Question about 2008 Honda Pilot

Open Question

Where is bank 1 on 05 honda pilot 3.5 - 2008 Honda Pilot

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Were is.my o2.senor b2 s1 On.my 09 Honda pilot


Just follow the exhaust pipe...

There are two exhaust manifolds with catalytic converter, one on the front of the engine, and one on the back. Front manifold is "Bank 2", and rear is "Bank 1".

On each catalytic converter, there are two sensors, one on the top, and one on the bottom. Top sensor is "Sensor 1" and bottom is "Sensor 2".

Mike

Yes You CAN use cell phone headset with Cisco IP Phone

Apr 08, 2017 | Honda Cars & Trucks

1 Answer

How do i reset my manint req's light after an oil change on a 2003 Honda pilot


1- turn off the engine. 2- press and hold the select/Reset button on the instrument panel, then turn on the ignition switch ON (II) 3- Hold the button for approximately ten seconds until the indicator resets or go to Honda pilot 2003 owner's manual see page 69.

Mar 09, 2015 | 2003 Honda Pilot

1 Answer

HOW TO REPLACE BANK 2 OXYGEN SENSOR 2 ?


Bank 2 is the front head, right behind the radiator.

Jul 03, 2014 | 2005 Honda Pilot

1 Answer

Need 07 Pilot P0430 error code troubleshooting tips


code p430 catalyst system below threshold bank 2 that is the front bank O2 sensor located bottom of exhaust manifold which is the top sensor.

Dec 31, 2012 | 2007 Honda Pilot

1 Answer

Oxygen sensor is bad


This picture may give you some information when you repair.
http://chinasinoy.com/service/bank-1-location-84.html

Aug 08, 2012 | 2005 Honda Pilot

1 Answer

2007 Honda Pilot service code P2647 A rocker arm actuator control system stuck on (bank 1) what does tis mean


Could be a bad oil pressure sensor on bank one or low oil level ,or incorrect oil and filter.

Aug 13, 2011 | 2007 Honda Pilot

1 Answer

My 2007 honda pilot while running the vsa light come on and then the engine light come on and the lose power


My 2007 Honda pilot did the same thing. I took the above advice regarding the oil condition (mine was obviously poor, although I change it every 3 mos) and had it changed immediately. The engine light, VSA light, and the triangle with ! all cleared and the vehicle began to run properly again. No problems since. Thank you to Shawn Bruns!!

Mar 27, 2011 | 2005 Honda Pilot

2 Answers

Steps to reset 2007 honda pilot oil gauge


From page 232 in the 2007 Honda Pilot Owners Manual.

1. Turn the ignition ON.
2. Press the Select/Reset knob until the engine oil life indicator is displayed.
3. Press the Select/Reset knob for more than 10 seconds. The engine oil life and maintenance item code(s) will blink.
4. Press the Select/Reset knob for another 5 seconds. The maintenance item code(s) will disappear, and the engine oil life will reset to "100".

Feb 27, 2009 | 2007 Honda Pilot

1 Answer

Bank 1 show on my ob11 tester


check the camshaft position sensor wiring located near the left front corner of the black cover over the top of the engine, my wiring was worn in half and caused my pilot to not start

Jul 31, 2008 | 2004 Honda Pilot

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...