Question about 2009 Toyota Matrix

Open Question

How do i remove a door panel on a 2009 toyota matrix?

Can u please help me out on removing the passenger side door panel

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: removing door panel in 2000 toyota corolla

remove phillips scew and the door handle. remove padded arm rest on the door by lifting it up, and remove 2 screws. You can use a panel tool to remove the plastic toggle like pins holding the panel border in. Be as gentle as possible they may break due to becoming brittle.

Posted on Apr 06, 2009

Ad
  • 2 Answers

SOURCE: To remove the interior door panel of a 1996 Toyota camry so that

My 96 Camry LE has 9 attachments that are visible. Some have plastic caps covering the screws; others do not. There are screws at the door handle, at the forward portion(with covers) when the door is open and the back edge (small covers). As I recall, there are several friction type fasteners around the perimiter of the panel that can be removed by prying carefully away from the metal portion of the door to free up the trim panel. Once these are loose, the trim around the inside door release handle (the one you pull to open the door) can be pryed in a backward motion. Then the entire panel can be removed by pulling upward and backward at the same time (it easier to do this with the window down). Then it is a matter of disconnecting the wires attached to the various controls for the electric windows and door locks to free up the panel itself. There is probably a plastic skin covering the metal portion of the door. Carefully pull that away to expose the inner workings of the door latch mechanisim. The rest of the procedure should become easy to figure out. I have not removed the exterior door handle itself; but it is a simple mechanism as I recall. Best of luck to you.
Timmy P.

Posted on Mar 04, 2009

  • 316 Answers

SOURCE: remove door panel

Disconnect your negative battery cable. Locate and remove the screws that hold your interior door handles in place (they may be hidden by snap in, or snap on clips). Remove the interior door handles, then disconnect the wire clips to the switches. Your panel is held in place by snap in clips; use a small pry bar to pull them from the door (try to get as close to, or directly under the clips to prevent them from tearing out of the door panel). Once the clips are pulled, pull the panel upward to remove it from the door.
Install in reverse.

Posted on May 25, 2009

  • 1986 Answers

SOURCE: remove passenger side mirror

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Posted on Sep 29, 2009

  • 1986 Answers

SOURCE: Replace 2007 Toyota Rav4 super sport passenger side door mirror

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Posted on Sep 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 kia sportage Passenger power window stopped working from both driver's side and passanger side. Which door panel do i remove? What Next?


Sounds like the motor is bad.remove passenger panel check for voltage at motor ,if no voltage wiring is broken .if there is voltage replace motor

Jul 20, 2014 | 1997 Kia Sportage

1 Answer

I'm trying to find the fuel cut off switch to the fuel pump on an 1984 ford econoline 350 series can you help?


On a 94. The switch on mine is located behind the kick panel on the passenger side. Remove the plastic panel right next to the passenger side door.
On a 95 it's up high, under the dash, on the plastic panel by the passenger door. The panel said "fuel reset", pointing to a hole. Reach in, feel around, press down - didn't even have to remove anything

Feb 21, 2011 | 1984 Ford Econoline

1 Answer

Problem with dual zone heating only one side i check control thermost botton is ok


Sounds like the blend door actuator. It separates the driver and passenger side from getting air on the AZC system. Here are some instructions on replacing it:
The passenger side blend door actuator is used on all models equipped with Automatic Zone Control (AZC). This actuator is located on the front of the HVAC housing to the right of the floor panel transmission tunnel and cannot be removed from the passenger compartment without instrument panel or HVAC housing removal.

NOTE: This procedure is for AZC Systems (Passenger side only).

  1. Disconnect and isolate the battery negative cable.
  2. Remove the glove box door. See: Body and Frame\Interior Moulding / Trim
  3. Remove the lower I/P glove box door surround panel.
  4. Remove the dash assembly. See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
  5. Remove the HVAC assembly. See: Housing Assembly HVAC\Service and Repair
  6. Unplug the wire harness connector from the blend door actuator.
  7. Remove the 2 screws that secure the blend door actuator to the HVAC housing.
  8. Remove the blend door actuator from the HVAC housing.
INSTALLATION - AZC (Passenger side only)


  1. In stall the blend door actuator on the HVAC housing and tighten the two mounting screws to 2.2 Nm (20 in. lbs.).
  2. Plug in the wire harness connector to the blend door actuator.
  3. In stall the HVAC unit into the vehicle. See: Housing Assembly HVAC\Service and Repair
  4. Install the instrument panel assembly into the vehicle. See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
  5. Evacuate the HVAC system.
  6. Recharge the HVAC system.
  7. Connect and the battery negative cable.
Hope it helps! If you need more, just send me an email at familyguy77351 at yah I wil be glad to finish helping you with more detail.

Dec 12, 2010 | 2000 Jeep Grand Cherokee

1 Answer

On a 1998 expedition, where is the pcm and the ecm--5.4 litre


1998 Ford Truck Expedition 4WD 5.4L EFI 8cyl

PCM Ford's Location:
* Ranger - behind instrument panel (cowl), center to both driver and passenger sides.
* Explorer/Mountaineer - behind instrument panel (cowl), (access from engine compartment dash panel) on passenger side to center of vehicle.
* All other F-Series, Expedition/Navigator - lower dash panel on passenger side.
* Excursion - lower dash panel on driver side.

The PCM is behind the glove box and has a big harness connector in the firewall that you access from the engine compartment.

REMOVAL & INSTALLATION

a927c58.jpg

Fig. 1 The calibration number will be needed to order such parts as a replacement PCM, various sensors, and almost any emission control component. Typically this number is attached to a label found on the driver's door or the door pillar


1997-00 F-150, F-250, Expedition and Navigator

00a02b5.jpg

Fig. 2 Loosen the connector retaining bolt and remove the PCM connector

2cda058.jpg

Fig. 3 Remove the passenger side front door scuff plate

1fe310f.jpg

Fig. 4 Remove the passenger side kick panel

234c3f5.jpg

Fig. 5 Remove the PCM bracket clip and remove the PCM
  1. Remove the battery and the battery tray.
  2. Loosen the connector retaining bolt and remove the PCM connector.
  3. Remove the passenger side front door scuff plate.
  4. Remove the passenger side kick panel.
  5. Remove the PCM bracket clip.
  6. Remove the PCM.
To install:
  1. Installation is the reverse of removal.
  2. Tighten the PCM connector retaining bolt to 36-44 inch lbs. (4-5 Nm).

Hope helps.

Jul 13, 2010 | Ford Expedition Cars & Trucks

1 Answer

2002 Cougar passenger side window switch - remove & replace


remove the door panel switch comes off from inside

Jul 23, 2009 | 2002 Mercury Cougar

1 Answer

Removing passenger door panel


There is a screw behind the lock rod. Lift door panel straight up to remove

Jun 13, 2009 | 2003 GMC Yukon XL

2 Answers

Replacing passenger side mirror


no the door pannel does not need to come off but there is a triangle shaped plastic trim pannel above the door pannel that needs to be removed to access the mounting bolts.

May 28, 2009 | 2003 Nissan Xterra

1 Answer

Replace 2007 Toyota Rav4 super sport passenger side door mirror


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Mar 19, 2009 | 2007 Toyota RAV4

2 Answers

Instructions for replacement of side view mirror


the door panel near the mirror must be removed if not the entire door panel inside u will find 3 nuts to remove to get the old mirror off. hope this helps please rate me

Jan 12, 2009 | Pontiac Grand Prix Cars & Trucks

Not finding what you are looking for?
2009 Toyota Matrix Logo

Related Topics:

876 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...