Question about 1991 Chevrolet Corvette

Open Question

91 Chevy Corvette crankshaft sensor location - 1991 Chevrolet Corvette

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
techbuster
  • 5081 Answers

SOURCE: location of crankshaft sensor on a 98 chevy s10

It is located on the passenger side of the engine block just under the ignition module you can see it from underside. The easiest way to see it and access it is to jack up the passenger side front wheel and take the wheel off there is a rubber flap in the wheel well you can push out of your way. I am warning you be very careful removing it mostly made of plastic I broke one off leaving most of the sensor in the engine block had to drill the rest of it out which was no fun not alot of room for you to work. Get yourself a bottle of PB Blaster and keep spraying it as your pulling out before you try pulling out the sensor try to get it free enough that you can spin it around. Hope this helps good luck it fits pretty tight!

Posted on Oct 30, 2009

Ad
ZJLimited
  • 17970 Answers

SOURCE: crankshaft position sensor location

1990 Chevrolet Cavalier 2.2L TBI 4cyl
The Crankshaft Position Sensor is located under hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block.

87c675c.jpg

Fig. 1: View of the CKP sensor-to-crankshaft reluctor relationship

Crankshaft Position (CKP) Sensor
A magnetic crankshaft sensor (Hall Effect switch) is used which is remotely mounted on the opposite side of the engine from the DIS/IC module. The sensor protrudes in to the engine block, within about 0.050 in. (1.27mm) of the crankshaft reluctor.

I really hope help you wuth this (rated this help). have a nice day, good luck.

Posted on Sep 25, 2009

Testimonial: "Awesome. Thanks."

  • 1 Answer

SOURCE: 02 chevy silverado crankshaft sensor location

my 94 chevy truck stalls even at highway speed ,it starts again but stalls after a few secs, finally it will run for awhile before it stalls again

Posted on Mar 18, 2010

roniecon
  • 6826 Answers

SOURCE: were is the crankshaft position sensor located on 2001 chevy mali

It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.

Posted on Mar 22, 2010

  • 1 Answer

SOURCE: Where is the crankshaft sensor located on a 2001

have you found out how to fix this problem? mine is doing the same thing now. we replaced the crankshaft sensor but now it is saying i have a misfire

Posted on Jun 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft sensor located on a 2002 Chevy StarCraft engine 5.0 ?


I looked at info for 02 chevy express van-5.0L. Is this a vehicle, I don't know about starcraft?
The crank sensor is down by the front of crankshaft on the vehicle. If this is a boat or something, I have no idea?

Feb 05, 2016 | Cars & Trucks

1 Answer

Crankshaft Position Sensor location


It should be right below the harmonic balancer or crankshaft pulley on the engine block

Aug 04, 2014 | 2009 Chevrolet Suburban

1 Answer

Trying to locate crank sensor.


Corvette didnt have a Crankshaft Position Sensor until 96

Sep 18, 2013 | 1993 Chevrolet Corvette

1 Answer

Crankshaft sensor location chevy traverse 09


I spent hours in engine and on the internet. I viewed 15 different sites with 15 different answers. Finally found it...The crankshaft position sensor on a 2009 Chevy Traverse (3.6 liter) is as follows: You need to jack up vehicle (or useramps) and climb under. You CANNOT access it from top (as many sites state). On the firewall (vehicle) side of motor, in the center, directly below the exhaust outlet, you will see a silver (aluminum) heat cover/plate. It is held on by 2 bolts. (one 15mm and one 10mm). The sensor is located benind this cover. Once you get this cover off, you will see two seperate sets of wires, wrapped in silver heat deflection tape. The set of wires that extends further to the left go to th CPS (sensor). I used a small extendable automotive mirror to see it. It is in a tight spot, but once you find it, it is easier to access than it looks!!! Took me about 30 minutes total to switch it out. Hope this helps !!! Good luck.

May 05, 2012 | 2009 Chevrolet Traverse

1 Answer

Location of crankshaft sensor for 2000 chevy silverado 6.0 vortec?


The crankshaft position sensor is located on the top rear center of the engine near the bell housing.
Hope this helps.

Nov 21, 2010 | 2000 Chevrolet Silverado 2500

1 Answer

Need to replace the crankshaft position sensor


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the serpentine drive belt from the crankshaft pulley.
  3. Raise and safely support the vehicle.
  4. Remove the right front wheel and tire assembly and the right inner fender access cover/splash shield.
  5. Using a 28mm socket, remove the crankshaft harmonic balancer retaining bolt.
  6. Remove the crankshaft balancer, using a puller if necessary.
  7. For 1992-99 vehicles, remove the CKP sensor shield. Fig. 1: If so equipped, remove the crankshaft position sensor shield 89634g95.gif

  8. Unplug the sensor electrical connector.
  9. For 1987-91 vehicles, perform the following:
    1. Remove the sensor and pedestal from the block face.
    2. Remove the sensor from the pedestal.
  10. For 1992-99 vehicles, remove the sensor from the block face. To install:
    1. For 1987-91 vehicles, perform the following:
    2. Loosely install the crankshaft sensor on the pedestal.
    3. Position the sensor, with the pedestal attached, on crankshaft sensor installation tool J 37089 or equivalent.
    4. Install the bolt to hold the pedestal to the block face, then tighten to 14-28 ft. lbs. (20-40 Nm). Fig. 2: Position the crankshaft sensor tool on the crankshaft 89634g76.gif
      Fig. 3: Insert the crankshaft sensor tool into the harmonic balancer 89634g75.gif

    5. Tighten the pedestal pinch bolt to 30-35 inch lbs. (3-4 Nm).
    6. Remove the special tool.
    7. Place the crankshaft sensor tool on the crankshaft balancer and turn. If any vane on the harmonic balancer touches the tool, replace the balancer.
  11. For 1992-99 vehicles, install the CKP sensor on the block.
    1. Install the retaining bolts and tighten to 14-28 ft. lbs. (20-40 Nm).
    2. Install the crankshaft position sensor shield.
    3. Attach the sensor electrical connector.
  12. Install the balancer on the crankshaft.
  13. Tighten the crankshaft bolt to 200-239 ft. lbs. (270-325 Nm) for 1987-91 vehicles. For 1992-99 vehicles, tighten to 110 ft. lbs. (150 Nm), plus an additional 76┬░rotation.
  14. Install the inner fender shield and the right tire and wheel assembly.
  15. Carefully lower the vehicle.
  16. Install the serpentine belt.
  17. Connect the negative battery cable.
prev.gif next.gif

Oct 29, 2010 | 1999 Oldsmobile 88

2 Answers

Were is the crankshaft position sensor located on 2001 chevy mali


It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.

Mar 22, 2010 | Chevrolet Malibu Cars & Trucks

1 Answer

Crankshaft position sensor location


1990 Chevrolet Cavalier 2.2L TBI 4cyl
The Crankshaft Position Sensor is located under hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block.

87c675c.jpg

Fig. 1: View of the CKP sensor-to-crankshaft reluctor relationship

Crankshaft Position (CKP) Sensor
A magnetic crankshaft sensor (Hall Effect switch) is used which is remotely mounted on the opposite side of the engine from the DIS/IC module. The sensor protrudes in to the engine block, within about 0.050 in. (1.27mm) of the crankshaft reluctor.

I really hope help you wuth this (rated this help). have a nice day, good luck.

Sep 25, 2009 | 1990 Chevrolet Cavalier

1 Answer

Car just keep spinning


crankshaft sensor is located just above the crankshafy front dampener./ pulley

Apr 27, 2009 | 1997 Chevrolet Monte Carlo

Not finding what you are looking for?
1991 Chevrolet Corvette Logo

Related Topics:

462 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...