Question about 1997 Pontiac Grand Am

Open Question

1992, 3.3 engine, power steering pump bolt pattern

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 79 Answers

SOURCE: trying to change water pump on my 1998 bonneville

Ok here it is. Remove the two bolts thru the holes in the power steering pump pulley. Leave the power steering pump where it is just move it aside a little to access the bolt or bolts. Then it is hard to line up the power steering holes to the block so be careful and good luck.

Posted on Aug 27, 2009

  • 15 Answers

SOURCE: 1 have a 1992 pontiac grand prix, 3.4L and i need

look for the only belt pulley that isnt running anything. Its called the idler pulley use a 3/8 ratchet look for a square hole beside the pulley use ratchet to move spring loaded idler pulley and remove belt

Posted on Sep 30, 2009

  • 540 Answers

SOURCE: removing water pump on 97 grand prix gt. Power

no you have to go thru the holes in the front of the power steering pulley. Usually a ratchet with a deep 13mm socket will do to remove the 2 bolts located at 12 and 6 o'clock then you will be able to move it out of the way

Posted on Jan 11, 2010

archaeology
  • 662 Answers

SOURCE: need instructions for power steering

-- from the 1990-1999 Lumina / Silhouette / TranSport Repair manual ---

1992 Pontiac TransPort Power Steering Pump REMOVAL AND INSTALLATION

  1. Disconnect the negative battery cable.
  2. Disconnect and cap the power steering pump hoses.
  3. Remove the accessory drive belt.
  4. Remove the power steering pump pulley using a suitable puller tool.
  5. Remove the pump mounting bolts and remove the pump from the vehicle.

See Figures 1, 2 and 3


0900c152801dbcf7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: On some vehicles, you must use a puller to remove the power steering pump pulley


0900c152801dbcf8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Power steering pump mounting-early model vehicle shown


0900c152801dbcf9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Power steering pump mounting-late model vehicle shown

  1. Installation is the reverse of the removal procedure. Tighten the pump mounting bolts to 18 ft. lbs. (25 Nm).
  2. Bleed the power steering system to remove trapped air. Air in the system could cause noise and or damage to the pump.

BLEEDING

This procedure requires the help of an assistant.
  1. With the engine OFF, the wheels off the ground and turned all the way to the left, fill the fluid reservoir to the FULL COLD mark on the fluid level indicator.
  2. With an assistant checking the fluid level and condition, bleed the system by turning the wheels from side to side without hitting the stops. You should repeat this at least 20 times, making sure to keep the fluid level at the FULL COLD mark.

Fluid with air in it has a light tan appearance. This air must be eliminated from the fluid before normal steering action can be obtained.
See Figure 4


0900c152801dbcfa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Power steering bleeding procedure

  1. Start the engine, and while it is idling, recheck the fluid level and add as necessary to reach the FULL COLD mark.
  2. Return the wheels to the center position. Lower the front wheels to the ground and continue running the engine for 2 or 3 minutes.
  3. Road test the vehicle to make sure the steering functions properly and is free of noises.

See Figure 5


0900c152801dbcfb.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 5: Torque specificatio

Posted on Jan 02, 2011

BCAS1298
  • 3092 Answers

SOURCE: how do you take off power steering pump to get to

You do not need to remove power steering pump, you can rent a power steering pulley puller tool from most auto parts, just remove the pulley, its much easier and faster, they you can get to that end bolt on the water pump.

Posted on Oct 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How involved is it to replace a power steering pump on a 2007 Explorer 4.0?


Power Steering Pump - 4.0L Special Tool(s) Installer Set, Teflon® Seal
211-D027 (D90P-3517-A) or equivalent Material Item Specification MERCON® V Automatic Transmission Fluid
XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada) MERCON® V
Item Part Number Description 1 388898 Teflon® seal 2 - Pressure line-to-pump fitting (part of 3A719) 3 W700839 Power steering pump bolts (3 required) 4 3A674 Power steering pump 5 W503924 Pressure line bracket-to-engine bolt 6 3691 Power steering pump supply hose 7 W503924 Power steering pump supply hose bracket bolt
Removal
NOTICE: While repairing the power steering system, care should be taken to prevent the entry of foreign material or failure of the power steering components may result.

  1. Using a suitable suction device, remove the power steering fluid from the reservoir.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to Section 100-02.
  1. Remove the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Remove the pressure line bracket-to-engine bolt.
  1. Remove the power steering pump supply hose bracket bolt.
  1. Release the power steering pump supply hose clamp and disconnect the hose.
  1. Disconnect the pressure line-to-pump fitting.
    • Remove and discard the Teflon® seal.
  1. Remove the 3 bolts and the power steering pump.
Installation
  1. NOTE:A new Teflon® seal must be installed.Using the Teflon® Seal Installer Set, install a new Teflon® seal to the pressure line fitting.
  1. Position the power steering pump and install the 3 bolts.
    • Tighten to 25 Nm (18 lb-ft).
  1. Connect the pressure line-to-pump fitting.
    • Tighten to 75 Nm (55 lb-ft).
  1. Connect the power steering pump supply hose.
  1. Install the power steering pump supply hose bracket bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the pressure line bracket-to-engine bolt.
    • Tighten to 11 Nm (97 lb-in).
  1. Install the power steering pump pulley. For additional information, refer to Power Steering Pump Pulley - 4.0Lin this section.
  1. Fill the power steering system. For additional information, refer to Section 211-00.

Apr 13, 2016 | Ford Cars & Trucks

1 Answer

Need instructions for power steering pump replacement on a 1992 pontiac trans sport. FAST PLEASE!!! has a 3.8L engine with a/c. thankyou for your help!


-- from the 1990-1999 Lumina / Silhouette / TranSport Repair manual ---

1992 Pontiac TransPort Power Steering Pump REMOVAL AND INSTALLATION

  1. Disconnect the negative battery cable.
  2. Disconnect and cap the power steering pump hoses.
  3. Remove the accessory drive belt.
  4. Remove the power steering pump pulley using a suitable puller tool.
  5. Remove the pump mounting bolts and remove the pump from the vehicle.

See Figures 1, 2 and 3


0900c152801dbcf7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: On some vehicles, you must use a puller to remove the power steering pump pulley


0900c152801dbcf8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Power steering pump mounting-early model vehicle shown


0900c152801dbcf9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Power steering pump mounting-late model vehicle shown

  1. Installation is the reverse of the removal procedure. Tighten the pump mounting bolts to 18 ft. lbs. (25 Nm).
  2. Bleed the power steering system to remove trapped air. Air in the system could cause noise and or damage to the pump.

BLEEDING

This procedure requires the help of an assistant.
  1. With the engine OFF, the wheels off the ground and turned all the way to the left, fill the fluid reservoir to the FULL COLD mark on the fluid level indicator.
  2. With an assistant checking the fluid level and condition, bleed the system by turning the wheels from side to side without hitting the stops. You should repeat this at least 20 times, making sure to keep the fluid level at the FULL COLD mark.

Fluid with air in it has a light tan appearance. This air must be eliminated from the fluid before normal steering action can be obtained.
See Figure 4


0900c152801dbcfa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Power steering bleeding procedure

  1. Start the engine, and while it is idling, recheck the fluid level and add as necessary to reach the FULL COLD mark.
  2. Return the wheels to the center position. Lower the front wheels to the ground and continue running the engine for 2 or 3 minutes.
  3. Road test the vehicle to make sure the steering functions properly and is free of noises.

See Figure 5


0900c152801dbcfb.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 5: Torque specificatio

Jan 02, 2011 | Pontiac Trans Sport Cars & Trucks

1 Answer

Replacement steps for power steering pump - orginal one leaking thanks


REMOVAL & INSTALLATION 2.4L Engine Fig. 1: Location of the power steering pump - 2.4L engine 87958079.gif
  1. Disconnect the negative battery cable.
  2. Disconnect and cap the power steering fluid lines from the pump.
  3. Remove the mounting bolts, then remove the power steering pump. To install:
  4. Install the power steering pump.
  5. Install the pump mounting bolts and tighten to 22 ft. lbs. (30 Nm).
  6. Uncap and connect the fluid lines to the power steering pump. Tighten the line fittings to 20 ft. lbs. (27 Nm).
  7. Connect the negative battery cable.
  8. Fill the power steering pump with fluid and bleed the air from the system.
  9. Road test the vehicle and verify no leaks.
3.1 Engine Fig. 2: Power steering pump mounting detail - 3.1L engine 86888066.gif
  1. Disconnect the negative battery cable.
  2. Remove the serpentine drive belt.
  3. Unfasten the power steering pump-to-engine bolts.
  4. Pull the pump forward, then disconnect and plug the pressure tubes. NOTE: Place a rag under the pressure tubes to contain any excess power steering fluid.
  5. Remove the engine mount, and remove the pump. NOTE: To remove the engine mount, support the engine with a suitable jack by the oil pan. Make sure to use a thin piece of wood on the jack pad to disperse the weight and prevent oil pan damage. To install:
  6. Position the pump and install the engine mount. Tighten the engine support-to-mount bolts to 96 ft. lbs. (130 Nm). Tighten the engine mount-to-body bolts to 49 ft. lbs. (66 Nm) and the nut to 31 ft. lbs. (42 Nm), and remove the jack from the oil pan.
  7. Unplug and connect the pressure tubes.
  8. Install the serpentine drive belt.
  9. Fill the power steering pump reservoir with the proper type and amount of fluid. Bleed the power steering system.
  10. Connect the negative battery cable and check for leaks.
prev.gif next.gif

Nov 20, 2010 | 1999 Chevrolet Malibu

1 Answer

Cant find were to put powersteering fluid


Power Steering Pump Removal & Installation 3.8L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Place a drain pan under the vehicle.
  3. Remove the accessory drive belt from the power steering pump pulley.
  4. Raise and safely support the vehicle.
  5. Remove the right front tire and wheel assembly.
  6. Remove the hoses from the power steering pump.
  7. Remove the mounting bolts and the power steering pump from the engine.
  8. Remove the reservoir and pulley from the pump if necessary.
To Install:
Power steering pump removal/installation (3.8L engine) gm-08-38-480.gif

  1. If removed, install the power steering pump reservoir and pulley on the power steering pump.
  2. Position the power steering pump to the engine and install the mounting bolts. Tighten the bolts to 25 lb ft (34 Nm).
  3. Install the pressure and return hoses to the pump.
  4. Install the right front tire and wheel assembly.
  5. Lower the vehicle.
  6. Install the accessory drive belt.
  7. Fill and bleed the power steering system.
  8. Inspect the system for leaks.
  9. Remove the drain pan from under the power steering pump area.
3.4L Engine To Remove:
  1. Place a drain pan under the power steering pump.
  2. Remove the coolant reservoir.
  3. Remove the pulley from the power steering pump.
  4. Remove the wiring harness near the power steering pump and place it out of the way.
  5. Disconnect the fluid hoses from the power steering pump.
  6. Remove the mounting bolts from the power steering pump and remove the pump.
To Install:
Power steering pump removal/installation (3.4L engine) 88008g71.gif

  1. Position the power steering pump assembly to the engine and install the mounting bolts. Tighten the mounting bolts to 25 lb ft (34 Nm).
  2. Install the wiring harness in its original position.
  3. Install the pulley on the power steering pump.
  4. Install the coolant reservoir.
  5. Fill and bleed the power steering system.
  6. Inspect the system for leaks.
  7. Remove the drain pan from under the power steering pump.
prev.gif next.gif

Sep 18, 2010 | 2000 Chevrolet Impala

1 Answer

Removing power steering pump from v8 windsor


Section 11-02A: Steering Pump, Power, C-II 1996 Aerostar, Ranger and Explorer Vehicles Workshop Manual REMOVAL AND INSTALLATION Pump and Pulley SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Steering Pump Pulley Remover T69L-10300-B Steering Pump Pulley Replacer T65P-3A733-C
Removal
  1. Disconnect the power steering return hose (3A713) at the pump and drain fluid.
  1. Remove the power steering pressure hose (3A719) by unscrewing connector from the pump.
  1. On the Aerostar 3.0L V-6 engine (6007), loosen the drive belt tensioner (6B209) and adjustment bolts.





    Item Part Number Description 1 10346 Generator 2 8501 Water Pump 3 8678 Belt Idler Pulley 4 3A733 Power Steering Pump Pulley 5 6303 Crankshaft 6 2884 A/C Clutch 7 — Without A/C On the 2.3L I-4 and 4.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a counterclockwise direction. On Ranger 3.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a clockwise direction. Remove drive belt (8620) from under drive belt tensioner and slowly lower pulley to stop. Remove the drive belt from the power steering pump pulley (3A733).





    Item Part Number Description 1 10346 Generator 2 2884 A/C Clutch 3 3A733 Power Steering Pump Pulley 4 8501 Water Pump 5 6303 Crankshaft 6 8678 Belt Idler Pulley 7 6B209 Drive Belt Tensioner
  1. NOTE: If the drive belt requires servicing, refer to Section 03-05 .

    Remove the drive belt from the power steering pump pulley.
  1. Remove the oil dipstick tube.
  1. Remove the power steering pump support (3C511).
  1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley.
  1. NOTE: Do not apply pressure on the power steering pump rotor shaft (3B559). Pressure will damage internal thrust areas of the power steering pump (3A674).

    While holding the remover tool nut stationary with a wrench, rotate the inner spindle of the remover tool clockwise until the pulley is pulled off the power steering pump rotor shaft.
  1. Remove the bolts attaching the power steering pump to the A/C compressor mounting bracket (2882).
Installation
  1. Install the power steering pump on the A/C compressor mounting bracket. Install and tighten attaching bolts to 41-61 Nm (30-45 lb-ft). On 4.0L engine, tighten to 47-64 Nm (35-47 lb-ft).
  1. Position the support on the A/C compressor mounting bracket. Install mounting bolts and tighten to 47-64 Nm (35-47 lb-ft).
  1. NOTE: Fore/aft location of power steering pump pulley on power steering pump rotor shaft is critical. Incorrect belt alignment may cause drive belt squeal or chirp. Make sure pull-off groove on power steering pump pulley is facing front and flush with end of shaft ± 0.254mm (± 0.010 inch).

    Install the Steering Pump Pulley Replacer T65P-3A733-C and install the power steering pump pulley.
  1. Install the drive belt on the power steering pump pulley.
  1. On the 2.3L I-4, Ranger 3.0L V-6, and 4.0L V-6 engines, position and rotate drive belt on engine. While lifting drive belt tensioner in a counterclockwise direction (clockwise on Ranger 3.0L V-6), slide drive belt under drive belt tensioner and lower drive belt tensioner to drive belt.
    On Aerostar 3.0L V-6 engine, position the belt idler pulley (8678) assembly to give the drive belt the tension specified. Refer to belt tension check in Section 03-05 . Tighten the drive belt tensioner and adjustment bolts to 47-64 Nm (35-47 lb-ft).
  1. Install the power steering pump support, if removed.
  1. Install the oil dipstick tube.
  1. Install the pressure hose tube nut and new Teflon® wagner into power steering pump valve outlet fitting (3D654) and tighten to 41-54 Nm (30-40 lb-ft).
  1. Connect the power steering return hose to the power steering pump, and reposition the clamp.
  1. Fill the power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent fluid meeting specification ESW-M2C33-F. Start the engine and turn the steering wheel (3600) from left to right without hitting stops to remove air from the system.
  1. Check for leaks and recheck the fluid level. Add fluid if necessary to proper level as specified in Section 11-00 .


    Power Steering Pump and Power Steering Pulley, 2.3L TPH Engine, Ranger Only





    Item Part Number Description 1 2882 A/C Compressor Mounting Bracket 2 N606543-S2 Bolt (2 Req'd) 3 N606069-S2 Bolt (2 Req'd) 4 N605803-S2 Bolt 5 N800199-S8M Screw 6 3D673 Power Steering Pump Pulley 7 3F671 Power Steering Belt Idler Support 8 N806020-S2 Bolt 9 3A674 Power Steering Pump 10 19703 A/C Compressor A — Tighten to 21.2-29 Nm (16-21 Lb-Ft) B — Tighten to 40.3-55 Nm (30-41 Lb-Ft) C — Tighten to 44-51 Nm
    (32-38 Lb-Ft)

    Power Steering Pump and Power Steering Pulley, 3.0L Engine, Aerostar





    Item Part Number Description 1 3A674 Power Steering Pump 2 3C511 Power Steering Pump Support 3 6007 Engine 4 N803564 Stud 5 N802827-S2 Nut 6 N800199-S8M Screw (3 Req'd) 7 N8011179-S2 Screw (3 Req'd) 8

Jun 09, 2010 | 1996 Ford Explorer

2 Answers

92 dodge ram cummins power steering?


Yes they have power steering.

Apr 22, 2010 | 1992 Dodge Ram 250

1 Answer

How do i remove the power steering pump on a 1992 buick oldsmobile ninety eight regency elite???


Remove the belt, Remove the 2 bolts that hold the pump to the engine by using a socket and extension through the hole in the pump pulley. Remaove the 2 hoses. you may have to pull the pump out through the wheel well.

Jul 17, 2009 | 1992 Oldsmobile Ninety Eight

1 Answer

I broke timing belt when replacing hormonic balancer


Here are some. Hope it helps =D

Timing Marks

Diagram


TORQUE SPECIFICATIONS
Application Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt 37 (50)
Alternator Bracket Adjuster Bolt 16 (22)
Alternator Bracket Bolt 33 (45)
Balance Shaft Pulley Bolt 22 (30)
Camshaft Pulley Bolt
2.2L DOHC 37 (51)
2.2L SOHC & 2.3L 27 (37)
Crankshaft Pulley Bolt 184 (250)
Power Steering Belt Adjuster Nut 11 (15)
Power Steering Pump Bracket Bolt 33 (45)
Power Steering Pump Mounting Bolt 16 (22)
Shift Cable Bracket Bolt 16 (22)
Timing Belt Tension Adjuster 33 (45)
INCH Lbs. (N.m)
Timing Belt Cover Bolt 108 (12)
Valve Cover Nut 90 (10)
Water Pump Bolt 108 (12)

Jun 28, 2009 | 1992 Honda Accord

1 Answer

Inatallation 92 honda accord power steering pump


Hey, here's the procedure, disable air bag, if equipped w/ one, disconnect the pump return hose from the reservoir and place the end in a large container. Plug the port in the reservoir. Start the engine and turn the steering wheel lock to lock several times, until fluid stops running from the hose. Turn off engine immediately. Re-attach hose. Disconnect the inlet and outlet hoses at the pump. Remove the drive belt. Remove the mounting bolts/nuts and remove pump.
Install in reverse order. Adjust belt tension,fill ps reservoir and bleed any air from the system (to bleed air from system, fill reservoir, start engine and allow to idle, turn wheel from side to side all the way several times. Shut off, fill if necessary.
. Tighten bolts to : Thru bolt 30 ft lbs., mounting nut 16 ft lbs.

Dec 26, 2008 | 1992 Honda Accord

1 Answer

Replacing power steering pump 1992 ford tempo


take the belt off.
disconnect the hoses connected to it.
remove the bolts holding the pump.
remove and replace the pump
be sure that you tighten up well the bolts holding the new pump
connect the hoses
put the belt on
refill the pump
turn vehicle on " keep the pump's cap off
refill as needed while turning the wheel from one side to another
" do not overfill, watch out the level marks"
tighten the pump's cap on
ready to roll

May 14, 2008 | 1992 Ford Tempo

Not finding what you are looking for?
1997 Pontiac Grand Am Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...