Question about 1997 Chevrolet Tahoe

1 Answer

Tahoe braek lights

When i press the breaks the lights dont come on if i press the hazzard switch the break lights come on what is the problem

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 341 Answers

Check the brake switch located under dash near top of brake pedal

Posted on Oct 23, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997blazer break lights, hazard lights and turn signal light dot work ,but third break light works


You MAY have a couple of problems here and I've experienced them all on my 2000, but first things first. Check your brake switch wiring harness next to the fender under the dash (where the wire is too short and may shortout). Make sure it's not burnt, or you'll be chasing this forever like I did. If it is, replace the pigtail up there. If that is ok, jiggle your hazzard light switch and see if they start working again. If they start working, replace your hazzard light switch. If it's not that, it's your multifunction switch. Your lower brake lights run through the multifunction switch.

This same problem has affected many people, you're not alone.

Mar 10, 2017 | 1997 Chevrolet Blazer

2 Answers

Replaced break switch,and breake light stays on


I seen this before and it was the daytime running lights that were the problem

Mar 11, 2015 | 2009 Chevrolet Tahoe

1 Answer

My 1994 pontaic grand am all of a sudden my dash lights dont turn on or hazzards or tail lights but blinkers and break lights work just fine any ideas?


Do the headlights still work? Double check all the fuses. The actual headlight switch could be bad. It's common for the multifunction switches to go bad.

Dec 11, 2014 | Cars & Trucks

1 Answer

Break light stays on in my 2002 chevy tahoe?


Check the brake light switch on the end of the steering column close to the firewall...

Feb 05, 2014 | 2002 Chevrolet Tahoe

1 Answer

Brake lights turn signal and hazzards


Turn signals are on fuse number one and brake lights are on fuse number 9. Both are in the fuse box under the dash or on the side of the dash. Both are 15amp.

Jun 22, 2013 | 1995 Ford Mustang

1 Answer

MY UPPER LED BREAK LIGHT WORKS NO LOWER BRAEK LIGHTS


Sounds like a problem with the turn signal switch. The third brake light bypasses that switch.

Dec 06, 2012 | 1997 Chevrolet Suburban

1 Answer

1993 GMC sierra 1500 replaced rear turn signal bulb and break light bulbs..still no break light and turn signal still flashing fast..no hazzard light on same side


the break switch is damaged replace it then the hazzad light and the break light will be ok .. and about the indicator light its circuit's capacitor or the resistor is damaged please check that and replace the same it will be ok

Aug 24, 2012 | Cars & Trucks

1 Answer

99 chevy tahoe, brake lights won't go on unless I press the petal all the way.


SOUNDS LIKE A SWITCH PROBLEM ITS UP HIGH ON BREAK PEDEL UNDER THE DASH BOARD TRY UNPLUGING WIRES AND CLEANING CONTACTS AND YOU COULD SRRAYING CONTACT CLEANER IN SWITCH AND PRESS PEDEL REPETIDLY THIS MAY CLEAN THE SWITCH THERE IS ALSO AN AJUESTMENT TURN TILL WHERE THE ROD ON THE SWITCH IS CLOSER TO THE BREAK PEDEL IF NONE OF THIS WORKS YOU PROBBLY NEED TO REPLACE IT

Oct 15, 2010 | 2003 Lincoln Navigator

2 Answers

Break light problem


If you have a test light, check the brake light switch (usually mounted at the top of the break pedal arm). The switch will have voltage on one wire....when the pedal is pressed, the switch closes the circuit and sends voltage to the other wire connected to the brake lights.

Jun 30, 2009 | 1998 Acura TL

Not finding what you are looking for?
1997 Chevrolet Tahoe Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...