Question about Honda XR 400R

Open Question

2000 honda xr 100 idles to fast and i cant get it to idle down

The barrel seems to come all the down ,i have the idle screw backed out i found a crack in the intake pipe thought it was sucking air there bought a new one but still idles to high i dont know maybe something wrong in carb it was new 3yrs ago

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
biigg53566
  • 88 Answers

SOURCE: high fast idle at start up.

On most newer cars there is a fast idle motor controlled by the computer that will hold the fast idle till the engine reaches a preset temp in the computer then the engine should drop down to the set idle according to specs for that car. If the oil pressure continues to stay low after the idle goes down you may need to replace the oil pressure sending unit or if worse case the oil pump.

Posted on Nov 18, 2008

Ad
Molson02536
  • 3854 Answers

SOURCE: How to I set idle speed?

Before performing any on-vehicle adjustments to fuel or ignition systems, ensure engine mechanical condition is okay. CAUTION: When battery is disconnected, vehicle computer and memory systems may lose memory data. Drive ability problems may exist until computer systems have completed a relearn cycle.
IDLE SPEED & MIXTURE
NOTE: Idle mixture is controlled by Powertrain Control Module (PCM). Adjustment is not possible. After replacement of Idle Air Control (IAC) valve, system must be cycled as identified for PCM to properly control idle speed. If idle speed is not okay after cycling system, problem is usually caused by a dirty throttle plate or vacuum leaks. Ensure all vacuum components are functioning properly.

IDLE SPEED (4-CYLINDER)
Turn ignition on with engine off for 10 seconds. Turn ignition off for 10 seconds. Start engine and idle for 30 seconds. Slowly vary engine speed between idle and 3500 RPM 5 times. Return engine to idle. PCM will now properly control idle speed. 2.2L (Cavalier & Sunfire) & 2.4L (Alero, Cavalier, Grand Am & Sunfire)  Good luck and hope this helps. If it still has the high idle problem, your going to have to buy a can  if not two cans ot THROTTLE BODY CLEANER NOT CARBURATOR CLEANER. Just follow the instruction on the can and try to get the Idle Air Control Valve cleaned also which is on the sdie of the throttle body so go to town when cleaning the throttle body and then do the Idle speed relearn again. The other thing to is since your doing house cleaning, buy a MAF sensor cleaner and spray down your MAF sensor and IAT sensor also, this will help with your fuell consumption. 

Good luck and keep me posted, be glad to help.

Posted on Jul 04, 2009

ZJLimited
  • 17970 Answers

SOURCE: I just brought a 1970

1970 Ford Truck F100 P/U
- 5.0L 2BL OHV 8cyl
- 6.4L 2BL OHV 8cyl

Posted on Nov 08, 2010

  • 21 Answers

SOURCE: ive rebuilt a holly 4

You have to have a carb base plate gasket. Mr gasket makes a decent product that i currently use on my 84 F150. remove your carb and inspect the base of it, remove any debris that may be causing it to not seal properly. good luck

Posted on Dec 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i set the idle on my 1991 Honda Lx so it will pass emissions


should be a idle screw on the throttle body. right next to the accelerator cable. also make sure your cable isn't pulled tight keeping the accelerator opened slightly for a high idle

Oct 15, 2014 | 1991 Honda Accord

1 Answer

I have a 1988 mighty max that I bought with a rod knock. I have tore the bottom apart and replaced the cranck shaft and bearings ( main and rod) now that it is back together I am having idle trouble. cold...


I found this on another website on about adjusting the carb, not sure if this is the cause without knowing more information but give it a shot. should only take you about 10 minutes. "set the lever on the second highest step of the fast idle cam. measure the primary valve to throttle bore clearance, manual trans .031 inch automatic trans .035 inch, if its off, adjust it with the fast idle adjusting screw if you turn the screw clockwise the fast idle rpm increases,if you turn the screw counterclockwise the fast idle rpm decreases." You also may want to recheck the timing to make sure its exact.

Aug 26, 2013 | 1988 Mitsubishi Mighty Max

1 Answer

1998 Honda civic rising and falling idle


the timing could be off you may have to have it checked and fixed hope this helps

Dec 23, 2012 | 1998 Honda Civic

2 Answers

My 94 honda accord is idling up and down when in park or neutral whats the problem


hello, i just had the same problem. i have a 94 accord 4 cyl, and the rpm would sit at 500at normal temp. i cleaned the iacv the ficv. there is also a screw under the throttle body( i forgot what is is called, but you screw it back in), that seemed to help for my fluctuating idle problem. i recently changed my pcv valve and now my rpm sit at 1000. so i think that you need to change out your pcv valve. only 2.99 at autozone. hope you found this helpful

Jan 30, 2012 | 1994 Honda Accord

1 Answer

I have a 1987 Susuki Samurai, 1.3 engine. Cold start is idles at 2000 rpm up to 2200 rpm. Is this normal? Its seems a little fast. How do you adjust the cold fast idle speed? Thanks, Randy


Yeah it sounds kinda high. There is no adj except for the idle screw on the throttle, the computer does the rest, if it has one. If not, then you can adjust it some how. If carbureted, check for 2 little screws in the front, and check the choke, If throttle body, then just the idle screw, the idle should be around 1000. Hope this helps.

Jul 03, 2010 | 1987 Suzuki Samurai

1 Answer

Engine idle is not right. Seems to drop to fast


you may want to get your throttle position sensor checked out too.

May 17, 2010 | 2007 Saturn Aura XR Sedan

1 Answer

Wont idle down


your IAC idle air control sensor is probably gunked up and if it is so is your throttle body...also check all vacuum line for integrity..i found a bad hose going to my MAP sensor..both of this caused problems.
Clean the IAC with throttle body cleaner not carb cleaner, and dont clean the map sensor its contolled by air vacuum, just replace the hose if found cracked, if its bad you have to replace it it cant be adjusted.

May 09, 2010 | Nissan NX Cars & Trucks

1 Answer

Fast Idle above 2000 rpm during warmup & electrical issue


If it's not vacuum leaks, it will be you idle control sensor.

May 08, 2009 | 1993 Honda Civic 4 Door

1 Answer

Carb is acting weird cant seem to adjust


That is the choke adjustment,have you checked your timing on the motor and check and see if the vacum pod on the distributer is working. also check your vacum lines for any tears or cracks in them.

Mar 29, 2009 | 1984 Ford F 150

1 Answer

1985 Toyota Pickup -- Idles Too Fast


Sounds like both need the chocks ajusted or there sticking.

Feb 08, 2009 | 1990 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...