Question about Chevrolet Camaro

Open Question

Vacuum diagram for 1987 z28 camaro 350 tuned port injection

Vacuun line digram

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2920 Answers

SOURCE: misfiring

its going to be in the timing you might check the distributor cap for hairline cracks and make sure there arent any but at this point it sounds like timing is off or going out

Posted on Jan 22, 2009

  • 10 Answers

SOURCE: have a 1987 iroc z28 had a 305 tune port in it now

WIRING FOR WHAT -THE PLUGS WIRING ARE THE SAME YOU NEED A MSD 6 AL BOX OR LIKE THAT FOR THE IGN,THE WIRING DIAGRAM ARE IN THE BOX

Posted on Jul 27, 2009

carfreakt
  • 68 Answers

SOURCE: why does my rebuilt 305 tuned port injection chevy

wires crossed vacuum leak bad injectors MAF sensor crank sensor did they change the cam

Posted on Oct 05, 2009

  • 2309 Answers

SOURCE: 85 chevy camaro 5.0 tuned port injection,,whats

with no one piston at tdc, the rotor should be pointing at no1 cyl, firing order is 1 8 4 3 6 5 7 2

Posted on Dec 05, 2009

  • 2309 Answers

SOURCE: how to change a head gasket in a v8 350 5.7 liter

don't attempt it without a manual with specs, you will need special tools like a torque wrench and an angle meter, you will have to get the head measured and probably resurfaced, also do it in a clean enviroment, and make sure all is spotless during reassembly, even a fingerprint on mating surfaces can cause premature failure of gaskets

Posted on May 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On my 1994 camaro z28 lt 1, i broke the vacuum lines and when i replaced them my tranny does not go to O.D.and acts like dont wont to change.


There is a vacuum modulator on the side on the transmission that needs a vacuum to it. It has to be to a direct vacuum port. Not thru a switch or valve.

Aug 15, 2014 | 1994 Chevrolet Camaro

1 Answer

How to use a vacuum diagram when you don't understand abbreviations and there are no pictures of motor? I am working on an 1987 Ford 350 econaline RV . The trouble is running at idle. I put it in gear and...


did you do tune up to fix this problem of stalling or has it been doing it after you did tune up? Just asking maybe i can steer you in a different direction

Jul 25, 2010 | 1987 Ford Econoline

1 Answer

Blown head gasket


This is a major overhaul requiring special tools and expertise.

May 27, 2010 | 1989 Chevrolet Camaro

1 Answer

Installing tuned port back on 86 iroc but using another hareness and computer and tuned port but need wiring diagrams , do u have to use esc on tuned port


The tuned port injection is specific and need's the proper wiring harness for the application, and the same with the computer.

Mar 07, 2010 | 1986 Chevrolet Camaro

1 Answer

Why does my rebuilt 305 tuned port injection chevy camaro run very rough timing seems good giv it gas and it kills


wires crossed vacuum leak bad injectors MAF sensor crank sensor did they change the cam

Oct 05, 2009 | 1987 Chevrolet Camaro

2 Answers

I have a 1987 Camaro Iroc Z28 5.0 engine. I'ts


Fuel pump is located in the fuel tank. A shop can do a fuel pressure pretty easy. You could do it to, you just have to spend 50 to buy a tester, or spend 20 to have a shop do it.

Aug 16, 2009 | 1987 Chevrolet Camaro

1 Answer

Have a 1987 iroc z28 had a 305 tune port in it now has a 350 carb need the wiring setup for this type of conversion


WIRING FOR WHAT -THE PLUGS WIRING ARE THE SAME YOU NEED A MSD 6 AL BOX OR LIKE THAT FOR THE IGN,THE WIRING DIAGRAM ARE IN THE BOX

Jul 27, 2009 | Chevrolet Camaro Cars & Trucks

1 Answer

Looking for a wiring diagram 1987 Z28 camaro


bruce in the wireharness on the plugins they have numbers, write them down and go to the neares chevy dealerchip,talk to the parts personel if posible to the parts manager.and talk to him about the problem you are running into ,then they can ck the numbers to see if you have the right wireharness for your z28 camaro,you might have a harness for a camaro but it could be tha its for a v6 or just a camaro, and not a z28 camaro that couid be the diference.let me know

May 31, 2009 | 1987 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...