire (+): White/Green
Right Front Speaker Negative Wire (-): Black/White
Car Audio Rear Speakers Size: 6′ x 9′
Car Audio Rear Speakers Location: Rear Deck
Left Rear Speaker Positive Wire (+): Pink/Green
Left Rear Speaker Negative Wire (-): Pink/Blue
Right Rear Speaker Positive Wire (+): Pink/Blue
Right Rear Speaker Negative Wire (-): Green/Orange
-->

Posted on Aug 29, 2008

Ad
  • 2 Answers

SOURCE: vw t25 campervan

The temperature guage sensor is located on the thermostat housing. I would start simple and check the wiring. clean the connectors.

Posted on Nov 19, 2008

  • 170 Answers

SOURCE: 02 jeep grand cherokee 4.7 eng

Hook up a manifold gauge (mechanical temporary use gauge, used by mechanics) and test the oil pressure. You probably need to replace the gauge. The computer sends info through a printed circuit board behind gauge cluster and sometimes you have to replace the whole gauge cluster.

Posted on Feb 06, 2009

  • 84 Answers

SOURCE: electric fuel pump wiring harness diagram

Your best bet is to type it in to autozone.com and got to the repair section. it will tell you there.

Posted on Apr 23, 2009

johnjohn2
  • 5763 Answers

SOURCE: need a diagram for wiring trying to trace wiring

Heres a wiring diagram for the fuelpump.bbadc54.gif

Posted on Oct 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring diagram for kubota bx2230 d


Request the wiring diagram directly from Kubota.

Sep 16, 2017 | Cars & Trucks

1 Answer

Free nissan wiring diagrams


You may have to get a manual to find the color codes. But only one cable goes to the fuel gauge sender it travels in the wiring loom to one side of the fuel gauge, and from the other side to the ignition switch.

Aug 16, 2014 | Cars & Trucks

1 Answer

Fuel gage on my 01 couger does not work but the low fuel light on the gage is on would like to know what the wiring diagram is and if anyone can give advice on where to go from here


check power to the sender unit in the fuel tank may be a break in the wire in your trunk/boot. if not change the sender unit.

Dec 27, 2013 | Cars & Trucks

1 Answer

I just replaced the fuel pump in my 1996 explorer and fuel filter and put 5 gals of gas back in the tank now the fuel guage is registering full and will not work


Eewww. That's not good. And you're not going to like what I say. I think you bent the fuel gauge sender unit, or misaligned something when you put it back in tank. Try unplugging the connector and plugging it back in. See if that helps the gauge to register right. Here's a quick check to see if your dash gauge is working right: Unplug connector again at tank and use a jumper wire to ground the dash gauge sender wire. With key turned to on and the fuel gauge wire grounded, the gauge should jump up to half or full. If it does, there's a problem with your sender unit in the tank.

Nov 07, 2011 | 1996 Ford Explorer

1 Answer

Citroen xsara fuel gauge


Your most likely fault / problem, is with the fuel gauge sender unit being faulty - which is in the tank..

Its rare that gauges fail - but its worth checking... Access the fuel tank where the fuel pump fits in under the rear seats (i think) and remove the wire for the gauge, this is the smallest wire on the unit.

Earth that wire (ground), with the ignition on... make sure its a good earth - and the gauge should be seen to rise right to the top... if that happens - it proves the wiring and gauge are ok.. if not - then there is a problem with the wiring or gauge - most likely the latter which would need investigating.

Its usually the sender unit though as I say - 99.9 % of the time.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Nov 04, 2011 | Cars & Trucks

1 Answer

I need a wire diagram for 1998 blazer fuel injection. I believe the injector ground wire might be corroded. Where is that ground wire?


Haynes Manual 24071 includes wire diagrams for all components. On the injector you have a pink and dark blue wire both are hot and signal wires. The only ground in the system is on the fuel pump and sender unit. Diagram 12-26 in the haynes maual.

Feb 03, 2010 | 1998 Chevrolet S-10 Pickup

2 Answers

Fuel gauge shows quarter tank then the low fuel light comes on showing eighth of tank


Most likely it's one or BOTH fuel level sender units in the fuel tank (there are two float units, one with the fuel pump). Located under the rear pass seats on the driver's side and another on passenger side (seats need to be moved out of the way to get to them - four 14mm bolts with each seat).
6112ec7.jpg
You'll see the 8mm screws holding the units in place.
b22773a.jpg
Wiring Diagram:









8047594.jpg In this diagram, the sender units are wired in series (one or both may be causing your problem). The sender units are simple potentiometers (rheostats) & their combined resistance tell the microcomputer in the instrument cluster what the fuel level is, then It tells the fuel gauge where to put the needle. Inspect your wiring connectors to these sender units first. These sender units can be ordered/purchased at a Hyudai Parts Department. I don't believe there are any after-market units available - they are a dealer item.

Jun 09, 2009 | 2004 Hyundai Santa Fe

1 Answer

I need to replace the fuel pump in my 940 Volvo.


Disconnect battery ground strap before beginning to work on the fuel/electrical system. Do not smoke or have anything in the area which can ignite or cause sparks

  1. Drain enough fuel from tank to prevent spilling, no more than 4 gallons (16 liters) of fuel should remain. Use suitable pumping equipment.
  2. Remove floor mat and panel from trunk.
  1. Disconnect wiring harness connector to sending unit. Remove wires from connector.
  2. Disconnect ground wire to sender. Push wires through grommet.
  3. Remove cover for access to tank sending unit.
  1. All models: Disconnect from the fuel tank sending unit:
    1. Breather hose C
    2. Return hose A
    3. Supply hose B
    4. Filler hose D
    5. Wiring harness from clip E
  1. Clean area and unscrew fuel tank sender/pump cap or equivalent. Remove tank sender/pump and seal.
  2. Remove pump from sender/pump assembly.
INSTALLATION
  1. Inspect the pump for damage, feed pump hose and wiring for wear. Replace as needed.
  2. Install new pump to sender/pump assembly.
  3. Install rubber seal in neck of tank. Lubricate inside of seal.
  1. Install fuel tank sender/pump unit. Align it with the moulded joint (arrows) on tank.
  2. Apply rustproofing compound to exposed metal portions of tank sender.
CAUTION : With tape or rubber caps, protect fuel sender openings from overspray.
  1. Torque fuel tank sender/pump lock ring to: 22 ft-lb (30 Nm)
  2. Reassemble components in reverse order. Use tie straps to secure all hoses and wiring.

Jun 04, 2009 | 1995 Volvo 940

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...