Question about 1996 Nissan Quest

Open Question

Where is pcv valce on 96 nissan quest - 1996 Nissan Quest

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: where is pcv valve on 96 nissan pickup

PCV valve on Nissan 2.4 engine is behind the water pump, under the admission manifold

Posted on Sep 19, 2008

Ad
  • 1 Answer

SOURCE: fuel pump removal

Replace Fuel Pump for 1997 Nissan Quest

(1) If the fuel tank has more than one third full, you need to get the gasoline out. If it has one third or less full, you can leave it in the tank. However be very careful around the working area. Make sure you have read fire precautions in a general repair book. Take the fuel pump fuse out from the fuse box near the battery. Run starter for a few seconds. This will remove the fuel pressure in the gas lines. Disconnect battery at negative terminal. Jack up the rear of the van.

(2) Remove the fuel tank protector.
19add47.jpg

(3) Disconnect fuel pipes at the front end of the fuel tank. Use short pencils and extra rubber hoses to block disconnected pipes and hoses.
59aa089.jpg There are two pipes connected to the gasoline filler at the side of the van. Disconnect only the smaller one. The larger one is flex enough for the tank to be lowered.

(4) Disconnect the electrical from this connector. Jack the rear end of the fuel tank with a car jack and a piece of 2x4. Put the wood between the jack point and the tank. Then unbolt the two bolts showing in the picture.
128654f.jpg
(5) Lower the jack after the bolts are removed. The rear end of the tank should be lowered.
667f695.jpg

de57889.jpg

(6) Disconnect fuel lines on top of the fuel pump. Reconnect each short hose back to different pipes as shown in picture to block the pipes.
585888a.jpg
(7) Loose the six mounting bolts on the fuel pump assembly. The bolts should be loosen a little at a time in multiple turns. Also detach the electrical wire holders. After all bolts are removed, carefully take the assembly out of the tank.
dceea20.jpg

(8) Remove the fuel pump from the assembly as shown in picture. Then unplug the electrical wires. Note that two connectors are in different sizes, so that you will not be able to reconnect to a wrong terminal.
1310aad.jpg
(9) Put the new pump and new filter in. Reconnect the electrical wires. If necessary use a pair of pliers to make the connectors tighter. Make sure they are not loose. Reconnect gas inlet to the pressure regulator.
08db176.jpg
(10) Use a new O ring, put back the assembly to the fuel tank. Make sure the float of the fuel level senser is free, and the assembly is at the right orientation (as shown in picture). Screw back the 6 bolts after making sure the O ring is in right place. The bolts should be tightened in turns. Do not over tighten them. Then reconnect the fuel lines and make sure every fastener is tight. Put the electrical wire into holders.
90c2053.jpg
(11) Jack up the tank and put the two mounting bolt in. (see picture in step 4). Make sure they are tightened with specific torque. Reconnect the electrical connector.

(12) Reconnect two fuel lines at the front side of the tank. Refer to the picture in step 2. Reconnect the hose to the gasoline filler. Before you have a try start, double check if all fuel lines are securely connected and tightened.

(13) Start the engine. You need to crank more than a normal start because the lines were empty. The pressure is built up in some time.

(14) If engine starts ok, turn it off. Then check under the van if there is any leakage. If everything is fine put back the tank protector. (picture in step 2).

Posted on May 05, 2009

  • 561 Answers

SOURCE: where is the oil filter for my 96 nissan quest

most likely it is on the side of the engine between the engine and the bulkhead
the side away from the front of the car.

you will have to get at it from underneath and remove and engine protection cover that maybe in the way.

I hope this was helpful.

Posted on Dec 12, 2010

  • 6 Answers

SOURCE: how so i change the water pump on a nissan quest

go to utube there will be some 1 that has it there.

Posted on Mar 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace pcv valve on 2001 nissan quest


It will be located in one of the valve covers but nissan has used a fixed orifice crankcase vent sysrem which would just be a vacuum line fittings with a small opening inside the line from that valve or orifice would connect to manifold vacuum (intake maifold after the throttle plates)

Jul 03, 2015 | 2001 Nissan Quest

1 Answer

2004 nissan quest no spark


Pcv hose on upper rear of intake manifold rotted through and causing a vacume leak. spray carb cleaner at mid rear of manifold and idle will drop and stall. pretty hard to replace but thats nasty nissan.

Aug 21, 2010 | 2004 Nissan Quest

1 Answer

Why do I get white smoke only when I start the engine on my 2007 nissan quest? Could it be the PCV valve?


It could be the pcv vavle or or you could have some bad piston rings that are leaking by

Jul 29, 2010 | 2007 Nissan Quest 3.5 Minivan

1 Answer

My 96 nissan quest is very hard to steer and it jerks when trying to turn. It also makes a squealing noise.


Check the power steering fluid. Sounds like it is empty. If not, check the belt and the tension on the belt.

Feb 28, 2010 | 1996 Nissan Quest

1 Answer

1996 nissan quest fuse box diagram?


I have a 96 Villager wirng diagram. same as quest. $10 including shipping. Let me know.

go here and our team will help you

http://groups.yahoo.com/group/villagerquest/

Jan 31, 2010 | 1996 Nissan Quest

1 Answer

Ac pump oil


3 to 6 ozs of oil for pag oil or oil that will work for r134a.

Jun 17, 2009 | 1993 Nissan Quest

1 Answer

My 96 nissan quest wont crank.


might wanna try checking the starter, sounds like the solenoid is bad

May 24, 2009 | 1996 Nissan Quest

Not finding what you are looking for?
1996 Nissan Quest Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...