Question about Cars & Trucks

Open Question

How do I assemble stiffel floor lamp

The floor lamp is turned on/off by moving the pole.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The gear shifter on my 1998 Pontiac SE coupe will not unlock so I can take the car out of park


Do you have column or floor shifter ?
All automatic transaxle models use an electric park lock system. Within the housing assembly, a lock cylinder is connected to an actuator which rotates and engages on the electric park lock solenoid. When the floor-shift lever is not in the park position, the actuator disengages from the electric park lock solenoid slider. This allows the lock cylinder to move to the lock position. With the shift lever in PARK and the lock cylinder in LOCK, the actuator cam is positioned against the electric park lock solenoid slider. This prevents the shift lever from shifting out of the PARK position.
The column-shift automatic transaxle model uses a flexible cable actuator instead of an electric park lock system. One end of the cable is attached to the gate assembly. The other end of the cable is attached to the column mounted housing assembly. This system functions similarly to the floor-shift ignition lock system.
The manual transaxle model uses a push button lock cylinder. A clutch start switch is used. The clutch pedal must be pressed before the engine will crank. Refer to Park Lock System Check .
CAN you turn the key on ?
The gear selector does not shift out of PARK with the brake pedal depressed and the ignition switch in RUN.
Automatic Transmission Shift Lock Control Always On with Ignition in Run
Action
Value(s)
Yes
No

1

Was the BTSI System Check performed?
--
Go to Step 2
Go to Automatic Transmission Shift Lock Control System Check

2

Is this a column shift vehicle?
--
Go to Step 3 yes
Go to Step 4 no

3

  1. Move the gear selector to the PARK position.
  2. Disconnect the automatic transaxle control connector
  3. Turn the ignition switch to RUN.
  4. Connect the test lamp between terminal B and ground.
Does the test lamp light?
--
Go to Step 4
Go to Step 8

4

  1. Disconnect the brake switch connector C2.
  2. Move the ignition switch to RUN.
Can you shift the transaxle out of the PARK position?
--
Go to Step 5
Go to Step 8

5

Is the brake switch adjusted properly?
--
Go to Step 6
Go to Step 7

6

Replace the brake switch.
Is the repair complete?
--
System OK
--

7

Adjust the brake switch.
Is the repair complete?
--
System OK
--

8

  1. Disconnect the BTSI solenoid connector (column shift vehicles) or disconnect the automatic transaxle control connector (console shift vehicles).
  2. Move the ignition switch to RUN.
Can you shift the transaxle out of the PARK position?
--
Go to Step 9
Go to Step 10

9

Repair the short to power in CKT 1135.
Is the repair complete?
--
System OK
--

10

Test for sticking or binding in the shift linkage.
Does the shift linkage stick or bind?
--
Go to Step 11
Go to Step 12

11

Repair the shift linkage.
Is the repair complete?
--
System OK
--

12

Replace the BTSI solenoid (column shift vehicles) or replace the automatic transaxle control (console shift vehicles).
Is the repair complete?
--
System OK
Go to Step 1

May 18, 2015 | Pontiac Cars & Trucks

1 Answer

How to change a front turn light in a 1996 taurus.


Lamps, Parking Front Lamp-Lamp Assembly, Taurus
Removal and Installation
  1. Remove Headlamp (13008) as outlined.
Headlamp Assembly
Removal and Installation
  1. ani_caut.gif WARNING: THE REPLACEABLE HALOGEN HEADLAMP BULB CONTAINS GAS UNDER PRESSURE. THE HALOGEN HEADLAMP BULB MAY SHATTER IF THE GLASS ENVELOPE IS SCRATCHED OR THE HALOGEN HEADLAMP BULB IS DROPPED. HANDLE HALOGEN HEADLAMP BULB CAREFULLY. GRASP HALOGEN HEADLAMP BULB ONLY BY ITS PLASTIC BASE. AVOID TOUCHING GLASS ENVELOPE. KEEP HALOGEN HEADLAMP BULB OUT OF REACH OF CHILDREN.
    Position headlamp switch (11654) and headlamp time delay switch (13736) in the OFF position.
  1. Remove two bolts retaining headlamp (13008) to upper support assembly and loosen pinch bolt. Remove headlamp assembly from vehicle.
  1. Remove park lamp bulb and socket (Sable only) and headlamp bulb and socket from Headlamp Assembly as outlined.


    Headlamp Assembly (Taurus Shown, Sable Similar)


    k24744a.gif
  1. Turn lamp socket and wiring (13410) assembly 1/2 turn counterclockwise and remove from parking lamp (13200) housing.
  1. Remove screw from park/turn signal housing.
  1. Using 1/4 inch drive socket extension and swivel, insert tool through two access holes in upper radiator support. Remove screws from park/turn signal housing.
  1. Remove parking lamp from vehicle.
  1. To install, reverse Removal procedure.


    Front Lamp-Lamp Assembly, Taurus


    k23818a.gif

Nov 19, 2010 | Ford Taurus Cars & Trucks

1 Answer

Replace a brake light


COUPE The side marker lights for the SC and SC2 are part of the turn signal/parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. Rear Turn Signal, Brake and Parking Lights EXCEPT WAGON
  1. Disconnect the negative battery cable. Fig. 5: Remove the trim panel fasteners - except wagon 84196109.jpg
    Fig. 6: Carefully remove the trim panel - except wagon 84196110.jpg
    Fig. 7: Pull the lamp assembly straight back and out of the opening 84196111.jpg

  2. Remove the trim panel fasteners, then carefully remove the trim panel.
  3. Remove the 2 retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  4. Tilt the assembly downward for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  5. Installation is the reverse of removal. Fig. 8: Tilt the assembly downward for access to the sockets 84196112.jpg
    Fig. 9: Twist and remove the socket and bulb from the lamp assembly 84196113.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Remove the retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  3. Tilt the assembly for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  4. Installation is the reverse of removal. Fig. 10: Exploded view of the tail lamp assembly - wagon 84196114.gif
High-Mount Brake Light EXCEPT WAGON
  1. Disconnect the negative battery cable.
  2. Open the trunk for access to the lamps.
  3. Locate the bulbs at the rear underside of the trunk lid. Remove the bulb(s) by twisting, then pulling straight out.
  4. Installation is the reverse of the removal. Fig. 11: Remove the high-mount brake light by twisting its socket 1?4 turn counterclockwise - except wagon 84196115.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Raise the liftgate, then remove the wedge blocks from each side of the liftgate assembly.
  3. Remove the lower fasteners from the liftgate lower trim panel, by pushing in the center of each pin approximately 1?8 in. until it clicks, then remove the fastener.
  4. Insert a screwdriver or small prybar into the hole in the lower trim panel (located near the wiper pivot on the pivot hump) so that the tool sits on top of the pivot. Lift up on the tool handle to disengage the trim panel upper clips, then remove the lower trim panel from the vehicle.
  5. Unplug the high-mount brake light wiring harness.
  6. Remove the brake light fasteners, then remove the lamp assembly from the liftgate.
  7. To remove the bulb(s), push slightly on the top edge of the lens and rotate it away from the housing. Remove the bulb(s) from the housing. To install:
  8. In order to prevent the possibility of water leaks into the liftgate, inspect the lamp gasket for damage and replace, if necessary.
  9. If removed, install the bulb(s) by inserting the bottom edge of the lens into the housing and snapping it into place.
  10. Position the lamp into the liftgate and tighten the fasteners to 35 inch lbs. (4 Nm).
  11. Connect the wiring harness to the lamp assembly.
  12. Align the upper clips on the lower trim panel to the liftgate slots, then install the panel by pushing at the clip locations.
  13. Reset the trim panel push-in fasteners by spreading the center pin tabs and moving the pin so that it sits approximately 1?4 in. out of the fastener. Insert the fasteners into the bottom of the trim panel and push the center pin until flush.
  14. Install the liftgate wedge blocks.
  15. Connect the negative battery cable and check for proper lamp operation. Fig. 12: Removing the liftgate lower trim panel assembly - wagon 84196116.gif
    Fig. 13: Exploded view of the high-mount brake light bulb and lens assembly - wagon 84196117.gif

Nov 04, 2010 | 1998 Saturn SL

1 Answer

I need to replace rear tail light bulbs on 1996 Saturn SL1


COUPE The side marker lights for the SC and SC2 are part of the turn signal/parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. Rear Turn Signal, Brake and Parking Lights EXCEPT WAGON
  1. Disconnect the negative battery cable. Fig. 5: Remove the trim panel fasteners - except wagon 84196109.jpg
    Fig. 6: Carefully remove the trim panel - except wagon 84196110.jpg
    Fig. 7: Pull the lamp assembly straight back and out of the opening 84196111.jpg

  2. Remove the trim panel fasteners, then carefully remove the trim panel.
  3. Remove the 2 retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  4. Tilt the assembly downward for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  5. Installation is the reverse of removal. Fig. 8: Tilt the assembly downward for access to the sockets 84196112.jpg
    Fig. 9: Twist and remove the socket and bulb from the lamp assembly 84196113.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Remove the retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  3. Tilt the assembly for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  4. Installation is the reverse of removal. Fig. 10: Exploded view of the tail lamp assembly - wagon 84196114.gif
High-Mount Brake Light EXCEPT WAGON
  1. Disconnect the negative battery cable.
  2. Open the trunk for access to the lamps.
  3. Locate the bulbs at the rear underside of the trunk lid. Remove the bulb(s) by twisting, then pulling straight out.
  4. Installation is the reverse of the removal. Fig. 11: Remove the high-mount brake light by twisting its socket 1?4 turn counterclockwise - except wagon 84196115.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Raise the liftgate, then remove the wedge blocks from each side of the liftgate assembly.
  3. Remove the lower fasteners from the liftgate lower trim panel, by pushing in the center of each pin approximately 1?8 in. until it clicks, then remove the fastener.
  4. Insert a screwdriver or small prybar into the hole in the lower trim panel (located near the wiper pivot on the pivot hump) so that the tool sits on top of the pivot. Lift up on the tool handle to disengage the trim panel upper clips, then remove the lower trim panel from the vehicle.
  5. Unplug the high-mount brake light wiring harness.
  6. Remove the brake light fasteners, then remove the lamp assembly from the liftgate.
  7. To remove the bulb(s), push slightly on the top edge of the lens and rotate it away from the housing. Remove the bulb(s) from the housing. To install:
  8. In order to prevent the possibility of water leaks into the liftgate, inspect the lamp gasket for damage and replace, if necessary.
  9. If removed, install the bulb(s) by inserting the bottom edge of the lens into the housing and snapping it into place.
  10. Position the lamp into the liftgate and tighten the fasteners to 35 inch lbs. (4 Nm).
  11. Connect the wiring harness to the lamp assembly.
  12. Align the upper clips on the lower trim panel to the liftgate slots, then install the panel by pushing at the clip locations.
  13. Reset the trim panel push-in fasteners by spreading the center pin tabs and moving the pin so that it sits approximately 1?4 in. out of the fastener. Insert the fasteners into the bottom of the trim panel and push the center pin until flush.
  14. Install the liftgate wedge blocks.
  15. Connect the negative battery cable and check for proper lamp operation. Fig. 12: Removing the liftgate lower trim panel assembly - wagon 84196116.gif
    Fig. 13: Exploded view of the high-mount brake light bulb and lens assembly - wagon 84196117.gif
Reverse Light EXCEPT 1991-96 COUPE For the Saturn wagons and sedans, the reverse lamp is part of the rear turn signal, brake and parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. 1991-96 COUPE
  1. Disconnect the negative battery cable.
  2. Reach behind the bumper bar and disconnect the harness and socket from the reverse lamp. Remove the bulb from the socket.
  3. If necessary, unfasten the retaining nuts and remove the lamp from the bumper bar.
  4. Installation is the reverse of the removal. Fig. 14: Exploded view of the reverse lamp mounting - 1991-96 coupe 84196118.gif

Oct 23, 2010 | 1996 Saturn SL

1 Answer

What do I need to unscrew in the trunk to change the reverse light in my 01 chevy impala


Tail Lamp Assembly Removal & Installation To Remove:
  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.
  8. Remove the side marker lamp socket by turning counterclockwise.
To Install:
  1. Install the side marker lamp socket by turning clockwise.
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
prev.gif next.gif

Oct 18, 2010 | 2001 Chevrolet Impala

1 Answer

How do i change right turn lamp in my 2004 pontiac grand prix


Answer remove the headlight assembly and the bulbs are located below the Assembly to remove headlamp assembly and access signals: -open the hood
-while pushing rearward on the headlamp,pull up half-way on the (white)plastic retaining clip on the electrical connector - align the square cut-out on the retaining clip with the notch on the headlamp
-pull the headlamp assembly straight out from the vehicle (moving the headlamp up and down slightly may help with its removal)
-locate the front turn signal,parking lamp and foglamp bulbs which are located below the headlamp assembly (turn/parking lamp on top and the fog lamp is below it)
-turn the bulb socket 1/4 turn counterclockwise to remove it from assembly
-pull the old bulb from the socket and replace it with a new one
-turn the bulb socket a 1/4 turn clockwise to reinstall it
-reinstall the headlamp assembly carefully so you dont scratch the paint
-push down on (white)plastic retaining clip on the electrical connector while pushing rearward on the headlamp making sure headlamp is secure.

Nov 26, 2009 | 2004 Pontiac Grand Prix

1 Answer

How to change 4 runner front blinker light. there's a phillips screw under the hood I have removed but there is another fastener in the lower portion of the blinker housing I cannot locate.


Remove or disconnect the following:
  • Connector
  • Screw
  • Claw fitting
  • Front turn signal lamp assembly
  • Front turn signal lamp plug assembly
  • Front turn signal lamp bulb as shown
6191f4c.gif
c741133.gif
To Install:
  1. Install or connect the following:
    • Front turn signal lamp bulb
    • Front turn signal lamp plug assembly
    • Front turn signal lamp assembly with screw
    • Connector

Oct 01, 2009 | 2004 Toyota 4Runner

1 Answer

How do I replace a taillight lens on a 1991 Geo Storm?


Rear Turn Signal, Brake and Parking Lights


STORM COUPE
  1. Disconnect the negative battery cable.
  2. Lift the luggage compartment floor carpet toward the front of the vehicle and remove the spare tire cover panel.
  3. Remove the ten plastic retaining clips from the rear end trim panel.
  4. Disconnect the luggage compartment lamp electrical connector.
  5. Remove the luggage compartment trim panel and the rear end trim panel.
  6. Disconnect the rear combination lamp assembly electrical connector. Fig. 1: Rear Turn Signal, Brake and Parking Lights — Storm
84256028.gif
  1. Remove the seven nuts and the rear combination lamp assembly from the vehicle.
  2. Disconnect the rear combination lamp electrical connector.
  3. Remove the four bulb sockets from the rear combination lamp assembly and remove the four bulbs from the sockets. To install:
  4. Install the four bulbs to the sockets and install the four bulb sockets to the rear combination lamp assembly.
  5. Connect the rear combination lamp electrical connector.
  6. Install the rear combination lamp assembly to the vehicle and the seven nuts.
  7. Connect the rear combination lamp assembly electrical connector.
  8. Install the rear end trim panel and the luggage compartment trim panel.
  9. Connect the luggage compartment lamp electrical connector.
  10. Install the ten plastic retaining clips to the rear end trim panel.
  11. Install the spare tire cover panel and the luggage compartment floor carpet.
  12. Connect the negative battery cable.

Mar 21, 2009 | 1991 Geo Storm

1 Answer

I need to locate the 4 wheel drive control module on a 2002 Chevy Silverado. can you tell me where to look


  1. Remove the IP trim bezel.
  2. Pull out the lamp switch, 4WD shift buttons, cargo lamp and air deflector louver assembly in order to disconnect the electrical connectors.
  3. Disconnect all the electrical connectors from the lamp switch, cargo lamp and 4WD shift buttons assembly.
  4. Remove the lamp switch, 4WD shift buttons, cargo lamp and air deflector louver assembly from the vehicle
  5. Remove the electrical harness retainer from the IP support beam.
  6. Disconnect the 2 electrical connectors from the transfer case shift control module.
  7. Move the electrical harness to the left side in order to make room to turn the transfer case shift control module.
  8. Rotate the transfer case shift control module about 45 degrees counter clockwise while pulling out at the same time until the module is approximately 90 degrees from the original position.
  9. Pull out the module from the vehicle

Jan 02, 2009 | 2002 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...