Question about 2006 Dodge Ram 2500

Open Question

Check engine light after battery change

I just changed both batteries on my 2006 dodge diesel and now the check engine light stays on all the time. How do I reset the light?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 83 Answers

SOURCE: 2006 Dodge Ram 2500 diesel truck----need inside fuse box diagram

If you are looking for the fuse box diagrams or any other diagrams for your Ram, check promanuals.net for a factory service manual for around 20 bucks or so. It's an invaluable tool for my Ram 2500.

Posted on Sep 26, 2009

Ad
nick_helpap
  • 334 Answers

SOURCE: How do you change the battery on a 2006 dodge stratus?

is it unde rthe tire ? front my my serbing or can u get to it under hood ? if its tire one u hav eto remove fornt left tire take out platsi stuff then thers batter behind wall k thx nick

Posted on Oct 06, 2008

  • 3 Answers

SOURCE: 2006 dodge magnum check engine

Get in the car, close the door. Perform the following steps fairly quickly (less than 3 seconds) :

Turn key to ON
then back to ACC
then to ON
then back to ACC
then to ON

If there are any stored codes, they will appear immediately, in place of the odometer. For instance an "INTAKE AIR TEMPERATURE SENSOR CIRCUIT HIGH" error will set a code of P0113.


You may also try and pull Fuse 11, and wait 10-15 seconds to reset the cars internal computers.
More information can be foudn here: http://www.custommagnums.com/forums/misc-mods/1361-how-check-obd-2-codes.html

Posted on Jan 15, 2009

BCally1
  • 133 Answers

SOURCE: changing fuel filter on 2006 dodge ram 2500 diesel

fuel filter housing on driver side of motor. need the correct size of socket to remove the lid. unscrew lid and pull straight up to remove filter. remove old filter from lid and install new filter and seal. drain old fuel/water from housing. then reinstall filter into housing. tigthten lid then make sure the petcock is closed from draining it earlier. bump the starter a couple times to fill the filter housing then start engine. clean any spilled fuel and your done

Posted on Jan 22, 2009

bschilz
  • 2049 Answers

SOURCE: 2006 Dodge diesel belt routing diagram

Here's a link to the diagram you need...

http://www.gates.com/common/part_locator/view_diagram.cfm?id=S8023

Posted on Sep 23, 2009

Testimonial: "Awesome! thank you so much for the quick response!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just changed my oil and my fuel filter on my Dodge Ram 3500 Diesel. Now my check engine light is on.


computer in your Dodge truck generates and stores error codes related to critical vehicle component systems. When your Dodge truck generates one of these codes, a Check Engine Light will illuminate on the dash. This light can indicate a variety of problems. Ironically, only several codes pertain to the actual engine in your truck. Many of the codes can indicate a problem with the transmission, emissions control system and even the fuel system. To erase the code and get the light to go off, you will need to reset the computer. This will involve cutting the power to the computer. Instructions

1 Open the hood and loosen the retaining nut connected to the battery cable clamp that is attached to the negative battery terminal. 2 Slide the negative battery cable clamp off the battery terminal. 3 wait five seconds then slide the battery cable clamp back over the negative battery terminal. The Dodge's computer will now be reset. 4 Tighten the retaining nut on the cable clamp to secure the clamp to the battery. On some Dodge trucks, you will need to drive an additional 500 miles from the time you cut power to the computer for the Dodge's computer to fully reset.

Sep 29, 2011 | 2005 Dodge Ram 3500

1 Answer

Changed out battery now we need to reset computer


On most vehicles if you leave the battery disconnected for 3 hrs the computer will reset. This is enough time for the power back up in the computer to go dead and reset itself. I know it sounds stupid, but it works. Should make check engine light turn off

Oct 30, 2010 | 2006 Dodge Caravan

1 Answer

Glow plu circuit #2 shorted on dodge sprinter van. check engine light on. what do i change


i would change all glow plugs and the relay. while doing so make sure the battery is disconnected, also once i had a sprinter with multiple codes and intermittently would run very rough and sometimes not drivable.changed the engine wiring harness and the problem was solved.

Aug 27, 2010 | 2006 Dodge Sprinter

2 Answers

I have 2006 fiat doblo van diesel which wont start after along time standing how can i reset it


check all connectors, fuse and check smo hose and pipe for clogging(air&fuel lines)

Jun 19, 2010 | 2006 Fiat X1/9

1 Answer

2006 dodge magnum check engine light stays on had checked


Hello
Try disconnecting the battery then connecting the scan tool then reconnect the battery
RD

Jan 12, 2009 | 2006 Dodge Magnum

1 Answer

My engine would not start it a 2006 kia sorento diesel ,manual


U may find that the negative battery cable has worn and it needs replacing. Check from battery down to the car cassie. That happened to me on my Nissan.

Matt

Jan 02, 2009 | 2006 Kia Sorento

1 Answer

Will not start


make sure both batteries are charged, clean battery terminals, make sure the wire coming from the rear of your alternator is snug on the positive battery post. I take it that it's a diesel-(you said batteries} One last thing to try if it's turning over good but not firing; CHECK THAT 10 AMP FUSE THAT SAYS: ENGINE FUSE. hope this helps

Dec 26, 2008 | 2006 Dodge Ram 3500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

716 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...