Question about 1992 Ford Explorer

1 Answer

What is the best way to remove the three top bolts on ****** on a 1992 explorer? i can't seem to get to them.

Changing flywheel. Or trying to , lol

Posted by on

  • hensonfam423
    hensonfam423 Feb 12, 2012

    Will try. Thank you

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Ford Master
  • 2,007 Answers

From underneath. Use a long 3/8 s drive extension and a universal joint or a universal socket on the end. You can make it as long as you need. 3 or 4 feet if necessary. You may need someone to guide it to the bolts from up top while you work underneath.

Posted on Feb 12, 2012

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: I need the torque specs. for flywheel mount bolts

i guess is 85 lbs /foot

Posted on Oct 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the shifter in a 1992 ford explorer


you will have to remove the area around the shift lever inside the car to be able to get to the 4 bolts that hold the gear lever into the top of the box (turret bolts). Undo the bolts and lift the assembly off the top of the box . Stuff rags into the hole to prevent dirt from under the car getting into the top of the box

Aug 31, 2014 | 1992 Ford Explorer

1 Answer

How to remove bolts out of 2003 for removal of transmission


If you are talking about the two bolts on top of the bell housing. You will need a three foot extension with a swivel and 15 mm socket. To access the top bolts you need to put your jack with a piece of wood under the transmission pan, jack it up just enough so you can remove the rear cross member then slowly lower your jack supporting the trans. Until you see those top bolts approx. Three inches assuming you have removed all the other bolts on bell housing and the three bolts that attach the flywheel to the pumpkin.

Apr 25, 2014 | 2004 Chevrolet TrailBlazer

1 Answer

Flywheel removing


the simplest way to remove a flywheel is to use an impact gun. To re-tension the flywheel place a gear box bolt in a hole and use a large flat bladed screw driver in the teeth and under the bolt against the turn of the bolt. Some flywheels seem stuck on as they are positioned on a dowel so a hit on the front side will jar them loose.

Dec 29, 2013 | 2003 Ford Explorer

1 Answer

Need advise on removing the top mounting bolt on a starter of a 1998 ford explorer


Hi Jcetkt, Make sure the park brake is fully engaged. Chock the wheels and prepare a long extension with the correct size socket spanner, (A box wrench set onto a long extension) Slide under the vehicle and loosen it from the bottom. It may be a good idea to have a pal guiding the wrench from top side. Regards John

Feb 23, 2012 | 1998 Ford Explorer

1 Answer

Trying to remove transmission on 94 chevy 1500 pickup, got all the scews out but still seems to be stuck. any suggestions on its removal


Did you remove the bolts connecting the flywheel to the torque converter? The converter
slides back off the motor along with the transmission for most GM's.
Also there should be two alignment dowels which protrude approximately 3/4 inch off
the back of the block. After making sure the flywheel is disconnected, usually you can
rock the transmission (secured to a transmission jack of course) side to side to break it
free. If you need to unbolt the torque converter you can rotate the engine with a
breaker bar on the crankshaft pulley bolt. Hope this helps.

May 07, 2011 | 1992 Chevrolet K1500

2 Answers

How do i change a flywheel on a 1993 chevrolet k1500 pickup


remove trans bolts and slide trans back to gatn acces to fly wheel bolts u dont have to fully remove the trans.

Aug 23, 2010 | 1992 Chevrolet K1500

2 Answers

Cannot remove transmission


Did you remove the torque converter bolt's from the fly wheel, should be 4. You will have to turn the motor by hand to remove all the bolt's.

Jul 22, 2010 | 1999 Ford Escort

1 Answer

Change starter 192 buick roadmaster


dissconect battery, remove flywheel cover,remove 2 bolts holding starter, now drop starter and remove wiring and take out,

Sep 30, 2009 | 1992 Buick Roadmaster

1 Answer

Hello Friend, I have a Dodge Caravan 1997 and in the process of changing out my water pump and timing belt. I am in the stage where I need to open the damper harmonic bolt. Which direction does this bolt...


I have managed to open the harmonic damper bolt. This bolt opens in the counter clockwise rotation. A breaker bar was used with the flywheel locked in place. In order to get to the flywheel, the starter motor was removed to get access. The manual suggest removing the bell housing plate. This takes more effort and one of side engine mount also need removal. I decided to remove the starter motor instead. In order to remove the starter motor, first remove the cables from the starter motor and three mounting bolts. Secure a rod or a screw driver between the flywheel and bell housing through a hole in the flywheel. The size of the size is about 1/2". This hole was visible when the engine is set to TDC (top dead center). There could be more than one hole but I did not try to rotate the engine to find out. Once the rod or the screw driver in place in the flywheel, use the 22mm socket head and breaker bar and undo the harmonic damper bolt counter clockwise (CCW). I believe an impact air gun could do this job as well. The spec on the bolt is 100 ft lbs torque - Hendry

Jan 13, 2009 | 1993 Dodge Caravan

2 Answers

95 buick lesabre starter removal


you have two bolts. the plastic cover will need to come off should be two or three 10mm bolts holding it

Nov 06, 2008 | 1993 Buick LeSabre

Not finding what you are looking for?
1992 Ford Explorer Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...