Question about 2008 Nissan Versa

Open Question

Replace door handle assy. on 2008 versa

I have ordered and received door handle assy and now need instructions on how to remove and install new one

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
pal03246
  • 726 Answers

SOURCE: 2008 nissan altima, can't open drivers door from

you need to remove the inside door panel to gain access to the guts of the door handle. its a pretty extensive repair for a novice.

Posted on May 31, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I install the exterior driver side door handle?


You will almost definitely have to remove the inner door trim etc to access the rods etc that work the lock.
Try youtube.

Feb 17, 2016 | 2008 Nissan Versa

1 Answer

How do I install the exterior front door handle?


Take out inner door handle bezel-1 philips screw. Then remove 2 large screws under inner door handle. The lower light lens can then be removed exposing 2 small philips screws. Remove those and take out light assy and unplug. Use a screwdriver to pry gently on window-lock control switch assy. Remove and unplug. Then gently pry inner door panel off. The inner door handle and cables can be moves by sliding plastic assy back and out. Then you can remove the plastic rainliner exposing the door handle assy. 2 10mm bolts hold it in. Theres also to rods to remove by releasing clips and sliding rods out.

Feb 11, 2015 | 2004 Mitsubishi Endeavor

1 Answer

Left front door handle


Busted off right...common problem in these...you'll need to get one at either the junk yard(cheap) or the dealer(expensive)..then you need to take the door panel off the inside of the door to get access to the inside of the handle...there will be two 10mm nuts you need to remove holding the door handle assy. in..remove them and replace with new one..assemble in reverse order

Jan 22, 2011 | 1995 GMC Safari

3 Answers

How to replace exterior door handle on 2007 Versa.


You need a Torx head screwdriver T25. Open the door and on the side of the door is a small black grommet, remove grommet, inside is the torx screw you need to loosen for the lock mechanism to move. you dont need to remove the screw just loosen enough to move the lock assembly around. Once loose enough, install the door handle and tighten lock assembly back and put grommet back.
Here is a picture if you need a bit of visual clues.
http://img266.imageshack.us/img266/1218/versadoorhandlefix.jpg
_69.jpg

Nov 04, 2010 | 2007 Nissan Versa 1.8 Sl Hatchback

1 Answer

I am trying to fix a door handle that will not open from outside


Turn the window handle to where you can see a small 1/2" slot rt at its base where it meets the panel.you'll notice a small brass v shaped clip,you'll need hooked pick or something simular to hook this clip and pull it out of its slot,this release's window crank handle. Once this is off the rest of panel is held on by plastic panel clips that pull loose by pulling panel outwards from door ,and also by a few various screws. once panel is off temp. slide window crank back on and crank window all the way up. You then should have clear view of outer door handle. Handle has two rods attached to it,one for lock assy., one for latch release.This is the one you'll be looking at.Most likely you will find rod has came loose due to broken retainer clip at handle,or casting on handle itself has broken off.If clip is broke you can buy new clip at dealer or at some autoparts outlets,replace and reattach rod(make sure rod locks into place).If handle casting is broke will need handle replaced.It is held in place by two 10mm bolts,two rods preeviously mentioned. If handle is body color matched will need color code(on door jam sticker)to order handle from dealer to match.Lock assy will need to be transfered to new handle,it is held in by two spring clips.You notice two holes one on each side of lock,you will need to push release clips inwards through each hole to release lock and slide it out.to install just push down into newhandlle until clips engage. Let me know if you run into problems. Good luck and if this was able to help you please leave me some positive feedback. Thanks and good luck, Joel

Oct 12, 2009 | Honda Civic Cars & Trucks

1 Answer

I need instruction on replacing the passenger side mirror on a 2008 chevrolet cobalt


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Sep 24, 2009 | 2008 Chevrolet Cobalt

1 Answer

How to replace a 2003 grand vitara's rear door handle


1. open the rear door
2. open the rear door sidings
3. try loosing the not of the handle
4. remove the steel wirings of the handle
5. install the new rear door handle

Jul 15, 2009 | 2003 Suzuki Vitara

1 Answer

How to replace a side mirror


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Jul 14, 2009 | 2008 Nissan Sentra

3 Answers

1997 buick park ave 4 door right front door handle won,t work from the outside


Order the exterior door handle AND the clip that attaches the rod to the exterior handle from your local dealership ( any part in the salvage yard will have at least as much wear as the one U are replacing ) Also order a can of touch up paint matching your car. After you have the parts and have painted the new exterior handle, roll down the window and remove the interior door panel. ( instructions have been posted at 'replace door lock buttom' ) Two nuts, one on each side, hold the broken handle in place and must be removed ( DON'T loose them ). Loosen the rod from the clip at the top to allow a bit more room, But take note on the way it is attached ( you will need to reattach the rod to new handle ) To install new mechanism put the new clip on the rod, carefully place the gasket and the new handle in place and install nuts to secure. Test the door handle and make sure it works. Reinstall interior door panel.

Jul 06, 2009 | 1997 Buick Park Avenue

1 Answer

Replace passenger side mirror on 2008 Impala


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Apr 28, 2009 | 2008 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...