Question about Honda Prelude

Open Question

CYLINDER HEAD BOLT TORQUE 2000 HONDA PRELUDE 2.2

WHAT IS THE TORQUE WITHOUT NEW HEAD BOLTS

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

martin538
  • 117 Answers

SOURCE: need head bolt torque settings for 200 landrover discovery 4.0 liter 241 cu.in.

Stage 1 20nm
Stage 2 +90 degrees
Stage 3 +90 degrees

Posted on Apr 13, 2009

  • 512 Answers

SOURCE: Head Bolt Torque for a 2000 Grand Cherokee Laredo 4.0L

the torque is a 4 step process

1 torque all bolts to 22 ft/lbs
2 torque all bolts to 45 ft/lbs
3 recheck all bolts to 45 ft/lbs
4 torque bolts 1 thru 10 to 110 ft/lbs
bolt 11 to 100 ft/lbs
bolts 12 thru 14 to 110 ft/lbs
bolt #1 is the fourth bolt from the front on the passenger side....#2 is the fourth bolt on the drivers side then you continue in a clockwise order

Posted on Jan 04, 2009

  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

outdoorsman5
  • 631 Answers

SOURCE: head bolt torque specs for 2000 dodge neon 2.0 SOHC

I have the specs and diagrams. If you want me to send them to you, give me your email address. Outdoorsman592003@yahoo.com

Posted on Sep 05, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What lbs do I tighten the head bolts to on my 1990 Honda prelude SI 2.1L DOHC and in what order do I tighten them?


Go inside the local Autozone and ask for the cylinder head torque specs. They will look it up and print it out for you. It will contain the torque specifications as well as the sequences. Happy torquing.

Mar 01, 2015 | 1990 Honda Prelude

1 Answer

2003 honda odyssey 3.5 head bolt torque spec


Apply new engine oil to the threads and flanges of the cylinder head bolts.

Tighten the cylinder head bolts sequentially in three steps.

NOTE: Perform each step twice.

1st step torque: 39 Nm (4.0 kgf-m, 29 ft. lbs.)
2nd step torque: 69 Nm (7.0 kgf-m, 51 ft. lbs.)
3rd step torque: 98.1 Nm (10.0 kgf-m, 72.3 ft. lbs.)

Feb 28, 2014 | 2000 Honda Odyssey

1 Answer

HEAD TORQUE AND SPECS FOR A 2001 HONDA ACCORD 2.3L


Tighten the cylinder head bolts. Tighten the cylinder head bolts is sequence to 29 Nm (3.0 kgf-m, 22 ft. lbs.). Use a beam-type torque wrench. When using a preset type torque wrench, be sure to tighten slowly and do not overtighten. If a bolt makes any noise while you are torquing it, loosen the bolt and retighten it. Make sure the threads are clean, new heads bolts are best.

10_29_2012_10_15_36_pm.gif

Oct 29, 2012 | 2001 Honda Accord

1 Answer

I NEED replace head gaske


Hi there:Removal and InstallationExcept Accord V-6


The cylinder head temperature must be below 100 degrees F (38 degrees C); allow the engine to cool several hours if the car has been recently driven. Turn the crankshaft pulley so that the number one piston is at Top Dead Center (TDC) of the compression stroke.

  1. Disconnect the battery ground cable.
  2. Drain the cooling system.
  3. Remove the air cleaner and intake duct assembly.
  4. Label and remove the brake booster, PCV and charcoal canister vacuum hoses from the intake manifold.
  5. Remove the engine ground cable from the cylinder head or valve cover.
  6. Relieve the fuel pressure using the proper procedure. Disconnect the fuel lines.
  7. Disconnect the accelerator cable at the throttle body or carburetor. On automatic transaxle vehicles, also disconnect the throttle control cable.
  8. Disconnect and tag all the wire harnesses and vacuum hoses from the cylinder head, intake manifold and throttle body/carburetor. Disconnect the spark plug wires, then position them aside.
  9. Disconnect the upper radiator hose. Remove the heater hoses from the cylinder head.
  10. If equipped, remove the cruise control actuator. Do not disconnect the cable; move the actuator out of the work area with the cable attached.
  11. Remove accessory drive belts.
  12. Disconnect the inlet hose from the power steering pump and plug the hose immediately to prevent fluid leakage. Remove the power steering pump from the cylinder head and position it aside.

When the power steering hose is disconnected, the fluid will flow out. Cover the alternator with a shop towel to prevent the fluid from leaking into it.

  1. If the alternator is mounted to the cylinder head, remove it.
  2. Remove the power steering and alternator brackets if they are mounted on the cylinder head.
  3. Remove the distributor. Be sure to scribe a line relating the position of the distributor to the engine for easy installation.
  4. If equipped, remove the cylinder sensor next to the distributor.
  5. Remove the valve cover.
  6. Remove the timing belt.

Do not crimp or bend the timing belt.

  1. Remove the exhaust header pipe nuts and the header pipe bracket (if equipped). Pull the pipe away from the exhaust manifold.
  2. If equipped, remove the EGR crossover and air suction pipes.
  3. On Accords through 1989 and Preludes through 1991, the cylinder head can be removed with the intake and exhaust manifolds either still attached or removed. On other models, the manifolds should be removed first.
  4. On some engines, it will be necessary to remove the camshaft holders, camshafts and rocker arms to access the cylinder head bolts. If so, refer to the proper procedures in this section.
  5. Remove the cylinder head bolts in sequence (take notice of any bolt holes occupied by longer bolts). Failure to follow this procedure may cause the head to warp.
    1. On 1984-89 Accords and 1984-91 Preludes, work from the ends toward the center. Loosen each bolt about 1 / 2 turn each time and make several passes to release the tension evenly.
    2. On 1990-95 Accords and 1992-95 Preludes, follow the loosening sequence shown in the illustrations. Loosen each bolt about 1/3 turn each time. Repeat the sequence until all bolts are loosened.

3_5_2012_9_19_50_pm.gif
Fig. 1: Bolt loosening sequence on 1990-93 Accords and 1992-95 Preludes with 2.2L engines

24. Remove the cylinder head. The head may resist removal, even with the bolts out. Tap the edge of the head with a plastic or rubber mallet; lift the head straight up to remove it.
  1. Remove the cylinder head gasket and clean the mating surfaces.
  1. If applicable, remove the intake and exhaust manifolds from the cylinder head.

To install:
  1. Install a new head gasket on the engine, making certain it is positioned correctly. The cylinder head dowel pins and the oil jet must be in place. Refer to the illustrations if necessary.
  2. Install the head. Lower it straight down onto the block, aligning it correctly.
  3. Apply clean engine oil to the bolt threads and the contact face of the bolt head. Install the head bolts finger-tight.
  4. On all models except 1988-89 DOHC Prelude and 1992-95 Preludes with 2.3L and VTEC engines, tighten the head bolts following sequence A. On 1988-89 DOHC Preludes, use sequence B. Use sequence C on 1992-95 Preludes with 2.3L and VTEC engines.
    1. On 1984-89 Accords and 1984-91 Preludes, tighten the bolts in two passes. The first pass should bring the bolts to about 22 ft. lbs. (30 Nm). On the second pass, tighten the bolts to their final torque of 49 ft. lbs. (68 Nm).
    2. On 1990-93 Accords, tighten the bolts to 29 ft. lbs. (40 Nm) on the first pass, 51 ft. lbs. (70 Nm) on the second pass, then tighten the bolts to their final torque of 78 ft. lbs. (108 Nm).
    3. On 1994-95 Accords and 1992-95 Preludes, the bolts are also tightened in three passes. Tighten the bolts to 29 ft. lbs. (40 Nm) on the first pass, 51 ft. lbs. (70 Nm) on the second pass, then tighten the bolts to their final torque of 72 ft. lbs. (100 Nm).
    .
3_5_2012_9_24_01_pm.jpg
Fig. Cylinder head bolt torque sequence B

3_5_2012_9_24_44_pm.jpg
Fig. Cylinder head bolt torque sequence B

3_5_2012_9_25_06_pm.jpg
Fig. Cylinder head bolt torque sequence C

  1. If applicable, assemble the intake and exhaust manifolds to the head. Use new gaskets.
  2. If applicable, install the cam, rockers and camshaft holders.
  3. If equipped, install the EGR crossover and air suction pipes.
  4. Connect the exhaust pipe to the manifold using new nuts.
  5. Install the timing belt.
  6. Install the valve cover.
  7. Install the cylinder sensor (if equipped) and the distributor.
  8. If applicable, install the alternator.
  9. Install the power steering pump, then connect the inlet hose to the pump.
  10. Install the accessory drive belts. Adjust the belt tensions.
  11. Install the heater hoses.
  12. Install the cruise control actuator if it was removed.
  13. Connect the spark plug wires. Connect all the wire harnesses and vacuum hoses to the cylinder head, intake manifold and throttle body/carburetor.
  14. Connect the throttle control cable and/or accelerator cable at the throttle body.
  15. Connect the fuel lines.
  16. Install the brake booster, PCV and charcoal canister vacuum hoses.
  17. Install the air cleaner and intake duct.
  18. Refill the engine coolant. It is recommended that the engine oil be changed whenever a cylinder head is removed.
  19. Connect the negative battery cable.
  20. Start the engine, allowing it to idle. Bleed the cooling system. Check the work area carefully for any signs of fluid leakage or any indication of the timing belt rubbing or slapping the covers

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.
Thank you for using FixYa.

Mar 05, 2012 | 1993 Honda Accord

2 Answers

Head torque specs for 92 honda accord with f22a1


Thanks for using FixYa.

To install:
  1. Install a new head gasket on the engine, making certain it is positioned correctly. The cylinder head dowel pins and the oil jet must be in place. Refer to the illustrations if necessary.
  2. Install the head. Lower it straight down onto the block, aligning it correctly.
  3. Apply clean engine oil to the bolt threads and the contact face of the bolt head. Install the head bolts finger-tight.
  4. On all models except 1988-89 DOHC Prelude and 1992-95 Preludes with 2.3L and VTEC engines, tighten the head bolts following sequence A. On 1988-89 DOHC Preludes, use sequence B. Use sequence C on 1992-95 Preludes with 2.3L and VTEC engines.
    1. On 1984-89 Accords and 1984-91 Preludes, tighten the bolts in two passes. The first pass should bring the bolts to about 22 ft. lbs. (30 Nm). On the second pass, tighten the bolts to their final torque of 49 ft. lbs. (68 Nm).
    2. On 1990-93 Accords, tighten the bolts to 29 ft. lbs. (40 Nm) on the first pass, 51 ft. lbs. (70 Nm) on the second pass, then tighten the bolts to their final torque of 78 ft. lbs. (108 Nm).
    3. On 1994-95 Accords and 1992-95 Preludes, the bolts are also tightened in three passes. Tighten the bolts to 29 ft. lbs. (40 Nm) on the first pass, 51 ft. lbs. (70 Nm) on the second pass, then tighten the bolts to their final torque of 72 ft. lbs. (100 Nm).

      0900c152800b80b4.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Fig. 9: Cylinder head bolt torque sequence A

      jturcotte_2331.gif

      Fig. Fig. 10: Cylinder head bolt torque sequence B


      0900c152800b80b6.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Fig. 11: Cylinder head bolt torque sequence C


  5. If applicable, assemble the intake and exhaust manifolds to the head. Use new gaskets.
  6. If applicable, install the cam, rockers and camshaft holders.
  7. If equipped, install the EGR crossover and air suction pipes.
  8. Connect the exhaust pipe to the manifold using new nuts.
  9. Install the timing belt.
  10. Install the valve cover.
  11. Install the cylinder sensor (if equipped) and the distributor.
  12. If applicable, install the alternator.
  13. Install the power steering pump, then connect the inlet hose to the pump.
  14. Install the accessory drive belts. Adjust the belt tensions.
  15. Install the heater hoses.
  16. Install the cruise control actuator if it was removed.
  17. Connect the spark plug wires. Connect all the wire harnesses and vacuum hoses to the cylinder head, intake manifold and throttle body/carburetor.
  18. Connect the throttle control cable and/or accelerator cable at the throttle body.
  19. Connect the fuel lines.
  20. Install the brake booster, PCV and charcoal canister vacuum hoses.
  21. Install the air cleaner and intake duct.
  22. Refill the engine coolant. It is recommended that the engine oil be changed whenever a cylinder head is removed.
  23. Connect the negative battery cable.
  24. Start the engine, allowing it to idle. Bleed the cooling system. Check the work area carefully for any signs of fluid leakage or any indication of the timing belt rubbing or slapping the covers.

Sep 25, 2011 | Honda Accord Cars & Trucks

1 Answer

99 Honda civic 1.6 engine torque specs and sequences for cylinder head


Tighten the cylinder head bolts to their final torque specification in two steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts.
  1. Step 1: Tighten each bolt to 22 ft. lbs. (30 Nm).
  2. Step 2: Tighten each bolt to 61 ft. lbs. (85 Nm).

zjlimited_1681.jpg

Fig. Cylinder head bolt loosening sequence - 1.6L (B16A2) engines (click image for zoom)

Hope helps.

Aug 05, 2011 | 1999 Honda Civic

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

2 Answers

I need lower manifold rocker and upper manifold torque instructions please help


Head Bolts
Torque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation.New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.
The Intake Bolt Torque 10 Foot pounds (Final torque)
Note:to torque bolts & nuts, start in center using crisscross pattern working outward

Dec 05, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Hi what is the head torque on a 2002 honda civic


Dont forget to apply clean engine oil to the threads of each bolt for proper torquing. Then finger tighten. Then

    1. Tighten the cylinder head bolts to their final torque specification in 4 steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts as follows: Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).
    1. Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).
    2. Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).
    3. Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).
    4. Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).


  • Mar 25, 2010 | 2002 Honda Civic

    2 Answers

    Angle Torque settings head bolts


    Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

    Jan 28, 2009 | 2000 Renault Sportwagon

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    253 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8140 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...