Question about 1995 GMC Sierra C1500

1 Answer

94 gmc truck breaks pulls to one side - 1995 GMC Sierra C1500

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If your brakes are pulling to one side if you replaced the calipers it good be your brake lines cheap fixi have a 95 replaced everything but it was the brake line

Posted on Feb 14, 2012

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 120 Answers

SOURCE: want to bleed breaks on

Always start with the closest to the master cylinder and then so on. Then go around again.

Posted on Sep 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What causes code 81 on 94 gmc serria replaced lock up sol shift sol an epc sol still reading code 81


Sounds like the wiring harness between the motor and trans is worn through and shorting out. Common GM high miler issue. The ground wire stretches and breaks, leaving the trans non-functional after awhile.

Jan 21, 2015 | GMC Cars & Trucks

2 Answers

Soft brake pedal on 94 gmc sierra


in late model GM and Ford cars with quick take-up master cylinders, the quick take-up valve takes about 15 seconds to reseat after the brake pedal has been depressed, so you should wait at least 20 seconds before you press the pedal while bleeding. If the pedal is pumped too quickly while manually bleeding the system, you may never get the pedal to firm up. On a side note, did you check the level in the master cylinder after every 2 or 3 bleedin procedures? you could have been pumping air right back in the lines if the reservoir runs dry during the bleeding process.

Dec 16, 2013 | Cars & Trucks

1 Answer

How to change a 2004 GMC envoy front light


Drivers side- stick your hand down by the alternator and over behind the headlight. You'll feel a 3" round rubber boot, just pull this off. Twist the bulb out and replace it.

Passenger side- remove the air cleaner top, at this point, you'll have a lot of room to remove the rubber boot and replace the bulb.

The other method is to remove the grill, but pulling on this can break or crack the grill easily, so I choose this way.

Feb 27, 2011 | 2004 GMC Envoy

1 Answer

Clicking sound from the dash from behind the blower motor in the vent on 94 GMC Sierra


I see this problem is listed as a 2000 GMC 1500, yet you discribe the problem as on a 1994 GMC. The two trucks are very different, if it's a '94, them there are relays mounted on the passengers side firewall under a plastic shield, these will make clicking noises. If it's a 2000, the most common cause for that type of noise is the heat shields on the exhaust manifolds . If the noise is only present after [and sometimes while ] the motor is running, that's the most likley the problem.

Feb 01, 2011 | 2000 GMC New Sierra 1500

1 Answer

Cant find 4 way hazard module 94 seirra


To find the FLASHER on 1994 GMC Truck C1500 1/2ton Sub 2WD 5.7L TBI 8cyl. the Flasher is located: Front seating area, driver side, under dash, driver side of steering column, mounted in relay bracket

Application: Hazard flasher


Turn SIgnal flasher is one independent unit.


Hope helps-

Sep 16, 2010 | 1994 GMC Sierra

1 Answer

My breaks are locked you only on the front right side. how can i fix this. is a 94 gmc jimmy


A locked up brake usually is from either a caliper Which I would replace anyway now and the flexible brake coming off the frame to the caliper

Sep 24, 2009 | 1998 GMC Jimmy

1 Answer

Cruise not working


If any break lights are on, thats probably your problem. When your press the brake the cruise cuts off. (All Vehicles I know of)

Apr 11, 2009 | 1994 GMC Sierra

Not finding what you are looking for?
1995 GMC Sierra C1500 Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...