Question about 1996 Dodge Intrepid

1 Answer

Changing out transmission mount on a 96 dodge intrepid

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Master
  • 444 Answers

This is a fairly easy fix, youll need to undo the mount bolts and with a jack from the bottom or a cherry picker from the top lift up the ****** enough to wiggle the mounts out (or drop the ****** if they are top mount) you may also need need to loosen the motors mounts to allow everything to move as well as remove the half shafts from the transmission to allow movement. depends on how far you need to move it in order to wiggle the mounts out. i always reccomend buying a haynes or chilton repair manual. as it covers step by step how to perform alot of these repairs in simple step by step format (if you can bake a cake by direction then you can work on a car) and they are ussually around 10 to 15 bucks. not a bad investment. hope this helps! good luck

Posted on Feb 12, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Dodge intrepid problems

Have a qualified transmission shop rebuild it be sure to flush your cooler lines flushed before you install the rebuilt trans.

Dec 11, 2013 | Cars & Trucks

1 Answer

How can i replace engine mounts on 94 dodge

grab a block and a jack then place jack under engine or transmission, then put pressure on it, then remove center support bracket on bottom remove mounts install new ones reinstall center bracket line up mounts in bracket tighten center bolts remove jack and block

Mar 15, 2010 | 1994 Dodge Intrepid

2 Answers


It should be on the transmission by the passenger side of car. It has three wires connected to it.
1998 Dodge Intrepid
the crank sensor is on the passenger side of the car on the back of the engine. Check right up there by the transmission housing.
1994 Dodge Intrepid 3.3 liter

Jan 01, 2010 | 1996 Dodge Intrepid

1 Answer

Can't find oxygen sensor bank 2 sensor 1 location in my 96 dodge intrepid.

The O2 sensor on the 3.5L is located towards the rear of the engined mounted in the exhaust manifold.

Jul 07, 2009 | 1996 Dodge Intrepid

1 Answer

I need to change my (Front Strut Mounts) on my 96 Dodge Intrepid 3.3 engine.I just need a link to show me how or know how to do it..

Go to and register for free. Than you can put in your car's information and than you can view a Free Full Online Repair Manual!

May 06, 2009 | 1996 Dodge Intrepid

1 Answer

96 dodge intrepid auto transmission wont shift up from low .

Iv'e ran across this before, Try this.. unhook the postive Battery terminal for a few minutes then replace. I had the same problem with my intrepid years ago and it took care of it and never had a problem with again! Hope this works for You!

Feb 16, 2009 | 1996 Dodge Intrepid

Not finding what you are looking for?
1996 Dodge Intrepid Logo

329 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides