Question about 1994 Toyota Corolla

2 Answers

Install starter motor on 94 corrolla - 1994 Toyota Corolla

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 444 Answers

Remove/disconnect battery, remove cylinoid wires and power lead from starter cylinoid (starter cylinoid is located/attached directly on top of the starter, the starter is located on the transmission bellhousing) once the wires have been removed(be sure to note which ones go where, if you have a camera phone just snap a pic) then remove the mounting bolts from the starter housing,and slide the starter out, installation is reverse of removal

Posted on Feb 12, 2012

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

The starter is located at the rear of the engine
diss connect the pos side of the battery
jack up the car and use jack stands for safety

with a light of flash light look up behind the motor from under the car
you will need a wrench size #12 metric for wire the other wire is just a
clip on

you will need a #14 wrench or socket for the bottom starter bolt

from the top of the engine drivers side look down to the starter bolt
you will need a # 14 wrenck to loosen and a socket #14 with a long extension
move wire harness out of you way just a little so you can get the socket on it have somone help you with this have your helper hold the starter from the bottom while you take out the bolt

when the starter is loose it will come out of that mess if you move to the right and pull the plastic guard to the side a little


Read more: http://wiki.answers.com/Q/How_to_you_remove_a_1994_Toyota_Corolla_starter#ixzz1m8HAzTeW

Posted on Feb 12, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Interchsnge yesrs or other make,/models for Starter in 1994 Toyota Corolla


If it's the 1.6 motor then 94 to 96 corolla take that starter only. But if it's a 1.8 motor then 94 to 97 take that starter and also geo prizm 94 to 97 takes that starter

Aug 15, 2014 | 1994 Toyota Corolla

1 Answer

How to replace a starter on a 94' cutlass


3.1L Engines - 1988-94 VEHICLES
(see Figures 5, 6, 7 and 8)
  1. Remove the air cleaner and duct assembly.
  2. Disconnect the negative battery cable.
  3. Raise and safely support the vehicle.
  4. If equipped with an engine oil cooler, drain the engine oil, remove the oil filter and position the hose next to the starter motor to the side.
  5. Remove the nut from the brace at the air conditioning compressor, nut from the brace at the engine and the brace.
  6. Unfasten the retaining bolts, then remove the flywheel inspection cover.
zjlimited_919.jpg

Fig. 5: Unfasten the retaining bolts ...

zjlimited_920.jpg

Fig. 6: ... then remove the flywheel cover

  1. Remove the starter bolts and shims, if equipped. Do not let the starter hang from the starter wires.

zjlimited_921.jpg



Fig. 7: An extension may be needed to access the starter mounting bolts

zjlimited_922.jpg

Fig. 8: Remove the starter motor and any shims that may have been used

  1. Detach the starter wires from the solenoid, then remove the starter from the vehicle.
To install:
  1. While supporting the starter, connect the starter wires at the solenoid.
  2. Install the starter motor-to-engine mount with the shims, if equipped, and the mounting bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  3. If equipped with an engine oil cooler, reposition the hose next to the starter motor, install the oil filter and refill the engine with the proper amount of engine oil.
  4. Install the flywheel inspection cover and tighten the bolts.
  5. Install the starter support brace to the air conditioning compressor and tighten the nut to 23 ft. lbs. (31 Nm).
  6. Carefully lower the vehicle, then connect the negative battery cable.
  7. Install the air cleaner and duct assembly.

Hope helps.

Mar 23, 2011 | 1994 Oldsmobile Cutlass Supreme

1 Answer

How to put the Starter in a Eagle Talon 1991.


from autozone.com


REMOVAL & INSTALLATION
See Figures 5, 6, 7, 8, 9 and 10

  1. Disconnect the negative, then the positive battery cables from the battery.
  2. For 1990-94 vehicles, remove the battery and battery tray from the engine compartment.
  3. For 1990-94 vehicles, detach the speedometer cable connector from the transaxle.
  4. For 1995-98 2.0L turbo engines, remove the air hose.
  5. For 1995-98 2.4L engines, remove the air cleaner and air intake hose.
  6. If equipped with 1.8L engine, remove the bracket on the lower side if the intake manifold.
  7. Detach the starter motor electrical connections.
6f8c23b.gif

Fig. Fig. 5: Exploded view of the starter motor and related components-1990-94 vehicles, others similar


458b681.gif

Fig. Fig. 6: Unfasten the BAT terminal connector from the starter motor


05a1691.gif

Fig. Fig. 7: Unplug the starter motor electrical connector

  1. Unfasten the starter motor mounting bolts, then remove the starter from the vehicle.
d0adab9.gif

Fig. Fig. 8: Unfasten the starter mounting bolts
d00c214.gif

Fig. Fig. 9: Remove all of the starter mounting bolts ...
c92a470.gif

Fig. Fig. 10: ... then remove the starter motor from the vehicle
To install:

  1. Clean both surfaces of starter motor flange and rear plate. Install the starter motor onto the engine and secure with the retainer bolts. Tighten the retainers to the specifications shown in the accompanying figure.
  2. Attach the electrical harness connector(s) to the starter.
  3. If removed, install the intake manifold stay and tighten the retainers to 18 ft. lbs. (25 Nm).
  4. For 1995-98 2.4L engines, install the air cleaner and air intake hose.
  5. For 1995-98 2.0L turbo engines, install the air hose.
  6. For 1990-94 vehicles, attach the speedometer cable to the transaxle. Install the battery tray and battery.
  7. Connect the positive, then the negative battery cables.
Operate the starter to assure proper operation.

Oct 29, 2010 | 1991 Eagle Talon

1 Answer

94 toyota corrolla blows am2 fuse when I try to start


Sounds like the starter is drawing to much current and therefore blowing the fuse. probably needs to be checked by a mechanic

Oct 17, 2010 | 1995 Toyota Corolla

1 Answer

Tools needed to remove starter on 94 dodge spirit 3.0 liter V6


Regular socket wrench set, wrench set, screwdriver, etc.: REMOVAL & INSTALLATION Fig. 1: These three attaching bolts hold the starter motor to the engine/transaxle assembly - all models 86722051.gif
  1. Disconnect the negative (-) battery cable. Raise and safely support the front of the vehicle on jackstands. Remove the engine undercovers, if so equipped.
  2. Remove the 3 bolts attaching the starter to the engine/transaxle. CAUTION
    Be careful when removing the starter motor mounting bolts, the motor can be quite heavy. Personal injury could result if the starter motor falls from its mounting position.
  3. Remove the heat shield and its clamp, if so equipped.
  4. Remove the two electrical wire connector terminal nuts and remove the wiring connector from the starter.
  5. Remove the starter from the vehicle. To install:
  6. Clean all wire terminals of dirt, grease or corrosion.
  7. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 80 inch lbs. (9 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
  8. Install the heat shield if one was removed.
  9. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm) for all vehicles except Premier and Monaco. Tighten the attaching bolts to 20 ft. lbs. (27 Nm) for Premier and Monaco.
  10. Install any undercovers which were removed from the vehicle.
  11. Lower the vehicle.
  12. Connect the negative (-) battery cable. Fig. 2: After disconnecting the starter's electrical wiring, remove the 3 mounting bolts . . . 86722p15.jpg
    Fig. 3: . . . then the starter motor can be lowered from the underside of the vehicle 86722p16.jpg
prev.gif next.gif

Sep 24, 2010 | 1991 Dodge Spirit

1 Answer

Where is the thermostat on a 94 toyota corrolla


The easiest way is to follow the top radiator hose to the motor. Its at the end of the hose ti the aluminum housing. There may be some other hoses coming off the same housing. for one thing it isn't easy to get to. good luck.

Aug 18, 2010 | 1994 Toyota Corolla

1 Answer

How to Remove 94 Ford XLT starter motor & solenoid


  1. Disconnect the negative battery cable.
  2. Raise the front of the vehicle and install jackstands beneath the frame. Firmly apply the parking brake and place blocks in back of the rear wheels.
  3. Tag and disconnect the wiring at the starter.
4. Remove the starter mounting bolts and remove the starter.

To install:

  1. Position the starter motor against the engine and install the mounting bolts. Tighten the mounting bolts to 15-19 ft. lbs. (21-27 Nm).
  2. Install the starter solenoid connector by pushing it straight on. Ensure that the connector locks in position with a notable click.

Install the starter cable nut to the starter solenoid B-terminal. Tighten the nut to 80-123 inch lbs. (9-14 Nm).
  1. Connect any remaining wiring to the starter motor.
  2. Lower the front of the vehicle and remove the wheel blocks.
  3. Connect the negative battery cable.


Mar 31, 2010 | 1994 Ford Ranger Supercab

2 Answers

Changing the starter in a 1994 Toyota Corrolla


you need to remove one bolt from the top and the other from the bottem. also the wires are removed from the bottem. most likey the starter if factory is still good the starter contacts wear out they are under the cover on the back of the starter.

Apr 18, 2009 | 1994 Toyota Corolla

1 Answer

Starter removal 94 explorer


u have to undo the motor mounts put a board under ur oil pan lift ur motor i think its three bolts to the starter

Dec 30, 2008 | 1995 Ford Explorer

1 Answer

My starter


'94 through '97 should share the same starter.

Jun 14, 2008 | 1997 Honda Civic

Not finding what you are looking for?
1994 Toyota Corolla Logo

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...