Question about 2006 Chrysler Town & Country

1 Answer

How do you get a pulley off to replace water pump?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

If there is no bolts on the pulley then it is probably pressed on. If so then you will have to get a pulley puller and pull it off

Posted on Feb 12, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

92 buck century water pump pulley broke. how to replace


If the pulley actually came off the water pump then it was more than likely an integral part of the pump itself. Separate pulleys are usually attached with four bolts, and unless they were incorrectly installed they do not fall or break off. In this case the pulley was probably permanently attached to the pump and therefore the water pump itself will need to be replaced.

Feb 26, 2015 | Cars & Trucks

1 Answer

I would like instructions on changing a water pump in 2005 Chevy uplander V6 3900


This is probably the easiest water pump of all vehicles to change.


c0ebf96b-78f3-4862-ba77-ee445584a574.gif

Water Pump Replacement

Removal Procedure



  1. Drain the cooling system.
  2. Loosen the water pump pulley bolts.
  3. Remove the drive belt.
  4. Remove the water pump pulley bolts and pulley.


  1. Remove the water pump bolts, pump, and gasket.
  2. Clean the water pump mating surfaces.
Installation Procedure



  1. Install the water pump gasket and pump (1).
Notice: Refer to Fastener Notice in Service Precautions.

  1. Install the water pump bolts.
    • Tighten the bolts to 10 Nm (89 inch lbs.) .


  1. Install the water pump pulley and bolt until snug.
  2. Install the drive belt
  3. Install the water pump pulley bolts.
    • Tighten the bolts to 25 Nm (18 ft. lbs.) .
  1. Fill the cooling system
  2. Inspect for leaks.

Aug 18, 2013 | Cars & Trucks

1 Answer

Water pump


Which engine?

  1. Drain the radiator

91192665


  1. Loosen the water pump pulley bolts.
  2. Remove the serpentine belt.

91192666
  1. Remove the water pump pulley bolts and pulley.
  2. Remove the water pump bolts, pump and gasket.
  3. Clean the water pump mating surfaces.
Installation Procedure
  1. Install the water pump gasket and pump.
91192667


  1. Install the water pump bolts. Tighten the water pump bolts to 89 inch lbs.

91192668
  • Install the water pump pulley and bolt until snug.
  • Install the serpentine belt.
  • Tighten the water pump pulley bolts. Tighten the water pump pulley bolts to 18 ft. lbs.
  • Fill the cooling system and purge of air.
  • Inspect for leaks.
  • Sep 27, 2012 | 2001 Oldsmobile Alero

    1 Answer

    How long does it take to replace a water pump on Pontiac Aztec?


    It takes near to 1.5 hours to replace the water pump on Pontiac Aztec. The procedure to replace the water pump is as follows:--- Water Pump Replacement ---------
    Removal Procedure :
    techmecho.gif
    1. Drain the cooling system until the coolant is below the level of the water pump.
    2. Remove the drive belt guard.
    3. Loosen the water pump pulley bolts.
    4. Remove the drive belt.
    techmecho_0.gif
    1. Remove the water pump pulley bolts.
    2. Remove the water pump pulley.
    techmecho_1.gif
    1. Remove the water pump bolts.
    2. Remove the water pump.
    3. Remove the water pump gasket.
    4. Clean the water pump mating surfaces
    Installation Procedure
    1. Install the water pump gasket.
    2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
    3. Install the water pump bolts.
      • Tighten the bolts to 10 Nm (89 inch lbs.) .
    techmecho_2.gif
    1. Install the water pump pulley. Loosely install the mounting bolts.
    2. Install the drive belt.
    3. Install the water pump pulley bolts.
      • Tighten the bolts to 25 Nm (18 inch lbs.) .
    techmecho_3.gif
    1. Install the drive belt guard.
    2. Fill the cooling system.
    3. Inspect the cooling system for leaks.
    4. That's it.

    Nov 18, 2010 | 2001 Pontiac Aztek

    1 Answer

    Remove and replace the water pump buick rendezvou 2003 cost and do it yourself instructions . can i do it myself concerned with loosening the serpentine belt and needing special tools?


    1. Drain the cooling system until the coolant is below the level of the water pump. 2. Remove the drive belt guard. 3. Loosen the water pump pulley bolts. 4. Remove the drive belt. 5. Remove the water pump pulley bolts. 6. Remove the water pump pulley. 7. Remove the water pump bolts. 8. Remove the water pump. 9. Remove the water pump gasket. 10. Clean the water pump mating surfaces. Installation Procedure 1. Install the water pump gasket. 2. Install the water pump Notice: Refer to Fastener Notice in Service Precautions. 3. Install the water pump bolts. Tighten the bolts to 10 Nm (89 inch lbs.). 4. Install the water pump pulley. 5. Install the water pump pulley bolts. 6. Install the drive belt. Tighten the water pump pulley bolts to 25 Nm (18 inch lbs.). 7. Install the drive belt guard. 8. Fill the cooling system
    Visit my Blog here

    Jul 21, 2010 | 2002 Buick Rendezvous

    1 Answer

    Water pump replacement-putting it back in and setting the timing.


    1. Step 1 Park your car overnight and put a large white piece of paper underneith your car. In the morning check the paper. If the paper is wet with liquid, you could have a water pump leak.
    2. Step 2 If the paper has green (in most cases) fluid on it, there is a good chance your vehicle is leaking coolant (sometimes refered to as "water"). In many cases, when you are leaking coolant it could be coming from the water pump.
    3. Step 3 Turn the engine off and open the hood.
    4. Step 4 Locate the water pump pulley. The pulley is the round part that the belt is attached to. To find it, look for the belts. You will see more than one pulley. Your car will have an alternator with a pulley and perhaps an air conditionermag-glass_10x10.gif, power steering and smog pump pulleys. If you are unsure, ask your mechanic to point out the water pump pulley.
    5. Step 5 Grab opposite ends of the round pulley and check for "play" (looseness): Try to rock it back and forth. There should be no give. If there is, the bearings are going and it's time to replace the water pump. By the time you can feel play in the water pump pulley, you may also be able to hear the bad bearing when the engine is running - there may be a low-pitched grinding noise coming from the water pump pulley.
    6. Step 6 Visually check the water pump (it's located behind the pulley) for signs of a coolant leak. If the water pump gasket is leaking, it must be replaced. This is a good time to get a new water pump, too, unless it was just recently replaced

    Jun 03, 2010 | 1996 Pontiac Sunfire

    2 Answers

    Water pump pulley


    The water pump needs replaced.

    May 08, 2010 | 2006 Pontiac Grand Prix

    2 Answers

    How do you replace the water pump?


    PLEASE DON'T FORGET TO RATE!!!!

    3904240.gif
    After removing the cooling fan assembly, remove the water pump pulley-4.3L engine

    ae70d4b.gif
    Location the water pump pulley bolts-2.2L engine

    e1a6562.gif
    If the pulley turns when you try to loosen the bolts, attach sockets and ratchets to two of the bolts, insert a pry bar to hold the pulley in place and loosen the bolts-2.2L engine

    be1972d.gif
    Once all the bolts are unfastened, remove the water pump pulley-2.2L engine

    46ec457.gif
    Disconnect all hoses attached to the water pump assembly-4.3L engine

    18c0897.gif
    Unfasten and remove the water pump retaining bolts-4.3L engine

    e8016bd.gif
    The water pump is retained by four bolts-2.2L engine

    30f4c89.gif
    Remove the water pump from the vehicle-4.3L engine

    9b0c7fe.gif
    Removing the water pump from the engine block-2.2L engine

    dea099d.gif
    Use a scraper to clean the old gasket material from the water pump ...

    2eaa00c.gif
    ... and the water pump-to-engine mating surface

    Nov 11, 2009 | 1998 Chevrolet S-10 Pickup

    1 Answer

    How do you replace a water pump in an aztec?


    Notes Water Pump Replacement

    Removal Procedure
    3e77de9.gif

    1. Drain the cooling system until the coolant is below the level of the water pump.
    2. Remove the drive belt guard.
    3. Loosen the water pump pulley bolts.
    4. Remove the drive belt.


    c7273fb.gif
    1. Remove the water pump pulley bolts.
    2. Remove the water pump pulley.
    c102468.gif
    1. Remove the water pump bolts.
    2. Remove the water pump.
    3. Remove the water pump gasket.
    4. Clean the water pump mating surfaces
    Installation Procedure
    1. Install the water pump gasket.
    2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
    3. Install the water pump bolts.
      • Tighten the bolts to 10 Nm (89 inch lbs.) .
    f16e1fd.gif
    1. Install the water pump pulley. Loosely install the mounting bolts.
    2. Install the drive belt.
    3. Install the water pump pulley bolts.
      • Tighten the bolts to 25 Nm (18 inch lbs.) .
    • 258f600.gif
    1. Install the drive belt guard.
    2. Fill the cooling system.
    3. Inspect the cooling system for leaks

    Jun 17, 2009 | 2001 Pontiac Aztek

    1 Answer

    Water pump replace


    Water Pump Replacement (3.8L)

    Removal Procedure
    1. Drain the cooling system.
    2. Loosen the water pump pulley bolts.
    3. Remove the drive belt.
      1. Remove the water pump pulley bolts.
      2. Remove the water pump pulley.
      3. Remove the power steering pump and reposition.
      4. Remove the water pump bolts.
        1. Remove the water pump.
        2. Remove the water pump gasket.
        3. Clean and inspect the water pump mating surfaces.
        Installation Procedure
        1. Install the water pump gasket.
        2. Install the water pump.
          1. Notice: Refer to Fastener Notice in Service Precautions. Install the water pump bolts.
            • Tighten the long water pump bolts to 34 Nm (25 ft. lbs.) .
            • Tighten the short water pump bolts to 22 Nm (16 ft. lbs.) .
              1. Install the water pump pulley.
              2. Install the water pump pulley bolts.
                • Tighten the bolts to 13 Nm (115 inch lbs.) .
              1. Install the power steering pump.
              2. Install the drive belt.
              3. Fill the cooling system.
      5. The Whole Thing I Know You Didnt Want to hear that about The P/S Pump Thats why I Did More Reserch you seemed to Know what You are Doin They get the Best of us though Hope this Helps & RATE ME PLEASE

    Feb 03, 2009 | 2005 Chevrolet Impala

    Not finding what you are looking for?
    2006 Chrysler Town & Country Logo

    34 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8152 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...