Question about Chevrolet 1500

1 Answer

1998 chevrolet k1500 series cranks but wont start

My avital alarm kept goin off so i disconnected it so it would go off.. then my truck would not start,so i hooked alarm back up but now my truck will turn over and if it starts at all it will die immediately.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 5,522 Answers

Contact AVITAL company. This sounds like the alarm is killing the ignition or fuelpump circuit. Sometimes there is a sequence used in alarm resets and you should know it if you are out in the Boonies without a Cell signal.

Posted on Feb 12, 2012

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 117 Answers

SOURCE: What is the torque specification for the pitman

Pitman shaft nut--- 184 ft. lbs.
Pitman arm-to-relay rod nut--- 46 ft. lbs.

Posted on May 08, 2010

  • 869 Answers

SOURCE: removing and replacing engine from 1998 chevrolet

the model is quite old. u might need to consult a reliable suburban dealer.

Posted on Feb 07, 2011

  • 819 Answers

SOURCE: On a 1998 Chevrolet truck, K1500, 350 engine, I have a dead miss.

if you are getting a CKP (crankshaft position sensor) code, and during you rebuild you had removed the sensor of moved it in any way, you probably need to perform a CKP sensor relearn. check with your local shops, as they need to be set up to do this, but it is not an expensive thing.

Posted on Dec 28, 2009

Testimonial: "Thank you very much for the answer, it will be very helpful when I go to the dealership."

  • 149 Answers

SOURCE: No reverse on Chevrolet 1998 K1500 Silverado

its the gear setting

Posted on May 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I disarm the alarm system on my 1998 volkswagen?It wont start ,cranks but wont run..I changed the plugs still wont start,someone said could be in the alarm system to disarm it.


The alarm would cause the car not to crank, and the alarm horn would sound. You can try unlocking the car from the trunk lock to disarm the alarm. But crank and no start could be a bad ignition switch. Do the dashboard lights stay on or go out while the key is in the crank position? They should remain "on". Worn ignition switch could cause the car to crank but not start.

May 04, 2017 | Volkswagen Cars & Trucks

1 Answer

My alarm refuse to cut off


When starting my truck it sometimes make a humming sound.

Feb 12, 2014 | 2002 GMC Yukon Denali

1 Answer

98 K1500 4X4 5.7 - CRANK, NO START, FUEL SAMPLE IS CLEAN, PRESSURE SEEMS O.K. THOUGH I HAVE NOT MEASURED IT. 12V AT THE COIL AND DISTRIBUTOR (BOTH NEW) AND NO CODES. I STARTED THE TRUCK AND RAN IT FOR A...


Crank sensor ? Power an grounds for the VCM engine computer . CHECKED ALL THE FUSES 3X ,What's this ??? Five volt reference voltage circuit in VCM , Did you check this ? Do you know what the five volt ref. circuit is ?Is there B+ voltage to ICM - ignition control module ?
047 Engine Hard to Start or No Start Scan Data for Ignition
This is the easy way ,viewing scan data .

Jul 30, 2017 | 1998 Chevrolet K1500

1 Answer

I can here the fuel pump running but it wont start 1998 chev k1500 4.3v6


It may be the cam position sensor or the crank position sensor

May 27, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Wont start


you may be having a problem with the connections on the battery or your selenoid on you starter is goin bad

Feb 16, 2009 | 1996 Chevrolet K1500

1 Answer

1998 1500 chev pickup 5.0L cranks but will not start


most comun is fuel selenode or pomp second chek for spak &plugs tird timin components or alarm sistem

Jan 20, 2009 | 1998 Chevrolet K1500

2 Answers

My 98 chev 1500 vortec 5.0l cranks but wont start have spark


bad gas?...can you make it run spraying carb cleaner into intake snorkle?

Dec 08, 2008 | 1998 Chevrolet K1500

1 Answer

Car alarm preventing car from starting


I am having trouble also but I need to know how to disconnect the alarm. I would appreciate it if you could help me out seeing that you have disconnected yours. Thank you

Jul 12, 2008 | 1998 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

243 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...