Question about Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: replacing front shocks
Jack up the front end and place on jack stands. Place jack stands on the frame behind the front wheels. Ensure stands are not in a place where they will slip and make sure vehicle is on an even surface as you do not want the vehicle to fall off of the stands, especially while you are under it. Remove tires once vehicle has been placed on the stands. Remove the top and bottom bolts from the long tubular shock. Then remove the bolts holding the coil shocks on. Because when doing this as there may be tension in the coil springs still. Replace the shocks and reinstall the bolts. This job is fairly simple but can be intimidating if you have never done it before. You will be amazed at how easy it actually is once you have done it. Just be sure to remember how everything came apart and you will be able to get everything back together just fine. You can use the jack to adjust the axle up or down to make getting the shocks out easier.
Posted on Nov 11, 2008
12 is a battery disconnect within the last 50 start cycles and 55 means the end of the diagnostic cycle. Basically the computer found nothing wrong. The 12 code may seem incorrect if you haven't disconnected the battery recently, but from my experience the 12 code shows up almost all the time regardless.
Posted on Dec 16, 2008
SOURCE: serpintine belt
This link will take you to a picture of the diagram. If the link doesn't work contact me and I can email you the picture directly.
Posted on Jan 10, 2009
This Info taken from Wikipedia, the free encyclopedia
Hopefully this will answer your question.
The redesigned WJ 1999 Grand Cherokee shared just 127 parts with its predecessor. The structure was stiffened by PorscheEngineering for sharper steering and lighter weight. The spare tire wasrelocated from the side of the cargo compartment to under the floor togreat relief of owners. The two heavy pushrod V8 engines were replaced by chrysler's first clean sheet V8 since the 60's (SOHC aluminium heads, plastic intake), Chrysler's then-new PowerTech. Although this engine produced less torquethan both previous V8s, it was lighter and got much better fuel economyand provided similar on road performance figures (the 23 gallon fueltank was replaced with one of a 20.5 gallon capacity). The Inline 6engine was also updated in 1999. 10 horsepower (7.5 kW) was added byredesigning the intake manifold. The manual transmission was dropped with this model.
While other Jeep vehicles used the Mopar 5 x 4.5 bolt circle, thiswas the first Jeep following the 1987 Chrysler buyout to receive awider bolt pattern — 5 x 5. The 5 x 5 bolt pattern (also 5 x 127 mm),although common to GM rear wheel drive vehicles and light dutytrucks/vans, has spread beyond its use with GM (and Ford with their 1973 to 1978 LTDs and Lincolns). Chrysler first used the 5 x 5 pattern on full-size half-ton Dodge Ram pickups and Dodge Ramcharger SUVs in 1986.
A notable feature available in this generation was the automatic four wheel drive option called Quadra-Drive II.With three viscous clutches, it was one of only a few four wheel drivesystems at the time with triple locking differentals, joining thecontemporary Mercedes Gelandewagen, Mercedes Unimog and Magna SteyrPinzgauer, and the only one of the four with fully automatic operation,although the axle differentials could not be manually locked like inthe other three vehicles.
The 45RFE and 545RFE automatic transmission in the WJ was notable. It included three planetary gearsets rather than the two normally used in a four-speed automatic. Thisgave it six theoretical speeds, and it would have been the firstsix-speed transmission ever produced in volume, but it was programmedto only use five of these ratios. Four were used for upshifts, with adifferent second gear for downshifts. Although five of the six ratioswere used, Chrysler decided to call it a "4-speed automatic". In 2001,the programming was changed to make use of all six ratios. Rather thanhave six forward gears, the transmission was programmed to act as afive-speed with the alternate second gear for downshifts. The RPM at70 miles per hour (110 km/h) on a 545RFE is 2000 rpm, 200 rpm less thanthe 45RFE programming. 1999 and 2000 model year WJ owners can havetheir 45RFE transmission's programming flashed to enable the extra gearas both transmissions are physically the same. The 42RE 4-speedautomatic remained the transmission for the Inline 6 engine. It was notchanged from the previous model Grand Cherokee's.
Posted on Feb 14, 2009
Tips for a great answer:
Feb 24, 2014 | 1995 Jeep Grand Cherokee
Sep 09, 2012 | 1995 Jeep Grand Cherokee
Jan 11, 2010 | 1997 Jeep Grand Cherokee
Dec 27, 2009 | 1999 Jeep Cherokee
Nov 14, 2009 | 1995 Jeep Grand Cherokee
Jul 07, 2009 | 1995 Jeep Grand Cherokee
Mar 05, 2009 | 1995 Jeep Grand Cherokee
Nov 04, 2008 | 1995 Jeep Cherokee
Nov 23, 2017 | Nissan Cars & Trucks
84 people viewed this question
Usually answered in minutes!