Question about Chrysler Cars & Trucks

Open Question

How to remove the back rear seat of a chrysler 300

How to remove the rear seats

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Rear seat removal 2000 merc Villager

We have a 1997 Mercury Villager. I don't know how different it is from ours. We cannot remove the back seat. We can remove the middle seat and slide the back seat forward. I hope this helps.

Posted on Jul 06, 2008

alicantecoli
  • 22095 Answers

SOURCE: Peugeot 406 SV rear seat removal

take it you have done it------- two brackets at front of seat

Posted on Nov 20, 2008

polarcycle
  • 1392 Answers

SOURCE: 2005 Jeep Grand Cherokee rear seat removal

For the seat bottom, you just need to pull it up. The seat backs would have to be unbolted.

Posted on Mar 06, 2009

smartr10U
  • 1305 Answers

SOURCE: remove rear seat impala2007

To remove the rear seat, pull up on the front of the seat bottom, it should be hooked in place by spring type clips. After you get the front edge up, pull out the seat. This should expose the bolts/screws that hold the seat back in. Look below and there should be a couple of screws holding the seatback to the car body. Remove these and then you can pull the seat back out of the car.
K

Posted on Aug 29, 2009

  • 185 Answers

SOURCE: remove rear seat lexus es300 2008

the bottom of the rear seat pulls straight up at the front and out. its pretty tight, you need to pull very firmly.

Posted on Oct 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel pump located on a 2007 Chrysler 300


It's in the gas tank. Check for access panel under rear seat. Follow proper procedure for pump removal/install.

Jan 27, 2016 | Chrysler Cars & Trucks

1 Answer

How to remove a rear seat of a 2007 Chrysler 300 SRT8


1- pull up on the front edge of the seat cushion to remove it; it is held in by spring loaded fasteners
2- if you also want to remove the rear backrests, you need to remove the smaller one first by folding it down and removing the two screws from the bracket and then it just slides off of a pin attaching it to the bigger seat back. the bigger section is removed last the same way.

Mar 26, 2013 | Cars & Trucks

1 Answer

2006 chrysler 300 front seat heaters


where the hell is the fuse does not have one in the fuse box

May 13, 2012 | 2006 Chrysler 300

1 Answer

Front seat removal pt cruiser


If you move the seats all the way back you should be able to get at the front two bolts on each seat. If you move the seats all the way forward you should be able to get at the rear two bolts on each seat. Once the bolts are removed unplug all the harness under the seats and remove the seats from the vehicle.

Mar 09, 2012 | 2002 Chrysler PT Cruiser

1 Answer

Driver seat removal 1993 lexus gs 300


put the seat in the full back position remove the two front bolts securing it to the floor, move it all the way forward now, remove the two rear bolts securing it to the floor now tip the seat back allowing it to rest on the back seat. make sure there is no additional wiring plugged in. use the recline function the make the seat flatter, now with two people roll the seat and remove throught the front door utilizing the rear for the helper

Feb 27, 2011 | Lexus GS 300 Cars & Trucks

1 Answer

Replacing brake light above trunk on 2006 chrysler


This is quite a process....

Removal
1) Disconnect and isolate the negative battery cable.
2) Remove the rear shelf trim panel.

3ca61c4.jpg
3) Disconnect the CHMSL electrical connector (1).

7bde5c5.jpg

4) Remove the two mounting fasteners (3) to the CHMSL (2).

6793725.jpg

Installation is opposite of removal.

Rear shelf trim panel

Removal

1) Disconnect and isolate the battery negative cable.
2) Remover the right and left lower and upper C-pillar trim.
3) Remove the nut that secures the center rear seat belt lower anchor to the stud on the floor panel and feed the seat belt webbing back through the opening in the top of the rear shelf panel trim (2) to the retractor.
4) Remove the push-pin fastener (1) that secures the trim (2) to the rear shelf panel.
5) Slide the trim forward to disengage the S-clip that secures the underside of the trim to the to the center of the shelf panel.
6) Remove the trim from the rear shelf panel.

24614b2.jpg

Installation

1) Position the trim (2) onto the rear shelf panel(3).
2) Slide the rear edge of the trim rearward to engage the lens bezel of the center high-mounted stop lamp and far enough to engage the S-clip that secures the underside of the trim to the center of the shelf panel.
3) Install the push-pin fastener (1) that secures the trim to the rear shelf panel.
4) Pull the center rear seat belt lower anchor and belt webbing from the retractor through the opening the the top of the rear shelf panel trim and back down to the stud on the floor panel.
5) Install and tighten the nut that secures the seat belt lower anchor to the stud on the floor panel. Tighten the nut to 34 N m (25 ft. lbs.).
6) Reinstall the right and left upper and lower C-pillar trim.
7) Connect the battery negative cable.

841a5de.jpg

C-pillar trim removal

1a140ec.jpg

5ad047d.jpg

b674bd4.jpg
cf360b2.jpg

cd4ac09.jpg
2e5b4da.jpg

Seat removal

d276bae.jpg
60b3895.jpg

469e099.jpg

087d2a6.jpg

3ad2dc9.jpg


a09baad.jpg
4981771.jpg


Hope this all gets it done for you........

Feb 23, 2010 | 2006 Chrysler 300

2 Answers

How do you remove the rear seat in a chrysler 300M


Grab the bottom seat cushion at the front of one side and pull it straight up then do the same on the other side. (you will have to pull up very hard) The bottom of the seat clips in. once you have the bottom out take the 2 bolts out of the seat belt fasteners that holds the bottom of the top seat cushion. Then pull straight up on the seat cushion to slide it off two tabs that hold the top.

Jan 31, 2010 | 1999 Chrysler 300M

1 Answer

The heated seats for the front driver and passenger don't work


yes maybe a fuse, also look under the seat and ensure the wire is connected they sometimes get caught when moving the seat back and forward and split against the metal seat base.

Jan 16, 2010 | 2007 Chrysler 300c AWD Sedan New Cars

2 Answers

My batteries dead and cant get in car to jump it security


Hi, you can go threw your fender wall by taking a few screws off and removing it. your batt should be sitting on top of your right side fender wall. you can run cables to the batt this way to charge it. you will have to remove the tire to access the fonder wall.

Jan 28, 2009 | 2005 Chrysler 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

364 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...