Question about 2001 Chevrolet Impala

1 Answer

How to bypass the passlock - 2001 Chevrolet Impala

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,184 Answers

Go to this link. You should find what you are looking for.

http://vatspasslockpasskeysecurityhelp.yolasite.com/

Posted on Feb 14, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bypass passlock system


Passlock sensor Problem 2001 Chevy Suburban/Truck ...

? 8:04
www.youtube.com/watch?v=EVjU0fh5h5s
Jan 29, 2013 - Uploaded by nightbandit007 Passlock sensor issues with 2001 Chevy Suburban. This is not how to bypass the system completely or .

Sep 08, 2015 | 2002 Chevrolet TrailBlazer

1 Answer

Replaced ignition car wont start


Here is a link that can help you with the bypassing of your Passlock antitheft system. http://vatspasslockpasskeysecurityhelp.yolasite.com/

Mar 25, 2012 | 2000 Oldsmobile Alero

1 Answer

What is the passcode for the anti theft system


his vehicle has a the PASSLOCK II key
based engine disabling system.

You can attempt to put the key in the ignition,
turn it on to just before cranking and then leaving
it that way for 10 mins. After that,
some PASSLOCK systems will re learn the code
and allow for starting. But if not, the system
will either need to be seen by GM or, a bypass module
is required to circumvent.

If left unchecked, it will continue to lock down
the fuel injector rail, and you will need to tow
it in to GM for evaluation, and resetting anyway.

Bothersome, but can be fixed.

I suggest the PLJX bypass kit to get around
this issue. www.PASSLOCK2.com

This Passlock Bypass Module is designed to momentarilly
allow the engine to remote start by sending a proper
coded pulse to open the fuel rail passlock injector
cut off circuit.

The output from an alarm/remote starter
would then shut down the pulse, once it has detected
the engine has engaged, and preserve the integrity
of the passlock system.

That is it's designed purpose.

However, in your case, this input wire on the PLJX module,
instead of going to a momentary ground pulse from
an alarm/remote starter,
would go to a constant chassis ground, through
the bypass module, grounding out the PASSLOCK.
The PASSLOCK would then always be bypassed as long
as that wire is chassis grounded.

I can not speak about a damaged passlock system,
like if a thief has destroyed it, because I do not
get into this part of GM'S security application.
But as a happy coincidence to installing
after market remote starters, this does work on bypassing
passlock in most all GM vehicles we've run into,
including your year GM vehicle as well.

Also, this is a self learning, resistor sensing
and adjusting module. Once the VATS wires have been tapped,
you would press the program button to learn,
and it does. The car should then allow start
with any hardware store key.

It would on yours as well.

You might want a car alarm installer to do this
for you, the fair rate being around 50. to 75.
for labor.

Jan 26, 2011 | 1999 Chevrolet Malibu

1 Answer

What wire do I cut to bypass the passlock on my 2004 alero


You Cannot cut any wires to bypass on this system. The passlock security needs to see a valid key in order to have the PCM enable the fuel and Ignition. This system is complex and cannot be bypassed with the cutting of a wire.

Dec 20, 2010 | 2004 Oldsmobile Alero

1 Answer

Can you bypass the anti-theft system on these if so how


There is a thing called the Passlock system which is the anti-theft system. You can get a passlock bypass module really reasonable to use. It comes with instructions as well.

Dec 21, 2009 | 1994 Oldsmobile Cutlass Supreme

3 Answers

1999 won't start when security light is on.


If you would like to bypass the system I found this, Good luck and please rate your mechanics help.


GM Passlock I & II Information

Please study the following information carefully WHEN INSTALLING REMOTE START systems on a 1996 or later GM car or truck.
Introduced in 1996, GM has changed the VATS anti theft system to Pass-Lock system. This is a similar device to the VATS system, in that there is a resistor present during the start cycle. However, in the PASSLOCK system, the resistor has been placed inside the ignition switch, instead of the key. See the GM V.A.T.S page for more information.
To remotely start a car with this feature, you must bypass the PASSLOCK system. There are two methods of doing so.. The first, is to permanently bypass this system. This is the easiest method for accomplishing your task. The second way, is to temporarily bypass the PASSLOCK, by introducing relays into the system, which retain all of the features of the system, while allowing your remotes start module to bypass it automatically during a remote start cycle.
Vehicles effected
(1996 and newer): N & J body cars, such as
Pontiac Sunfire and GrandAm Passlock-1
Chevrolet Cavalier Passlock-1
Buick Skylark Passlock-1
Oldsmobile Achieva Passlock-1

1997 or newer
Chevrolet Malibu Passlock-II
Oldsmobile Cutlass Passlock-II

1998 or newer
All trucks , SUVs and Vans Passlock-II

It is important to pay special attention to the fact that there are many different ways of achieving the same goal. There are actually 2 different Passlock-II systems. On the next page, there are tests to establish which type of passlock-II your car has.

Relays shown are standard automotive 5 pin spdt relays, available from IEI.
A multi meter is required to measure the resistance values. Accuracy is important within 5%.

Once the value of the resistor is measured, a resistor of the same value +/-5% must be purchased (Radio Shack, for example). You can also use a Potentiometer (POT), which can be adjusted to the same value of the resistor in the ignition switch.

pslc1.gif Passlock-I bypass procedure....

1: Remove the top and bottom shrouds from the steering column.
2: Find the 3 wire ribbon cable, coming from the ignition switch, containing White, Black, Yellow (Sometimes White, Black, Black). These are THIN wires.
3: Locate the Black 6 position connector on the LEFT side of the steering column, right above the ignition switch position. There is a BLACK (Thin) wire in this connector, called "Bulb Test", which shows Ground with ignition in the Off position, OPEN in the "Run" position, and GROUND in the "Crank" position.
4: Turn the ignition switch to the "Run" position. Do not crank the car.
5: Cut the Thin Yellow wire and strip both ends.
6: Without cutting the Black wire, expose some of the copper.
7: Using the ohmmeter, measure from the Yellow wire (the end coming from the ignition switch), to the exposed Black wire and record the value. Measure more than once to assure you have the right value.
8: Acquire the same size resistor and 3 relays, and perform the connections shown in the diagram below.

pslk2.gif PASSLOCK-II bypass procedure

There are 2 types of Passlock-II systems. To determine which system you have, follow these instructions;

1: Locate two wires, which are THIN and are in the main ignition harness.. Orange/Black (or Black) and Yellow.
2: Cut the Yellow wire, and strip back some of the insulation from the Orange/Black (Or Black) wires.
3: Turn the ignition to the "Run" position ( don't crank the starter). Measure and record the value measured from the KEY SIDE of the Yellow wire, to the Black/Orange wire.
4: Turn the key to the "Crank" position and release. Now read the value again.
pslk3.gif5: If the value changed, follow "Method#1". If the value stayed the same, follow "Method#2".







These diagrams are from our friends at ALARMTEK AUTO ALARM

Sep 26, 2009 | 1999 Pontiac Grand Am GT

1 Answer

2004 pontiac Grand Am with security passlock starting problems


Unfortunately you are correct, this
vehicle has the PASSLOCK II key
based engine disabling system, and currently it
is engaged. The sensor does not recognize &
retain the passlock reader chip in your ignition
switch any longer.

A bypass is required to circumvent.
If left unchecked, it will lock down the fuel injector
rail (as it has now), and you will need to
tow it in to GM for evaluation, and resetting.
Eventuall, the 10 minute over ride will cease to
work and you will finally be forced to visit
a Pontiac/GM dealer.

But, if you want to just remove this system
from the equation entirelly,
I suggest the PLJX bypass kit to get around
this issue.

This Passlock Bypass Module is designed to momentarilly
allow the engine to remote start by sending a proper
coded pulse to open the fuel rail passlock injector
cut off circuit.

The output from an alarm/remote starter
would then shut down the pulse, once it has detected
the engine has engaged, and preserve the integrity
of the passlock system.

That is it's designed purpose.

However, in your case, this input wire on the PLJX module,
instead of going to a momentary ground pulse from
an alarm/remote starter,
would go to a constant chassis ground, through
the bypass module, grounding out the PASSLOCK.
The PASSLOCK would then always be bypassed as long
as that wire is chassis grounded.

I can not speak about a damaged passlock system,
like if a thief has destroyed it, because I do not
get into this part of GM'S security application.
Coincidence to installing
after market remote starters, this does work on bypassing
passlock in most all GM vehicles,
including your year GM vehicle as well.

Also, this is a self learning, resistor sensing
and adjusting module. Once the VATS wires have been tapped,
you would press the program button to learn,
and it does. The car should then allow start
with any hardware store key.

Sep 12, 2009 | 2004 Pontiac Grand Am

1 Answer

Ignition passlock sensor


Need a bit more information, Is the security light on, have you checked for spark and fuel pressure, just in case you did and know it is the passlock system then check this out, hopefully it will ansewer your problem, please rate your mechanics help.
have a great day.

GM Passlock I & II Information

Please study the following information carefully WHEN INSTALLING REMOTE START systems on a 1996 or later GM car or truck.
Introduced in 1996, GM has changed the VATS anti theft system to Pass-Lock system. This is a similar device to the VATS system, in that there is a resistor present during the start cycle. However, in the PASSLOCK system, the resistor has been placed inside the ignition switch, instead of the key. See the GM V.A.T.S page for more information.
To remotely start a car with this feature, you must bypass the PASSLOCK system. There are two methods of doing so.. The first, is to permanently bypass this system. This is the easiest method for accomplishing your task. The second way, is to temporarily bypass the PASSLOCK, by introducing relays into the system, which retain all of the features of the system, while allowing your remotes start module to bypass it automatically during a remote start cycle.
Vehicles effected
(1996 and newer): N & J body cars, such as
Pontiac Sunfire and GrandAm Passlock-1
Chevrolet Cavalier Passlock-1
Buick Skylark Passlock-1
Oldsmobile Achieva Passlock-1

1997 or newer
Chevrolet Malibu Passlock-II
Oldsmobile Cutlass Passlock-II

1998 or newer
All trucks , SUVs and Vans Passlock-II

It is important to pay special attention to the fact that there are many different ways of achieving the same goal. There are actually 2 different Passlock-II systems. On the next page, there are tests to establish which type of passlock-II your car has.

Relays shown are standard automotive 5 pin spdt relays, available from IEI.
A multi meter is required to measure the resistance values. Accuracy is important within 5%.

Once the value of the resistor is measured, a resistor of the same value +/-5% must be purchased (Radio Shack, for example). You can also use a Potentiometer (POT), which can be adjusted to the same value of the resistor in the ignition switch.

pslc1.gif Passlock-I bypass procedure....

1: Remove the top and bottom shrouds from the steering column.
2: Find the 3 wire ribbon cable, coming from the ignition switch, containing White, Black, Yellow (Sometimes White, Black, Black). These are THIN wires.
3: Locate the Black 6 position connector on the LEFT side of the steering column, right above the ignition switch position. There is a BLACK (Thin) wire in this connector, called "Bulb Test", which shows Ground with ignition in the Off position, OPEN in the "Run" position, and GROUND in the "Crank" position.
4: Turn the ignition switch to the "Run" position. Do not crank the car.
5: Cut the Thin Yellow wire and strip both ends.
6: Without cutting the Black wire, expose some of the copper.
7: Using the ohmmeter, measure from the Yellow wire (the end coming from the ignition switch), to the exposed Black wire and record the value. Measure more than once to assure you have the right value.
8: Acquire the same size resistor and 3 relays, and perform the connections shown in the diagram below.

pslk2.gif PASSLOCK-II bypass procedure

There are 2 types of Passlock-II systems. To determine which system you have, follow these instructions;

1: Locate two wires, which are THIN and are in the main ignition harness.. Orange/Black (or Black) and Yellow.
2: Cut the Yellow wire, and strip back some of the insulation from the Orange/Black (Or Black) wires.
3: Turn the ignition to the "Run" position ( don't crank the starter). Measure and record the value measured from the KEY SIDE of the Yellow wire, to the Black/Orange wire.
4: Turn the key to the "Crank" position and release. Now read the value again.
pslk3.gif5: If the value changed, follow "Method#1". If the value stayed the same, follow "Method#2".







These diagrams are from our friends at ALARMTEK AUTO ALARM

Feb 24, 2009 | 1998 Pontiac Sunfire

Not finding what you are looking for?
2001 Chevrolet Impala Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...