Question about Cars & Trucks

Open Question

Fly wheel torque settings for a pegeot 307hdi as i am putting new clucth in a peguoet 307 hdi

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22095 Answers

SOURCE: need to know the torque settings

put some locktight on the flywheel bolts and make sure they are tight by using a impact gun or jam a screwdriver into ringear and a bellhousing bolt as fulcrum and then pull bolts up with a big snap on knuckle bar and go round twice 1/2 inch drive---clutch use a 3/8 socket set and dont over tighten go round at least 3 times and dont forget to put copper grease on the spigot shaft splines .And remember to top the gearbox oil up with EP90 ,and lightly grease the new rear end oil seal you have obviously changed .

Posted on Apr 05, 2009

  • 341 Answers

SOURCE: torque settings for pressure plate and fly wheel

the flywheel is 50 -60 ft.lbs....pressure plate is 15- 25 ft. lbs..

Posted on Nov 22, 2008

emissionwiz
  • 75235 Answers

SOURCE: peugeot 307 hdi 110bhp 2003 , horn wont work ,can

Disconnect the battery for 30 minutes, this will disarm the airbag system and then u can change the part.

Posted on Apr 21, 2009

  • 205 Answers

SOURCE: "when do i change the cam belt on a peugeot 307 sw diesel"

usually you should do it for peugeot diesel at 122000 miles along with water pump and the tensioner roller that runs under the cambelt too. But to be on the safe side do it at 100000 and save the fortune.
It took me (DIY job) about 6-8 hours as i wanted to save 450 pounds.

Posted on Sep 04, 2009

  • 205 Answers

SOURCE: injectors

Injectors from the same ccm engine are most probably sounds same but to be on the safe side check not only the shape but code on the top of injector too. Because they are piezo effect injectors and set by the manufacture for a specific pressure for specific engine codes.

Posted on Sep 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

307 hdi 2ltr estate keeps cutting out. garage shows faults fix all those and it all starts again every time revrting to acc pedal changed twice


I guess this must be "fly by wire" system, so test the part on the throttle that the gas pedal "speaks" to.

Jun 20, 2016 | Peugeot 307 Cars & Trucks

1 Answer

Torque settings 307 1.6 hdi sw injector


About 7 foot pounds or 94 inch pounds. Either is not very much.

Dec 21, 2014 | Cars & Trucks

1 Answer

307hdi 51regmaking noise grinding


If it makes the sound during idle and you have manual transmission, check the clutch plates, pressure plate and related bearings. If it happens when the car is moving, check driveshafts, wheel bearing and brake pads.

May 02, 2014 | 2001 Peugeot 307 2.0

1 Answer

Hi I have pegeot 307 hdi 1.4 on 54 plate. I have a problem with sunroof. It only goes up and down but not backward and forward. It also does not fully close down. When i move the knob to slide back it...


Ask a bodyshop man not a mechanic is the best advice i can give here ,yes its possible to repair them you will need special fiddly tools to do the job so bewst advice is to ask a local bodyshop to have a look for you

Nov 16, 2013 | Cars & Trucks

1 Answer

Peugeot 307 hdi 110. lights left on battery died, put a new battery in. car keeps turning but won't start. immobliser light stays on


the car is imobalised, try disconectint the earth from battery for 5 mins and reconect, car should start

Dec 12, 2012 | Cars & Trucks

1 Answer

How much gear box oil do i put in my pegeot 807 2.0 hdi auto box


if transmission is a manual M20 you have to remove battery and battery tray to see oil filler plug.

Nov 13, 2012 | Cars & Trucks

1 Answer

Torque settings for pressure plate and fly wheel


the flywheel is 50 -60 ft.lbs....pressure plate is 15- 25 ft. lbs..

Nov 22, 2008 | 1995 Mazda B-Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

320 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...