Question about 2004 Ford Expedition

Open Question

How to remove door panel and trim on to replace window motor 2004 ford expedtion xlt

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: I need to replace the window regulator

Go to this website

http://www.fordf150.net/articles/idx.php/0/019/article/How-To-Repair-the-Power-Window-Regulator--Motor.html

Posted on Oct 24, 2008

Ad
mohammed387
  • 1952 Answers

SOURCE: I have a 1993 Ford

remove the door panel and check to make sure the linkage to the lock assembly is still attached. I can't give an estimate because I don't know what is wrong at this point

are the locks manual or electric?i have seen most electric locks freeze up because of rust/.corrosion.the rubber accordian seal fails and moisture does it's job.there is no lubrication on the mechanism.it's basically a push pull magnet tube with a spiral grooved actuator rod.this is to assure no accidental vibration/jar induced movement.also means very difficult to budge when corroded.i have gotten a few to move by grabbing lock post with pliers and pulling hard.good luck!



Rear Door Window Regulator and Motor
Removal and Installation
Remove the rear door trim panel. For additional information, refer to INTERIOR TRIM AND ORNAMENTATION .
Remove the door mounted speaker.
Remove the watershield.
NOTE:The glass must be lowered for this step.

NOTE:Some vehicles may use rivets to attach the glass to the regulator.

Remove the bolt that attaches the glass to the regulator.
Raise and support the rear door window glass to the full up position.

NOTE:Do not detach the door handle from the latch cable during this step.

Remove the rear inside door handle.
Remove the screw.
Disengage the inside door handle from the door.
If equipped, disconnect the power door lock rod from the back of the inside door handle.

Gain access to the power window motor electrical connector located in the front of the door.
Fig. 90: Identifying Power Window Motor Electrical Connector
Courtesy of FORD MOTOR CO.
Disconnect the power window motor electrical connector.
Press down on the connector tab.
Pull the connector upward and remove through the speaker opening in the door.
Disconnect the rear door window regulator and motor assembly from the door.
Remove the nuts.
Remove the screws.
Fig. 92: Disconnecting Rear Door Window Regulator And Motor Assembly From Door
Courtesy of FORD MOTOR CO.
266999_door_2.jpg
Remove the window regulator and motor assembly from the door.
Fig. 93: Removing Window Regulator And Motor Assembly From Door
Courtesy of FORD MOTOR CO.
266999_door_3.jpg

To install, reverse the removal procedure.

Posted on Jul 01, 2009

emissionwiz
  • 76051 Answers

SOURCE: How do I remove the power window motor on a 1989

the motor is located at the front of the door at bottom, on the sheet metal in front of the motor u will see three dimples/indentations in the door skin sheet metal covering the motor, drill them out with a 1/2" drill bit, use a 1/4" drive 8mm or 5/16" deep socket and a short extension and remove the three bolts that hold the motor into the regulator, then gently push back on ,motor, remove harness to motor and remove motor through access hole.

Posted on Aug 10, 2009

  • 3 Answers

SOURCE: Remove door panel on a Ford Van

For a 1999 Ford Econoline 150 (assume the same or very similar), remove triangular plastic cover over mirror assembly by prying straight out, remove plastic door handle cover by prying up from the front side, remove electronic door switches by prying up from back side, remove round plastic cover at bottom rear of door panel. Four screws are now revealed, remove them. Lift door panel straight up, clips are hooks (not snap in). Work door switch assembly out of door panel. Set door panel aside. Reassemble in reverse order.

Posted on Nov 21, 2009

  • 1 Answer

SOURCE: how to remove interior door panel on 2004 ford

First pop off the door open handle back plate with a screwdriver. It just snaps on. Do the same with the switch cluster plate below which also snaps in place and remove the switch harness connectors. Next pop off the small narrow cover plate under the armrest pull handle to expose 2 Torx screws. Remove these screws. Next locate a Phillips screw in a retaining cup which is located on the end of the interior door panel just above the latching mechanism and remove that. Locate two 3/8" hex head screws at the bottom of the door panel and remove those. Grab the door panel by the armrest handle and pull up to unhook it from the door. If its the driverside door, you will also have to diconnect the mirror adjustment switch connector to free the door panel.

Posted on Mar 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the power window motor for ford F150,1999 xlt 1 1/2 cabin. Thank you.


1. Raise glass to full up position. (Often, this step is not possible due to broken window regulator or faulty motor. you just have to figure a way around it)

2. Remove door trim panel

3. Peel back water shield. Be careful not to tear it, so it can be put back into place.

4. find the 2 "dimples" in the door panel just opposite the window motor assembly. Using a 3/4" hole saw with a 1/4" pilot, drill the door panel at the dimples to expose the window motor mounting screws. The third motor mounting screw should be accessible without drilling.

5. remove the electrical connector from the motor

6. remove the mounting screws

7. Remove window motor.

8. To install, reverse removal procedure (skipping step 4)

Feb 19, 2011 | Ford F-150 Cars & Trucks

2 Answers

Need to pull the panel off driver side door of 2004 ford f150


SECTION 501-01: Body System — Interior 2004 F-150 Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 02/17/2004 Front Door Trim Panel adobe.gif Printable View (229 KB) Removal and Installation
NOTE: LH side is shown. RH side is similar.
  1. Remove the front door speaker. Refer to Section 415-00.
  1. If equipped, remove the window regulator handle.
    1. Separate the handle cover from the handle.
    1. Remove the screw.
    1. Remove the window regulator handle.
    1. Remove the spacer.
    r12386a.gif
  1. Remove the parts in the order indicated in the following table.

    a0005479.gif
    Item Part Number Description 1 224A60 Cover plate 2 N602704-S301 Screws (2 req'd) 3 14B132A (RH) / 14B133B (LH) Window control switch 4 14630 (RH) / 14631 (LH) Window control switch electrical connectors 5 W505424-S301 Bolt 6 W701930-S424 Bolts (2 req'd) 7 19A034 Water shield 8 W709132-S300 (High series trim) / W709133-S300 (Low series trim) Speaker standoff (2 req'd) 9 219A65 (LH)/ 219A64 (RH) Front door handle
    Removal Note 10 23942 (RH) / 23943 (LH) Front door trim panel
    Removal Note
  1. To install, reverse the removal procedure.
Item 9: Front Door Handle Removal Note
  1. Guide the door handle through the opening in the trim panel.
Item 10: Front Door Trim Panel Removal Note
ani_caut.gif CAUTION: Do not pull directly outward on the front door trim panel, as damage may occur.
  1. Lift upward and remove the front door trim panel.

2010&c18=modelyear&c20=n717901&c35=wsm%2cfront%20door%20trim%20panel%2cs42%2c501-01%2cremoval%20and%20installation&pid=wsm%2ctitle%20page%202004%20f-150%2cs42&pidt=1&oid=functiononclick%28%29%7bdosearch%28%29%3b%7d&oidt=2&ot=img&oi=27&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=491&ct=lan&hp=n&[aqe]

Apr 03, 2010 | 2004 Ford F150

1 Answer

How do you replace the regulator for the power window on the 2002 ford explorer


Regulator - Power Windows - Front Door
  1. Remove the front door trim panel as follows:
    1. Remove the front door handle bezel.
    2. Remove the front door window/lock control switch bezel.
    3. Disconnect the window/lock control switch electrical connectors.
    4. Remove the 3 front door trim panel screws.
      CAUTION To avoid damaging the trim panel, do not pull directly outward to carry out this step.
    5. Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
    6. Remove the exterior mirror control switch from the front door trim panel.
  2. Remove the front door speaker.
  3. Remove the interior molding.
  4. Disconnect the door lock actuating rod at the door handle assembly:
    1. Release the door lock actuating rod clip.
    2. Position the door lock actuating rod aside.
  5. Remove the front door weather shield.
    CAUTION Make sure the holes in the glass bracket do not become enlarged during the rivet removal process. If the holes become enlarged, the new rivets may become loose, resulting in clicking noise concern.
    NOTE Some vehicles may use rivets to attach the window glass to the window regulator assembly. Use a 4.5 mm (0.1772 in) drill bit to drill out the glass-to-regulator rivets.
  6. Remove the 2 front door window glass-to-regulator bolts or rivets.
  7. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets.
  8. Secure the front door glass in the full up position with tape.
  9. Disconnect the window regulator motor electrical connector.
  10. Remove the 4 window regulator assembly nuts.
  11. Remove the window regulator assembly.

    0b00886.jpg

    Fig. Exploded view of the front door and power window components-2005 Explorer and Mountaineer

To install:
  1. Position the window regulator assembly.
  2. Install the 4 window regulator assembly nuts. Tighten to 89 inch lbs. (10 Nm).
  3. Connect the window regulator motor electrical connector.
  4. Remove the tape securing the front door glass in the full up position.
  5. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets. Install the bolt and tighten the bolts to 62 inch lbs. (7 Nm), or install new rivets.
  6. Install the front door weather shield.
  7. Connect the door lock actuating rod at the door handle assembly:
    1. Position the door lock actuating rod into proper location.
    2. Attach the door lock actuating rod clip.
  8. Install the interior molding.
  9. Install the front door speaker.
  10. Install the front door trim panel as follows:
    1. Install the exterior mirror control switch from the front door trim panel.
    2. Position the door trim panel onto the armrest to engage the panel clips.
    3. Install the 3 front door trim panel screws.
    4. Connect the window/lock control switch electrical connectors.
    5. Install the front door window/lock control switch bezel.
    6. Install the front door handle bezel.

  1. Raise the front door window glass to the full up position.
  2. Remove the interior door handle.
  3. Support the front door window glass.
  4. Disconnect the front door window regulator motor electrical connector.
  5. Remove the equalizer bracket nuts.

    4945f24.jpg
    Fig. Remove the equalizer bracket nuts-2005 Explorer Sport-Trac
  6. Remove the front door window regulator by removing the rivets and nuts.
  7. Remove the front door window regulator motor retaining bolts and then remove the motor.

    52a6816.jpg

    Fig. Remove the front door window regulator motor retaining bolts and then remove the motor-2005 Explorer Sport-Trac
To install:
  1. Installation is the reverse of the removal procedure.
  2. Tighten the regulator motor mounting bolts to 8 ft. lbs. (11 Nm).

Hope this help (remember rated and comment this).

Mar 24, 2010 | 2002 Ford Explorer

2 Answers

I need help with replacing the driver side window in a 2003 ford f-150,four door super crew cab truck.


Removal & Installation
Motor - Front Door
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch
  3. Remove the front door trim panel and watershield.
  4. Tape the window in the full UP position.
  5. Disconnect the window motor electrical connector.
    NOTE Support the window motor while removing the window motor retaining screws.
  6. Remove the window motor bolts and remove the motor.
  7. To install, reverse the removal procedure.
Rear Door
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch.
  3. Remove the rear door trim panel and the rear door trim watershield.
  4. Remove the door speakers.
  5. Tape the window glass in the full UP position.
  6. Disconnect the window regulator electric drive.
  7. Position the connector for the window regulator electric drive inside of the door.
  8. Remove the bolts.
  9. Separate the window regulator electric drive from the rear door window regulator.
  10. Remove the window regulator electric drive from the door.
  11. To install, reverse the removal procedure.

Motor & Regulator

3d4a07e.jpg

Fig. Front Door Trim Panel

7932e42.jpg


Fig. Rear Door Trim Panel-Crew Cab


Regulator - Power Windows

506866e.jpg

Fig. Window regulator arm nuts


db15984.jpg

Fig. Window regulator bolts

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the window control switch.
  3. Remove the door trim panel.
  4. Remove the door speaker.
  5. Remove the door watershield.
    NOTE Do not remove the window glass from the door.
  6. Remove the window glass from the window regulator.
  7. Tape the window glass in the full UP position.
  8. Disconnect the window motor electrical connector (power windows only).
  9. Loosen the window regulator arm nuts and pull the arm from the mounting position.
  10. Loosen the bolts and remove the window regulator.
  11. To install, reverse the removal procedure.

Hope helped with this. Good luck.

Nov 16, 2009 | 2003 Ford F150 Regular Cab

2 Answers

Removing/installing 2000 dodge grand caravan window glass


after u remove the bolts that hold it to the window regulator tip the window towards the front of the door and the top rear corner of the window should pop out and then u just lift hte window out,hope this helps

Sep 05, 2009 | 2004 Dodge Caravan

1 Answer

Remove and replace passenger door mirror on 2009 ford explorer XLT, main part , I don't know how to remove the interior door panel. Pictures might help,


  1. Remove the front door trim panel handle bezel cover.
  1. Remove the front door trim panel handle bezel screws.
  1. Remove the front door trim panel lower screws.
NOTICE: To avoid damaging the front door trim panel, do not pull the bottom of the panel outward.
  1. Remove the front door trim panel by lifting upward on the armrest to disengage the panel clips.
  1. Disconnect the electrical connectors.
  1. Disconnect the lock rod cable from the front door trim panel.
  1. Disconnect the door handle conduit and cable from the front door trim panel.
  1. To install, reverse the removal procedure.

be patient during these procedures to not damage the trim panel...they cost $150>275 ec........GL hope this helps

Jul 06, 2009 | 2009 Ford Explorer

1 Answer

2003 ford taurus drivers window will not go up.


you either need a motor or motor and window regulator assembly.
SECTION 501-05: Interior Trim and Ornamentation 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Trim Panel Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the front door trim panel screws.
  1. NOTE: To release the door trim panel two part pin-type retainers, first pull outward on the bottom of the door trim panel.
    Remove the front door trim panel.
    • Disconnect the electrical connectors.
c64985a.gif --------------------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Front Door Window Regulator And Motor
Special Tool(s) s2h~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
501-D011 (D80L-23200-A) or equivalent
Removal and Installation
  1. Remove the front door window glass. For additional information, refer to Front Door Window Glass in this section.
  1. Disconnect the front door window regulator motor electrical connector.
  1. Remove the window regulator rivets.
-----------------------------
SECTION 501-11: Glass, Frames and Mechanisms 2002 Taurus/Sable Workshop Manual
REMOVAL AND INSTALLATION Door Window Regulator Motor Removal and Installation
  1. Close the window.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the door trim panel. For additional information, refer to Section 501-05 .
  1. If equipped, remove the radio speaker.
  1. Position the watershield aside.
  1. Disconnect the door window regulator motor electrical connector.
  1. Remove the bolts and the door window regulator motor.
---------------------------------------------------

May 04, 2009 | Ford V6 Pony Cars & Trucks

1 Answer

Removal of rear door panel to access power window motor


SECTION 501-05: Interior Trim and Ornamentation 2000 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Rear Door Trim Panel Removal and Installation
  1. Remove the rear door trim panel screws.
  1. NOTE: The rear door trim panel has eight two-part pin-type retainers. The male part of the retainer will remain with the trim panel and the female part will remain with the door.
    NOTE: To release the door trim panel pin-type retainers, first pull outward on the bottom of the door trim panel.
    Remove the rear door trim panel.
    • Disconnect the window regulator control switch electrical connector.
  1. To install, reverse the removal procedure.

Apr 07, 2009 | 2000 Ford Taurus

1 Answer

2004 Mercury Monterey left frnt window sector gear R&R proceedure


are you a techie? You need a heavy duty riveter to do this repair. May have to rent or borrow from auto store.

here's the procedure



Front Door Trim Panel s4w~us~en~file=adobe.gif~gen~ref.gif Printable View (251 KB) NOTE: LH side is shown. RH side is similar.
  1. Remove the parts in the order indicated in the following illustration and table.

    df2877a.gif

  2. Item Part Number Description 1 23942/23943 Mirror access panel 2 1722897 Cup assembly 3 W56904-S424 Window regulator control switch panel screws 4 14A665 Window regulator control switch panel
    Removal Note 5 W701930-S424 Front door trim panel screw 6 W701930-S424 Front door trim panel screw 7 N602703-S61 Front door trim panel screw 8 1723943 Front door trim panel 9 W705590-S300 Nut insert(s)
  1. To install, reverse the removal procedure.
Item 4: Window Regulator Control Switch Panel Removal Note
  1. If equipped, disconnect the electrical connector(s).
-----------------------------------------------------------------------------------
Door Window Glass — Front s4w~us~en~file=adobe.gif~gen~ref.gif Printable View (328 KB)
Special Tool(s) s4w~us~en~file=st1132a.gif~gen~ref.gif Heavy Duty Riveter
501-D011 (D80L-23200-A)
  1. Remove the front door trim panel. For additional information, refer to Section 501-01 .
  1. Position the watershield aside.
  1. Remove the parts in the order indicated in the following illustration and table.

    To remove individual parts, only carry out the listed steps: Part Steps Front door window glass 1, 3 Front door window regulator 1-5 Front door glass run 1, 3, 6-8
    4be8135.gif
Item Part Number Description 1 W706495-5100 Rivet (2 required)
Removal Note
Installation Note 2 N8621986 Nut (3 required) 3 21410 Front door window glass 4 W706495-5100 Rivet (4 required)
Removal Note
Installation Note 5 23200 Front door window regulator
Removal Note 6 N800507-S Bolt (2 required) 7 21596 Front door glass run 8 — Front door glass run (Part of 21596)
  1. To install, reverse the removal procedure.
Item 1: Rivet Removal Note
  1. Connect the window control switch.
  1. Connect the battery.
  1. Position the door window glass halfway down to gain access to the door window glass rivets.
    • Remove the rivets.
9391398.gif Item 4: Rivet Removal Removal Note
  1. Remove the rivets.
Item 5: Front Door Window Regulator Removal Note
  1. Disconnect the electrical connector.
  1. s4w~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Prior to power window motor removal, make sure the regulator arms are in a fixed position to prevent counterbalance spring unwind. Failure to place the regulator arms in a fixed position can cause the spring to suddenly release resulting in personal injury.
    NOTE: The counterbalance spring assists the window in the upward direction.
    Remove the bolts and the window regulator motor.
Item 4: Rivet Installation Note
  1. Using the special tool, install the rivets.
b4c4793.gif

Feb 21, 2009 | 2004 Ford Freestar

1 Answer

I have a 1998 Ford Explorer.


  1. Remove the rear pivot arm; refer to Pivot Arm—Rear . 7981ec7.gif
  2. Remove rear pivot arm.
    1. Lift the pivot arm nut cover.
    1. Remove the nut.
    1. Remove the pivot arm.
  1. Remove the liftgate door trim panel; refer to Section 501-05 . Remove the (A) liftgate handle to liftgate screws and the (B) liftgate handle. Remove the liftgate trim panel screw access plug. Remove the screw.
  2. Remove the liftgate door trim panel.
    1. Use Windshield and Molding/Trim Removal Kit to remove the liftgate door trim panel from the liftgate window opening.
    1. Push the liftgate door trim panel toward the top of the liftgate and remove the liftgate trim panel. 9e75e00.gif
  1. Position the watershield aside to gain access to the rear wiper motor.
  1. Remove rear wiper motor.
    • Disconnect electrical connector.
    • Remove three retaining bolts.
    • Remove rear wiper motor.
good luck.

Jan 10, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
2004 Ford Expedition Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...