Question about Chrysler Aspen

Open Question

2007 Chrysler Aspen: sunroof switch is blowing fuse, changing switch does not fix the problem

Sunroof opens on its own and won't close. Open a window and it won't close. Was told by dealer that the sunroof switch is blowing the fuse and needs to be replaced. Switch has been replaced before and did not fix problem.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Interior sunroof shade is stuck closed

a solution that i had is that if you can open your sunroof without it opening ur shade try that then fold the shade by pushing between or in the middle of it and popout the shade. this works but try not to push to hard or you can break the plastic runners on the side of the shade. check to see if nothing is in the way of the runners. then put back the back part first then slide it all the way to the back then, do the other part and clip them back together  (there might be a little metal piece that pushes your shades back so check that first to see if its there first)

Posted on May 06, 2009

  • 69 Answers

SOURCE: MY SUNROOF WONT CLOSE

Check the owner's manual. There should be a section showing how to manually close the sunroof. You will use an allen wrench to turn the gears manually, I just don't know exactly what size or where the hole is located. It is typically located right behind the sunroof with a plug covering the hole in the headliner.

Posted on May 27, 2009

polarcycle
  • 1392 Answers

SOURCE: sunroof will not close

If the motor is stuck, you can probably hold the switch to the forward position, and smack the roof. This may allow the motor to start working. I don't think there is any way to do it manually.

Posted on Jun 15, 2009

  • 3 Answers

SOURCE: 08 SRX Ultraview Sunroof hard to close

Try spraying silicone lubricant in the groove that the rear brackets slide in (from the mid section of the roof to the rear).

Posted on Nov 29, 2009

  • 1 Answer

SOURCE: Sunroof will not close

How to manually close a sunroof on a 94 lexus es300

Posted on Dec 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sunroof does not open. Fuse is ok and the shade operates normally.


Do you know how to do automotive electrical testing ?????? How to read a wiring diagrams ???? http://www.bbbind.com/free_tsb.html .Videos on youtube Ohms Law Tech Tip from L1 with Dave Hobbs Copy of Voltage Drop Essentials TST Motor Age The only way to find the problem , testing !

Sunroof Description and Operation (One Connector System)
Sunroof
This diagnostic procedure is to be used for the 1 connector Sunroof System that combines the sunroof control module with the sunroof motor/actuator.
The Sunroof System consists of the following components:
• BATT MAIN 2 Fuse 50 A
• Body control module (BCM)
• RAP relay
• S/Roof Fuse 20 A
• Sunroof module (includes sunroof motor/actuator)
• Sunroof switch
The Sunroof System is controlled by the sunroof switch and the sunroof motor/actuator assembly.
When the ignition is turned to RUN or ACCESSORY, or when the retained accessory power (RAP) system is active, the body control module (BCM) applies a ground to the RAP relay in the instrument panel (I/P) fuse block. This activates the RAP relay and allows battery positive voltage to be applied through the SUNROOF Fuse to the sunroof module. Ground for the sunroof module is supplied from G302.
The sunroof can be placed in 3 preset positions:
• Open
• Vent
• Closed
When the sunroof switch is placed in the OPEN position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof motor/actuator then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the full open position.
When the sunroof switch is placed in the VENT position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof module then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the VENT position.
When the sunroof switch is placed and held in the CLOSED position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch close signal circuit. The sunroof module then applies voltage to the sunroof motor close control circuit and applies a ground to the sunroof motor open circuit. The sunroof motor then closes the sunroof.
The sunroof can be placed in any preferred open position when:
• The sunroof is in the fully opened position by pressing and holding the sunroof switch in the CLOSE position until the panel has reached the desired position then release the CLOSE switch in order to stop the sunroof
• The sunroof is opening, it can be stopped by momentarily pressing either side of the switch.
The sunroof control module, sun roof actuator, and the sunroof motor are integral parts of the sunroof module assembly and are not service separately.

Your best bet , take it to a qualified repair shop or buick dealer .

Feb 10, 2017 | 2010 Buick LaCrosse CXS

1 Answer

2006 Chevy Envoy Denali moonroof stuck open manually close


You mean GMC not Chevy ! Chevy doesn't make the Envoy . There is no way to manually close the sunroof !
Power Sunroof Inoperative
If voltage is not measured on the sunroof switch open signal or sunroof switch close signal circuits, the fault could be in the retained accessory power (RAP) supply voltage circuit, battery positive voltage circuit, or sunroof motor ground circuit. If the sunroof motor is not being powered, neither will the sunroof switch signal circuits.

2

Attempt to operate the sunroof through its full range of functions in order to verify that the power sunroof inoperative fault is present.
Does the power sunroof system operate normally?
--
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
YES - Go to Step 3

3
Is the sunroof in the fully closed position?
--
YES - Go to Step 4
NO - Go to Step 7

4
  1. Disconnect the sunroof switch.
  2. Turn ON the ignition, with the engine OFF.
  3. Connect a 3-amp fused jumper wire to the low reference circuit of the sunroof switch harness connector.
  4. Connect the other end of the 3-amp fused jumper wire to the sunroof switch open signal circuit of the sunroof switch harness connector, for 3 seconds.
Did the sunroof open?
--
YES - Go to Step 17
NO - Go to Step 5

5

  1. Disconnect the 3-amp fused jumper wire.
  2. Measure the voltage from the sunroof switch open signal circuit of the sunroof switch harness connector to the low reference circuit of the sunroof switch harness connector.
Does the voltage measure near the specified value?
B+
YES - Go to Step 13
NO - Go to Step 6

6

Measure the voltage from the sunroof switch open signal circuit of the sunroof switch harness connector to a good ground.
Does the voltage measure near the specified value?
B+
YES - Go to Step 14
NO - Go to Step 10

7
  1. Disconnect the sunroof switch.
  2. Turn ON the ignition, with the engine OFF.
  3. Connect a 3-amp fused jumper wire to the low reference circuit of the sunroof switch harness connector.
  4. Connect the other end of the 3-amp fused jumper wire to the sunroof switch close signal circuit of the sunroof switch harness connector, for 3 seconds.
Did the sunroof close?
--
YES - Go to Step 17
NO - Go to Step 8

8

  1. Disconnect the 3-amp fused jumper wire.
  2. Measure the voltage from the sunroof switch close signal circuit of the sunroof switch harness connector to the low reference circuit of the sunroof switch harness connector.
Does the voltage measure near the specified value?
B+
YES - Go to Step 15
NO - Go to Step 9

9

Measure the voltage from the sunroof switch close signal circuit of the sunroof switch harness connector to a good ground.
Does the voltage measure near the specified value?
B+
Go to Step 14
Go to Step 10

10

  1. Disconnect the sunroof motor harness connector.
  2. Measure the voltage from the battery positive voltage circuit of the sunroof motor harness connector to a good ground.
Does the voltage measure near the specified value?
B+
Go to Step 11
Go to Step 19

11

Measure the voltage from the retained accessory power (RAP) supply voltage circuit of the sunroof motor harness connector to a good ground.
Does the voltage measure near the specified value?
B+
Go to Step 12
Go to Symptoms - Computer/Integrating Systems in Computer/Integrating Systems

12

  1. Turn OFF the ignition.
  2. Measure the resistance from the ground circuit of the sunroof motor harness connector to a good ground.
Does the resistance measure less than or equal to the specified value?
5 ohms
Go to Step 16
Go to Step 20

13

Test the sunroof switch close signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
--
Go to Step 23
Go to Step 18

14

Test the sunroof switch low reference circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
--
Go to Step 23
Go to Step 18

15

Test the sunroof switch open signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
--
Go to Step 23
Go to Step 18

16

Test the appropriate sunroof switch signal circuit for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
--
Go to Step 23
Go to Step 18

17

Inspect for poor connections at the harness connector of the sunroof switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
--
Go to Step 23
Go to Step 21

18

Inspect for poor connections at the harness connectors of the sunroof motor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
--
Go to Step 23
Go to Step 22

19

Repair the short to ground or open in the sunroof motor battery positive voltage circuit. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you complete the repair?
--
Go to Step 23
--

20

Repair the open in the sunroof motor ground circuit. Refer to Wiring Repairs and Connector Repairs in Wiring Systems.
Did you complete the repair?
--
Go to Step 23
--

21

Replace the sunroof switch. Refer to Sunroof Switch Replacement .
Did you complete the replacement?
--
Go to Step 23
--

22

Replace the sunroof motor. Refer to Control Module References in Computer/Integrating Systems.
Did you complete the replacement?
--
Go to Step 23
--

23

Operate the system in order to verify the repair.
Did you find and correct the condition?
--
System OK
Go to Step 2

Jul 31, 2016 | Cars & Trucks

1 Answer

2001 cadillac deville sunroof open and want close


Check the RAP fuse in the rear fuse box , this fuse powers the sunroof control module ! Fuse Block - Rear , Left rear of the passenger compartment, under the rear seat .
The sunroof module contains the logic for the opening and the closing of the sunroof. The sunroof motor assembly contains the reversible DC drive motor, the gear train, and the limit switch.
The sunroof module determines the sunroof motor direction based on inputs received from the overhead console sunroof switches. When the ignition switch is in the ON position or when retained accessory power (RAP) is active, voltage is applied to the sunroof module via the RAP relay. For a description and operation of the RAP system, refer to Retained Accessory Power (RAP) Description and Operation in Retained Accessory Power. The sunroof module controls the sunroof motor direction by changing the polarity of the applied voltage. The sunroof module remembers the sunroof position whenever the ignition switch is turned to the OFF position. The limit switch is used as an input to the sunroof module to indicate that the glass is fully closed, or in the comfort stop positions. The limit switch is grounded when the sunroof glass is in the fully closed or comfort stop positions, otherwise it is open.
The SLIDE CLOSE mode is initiated by moving and holding the sunroof slide switch (ROOF) forward. This applies a ground provided from the sunroof limit switch low reference circuit to the sunroof switch close vent signal input of the sunroof module. The sunroof module controls voltage to the control circuits of the sunroof motor. The sunroof motor will run until the limit switch contacts are closed. The closing of the limit switch will apply the sunroof limit switch low reference circuit to the sunroof limit switch soft stop signal circuit to the sunroof module, indicating the flush closed position has been reached. As the sunroof is approaching the close position the sunroof glass will force the wind deflector downward.
You need to have a factory scan tool hooked up an have it checked for DTC'S in the sunroof control module ! a code reader will not do this , a code reader will only check the engine codes for OBD 2 .
Important: The following must be completed before using the symptom tables.
  1. Perform Diagnostic System Check - Power Sunroof in order to verify that all of the following are true:
  2. ?€¢
    No DTCs are set.


    ?€¢
    The control modules can communicate via the serial data link.

  3. Review the system operation in order to familiarize yourself with the system functions. Refer to Sunroof Description and Operation
your better off taking to the dealer !

May 09, 2015 | 2001 Cadillac DeVille

1 Answer

2006 CHRYSLER PACIFICA SUNROOF PROBLEMS CLOSING SUNROOF BUT THE FUSE APPEARS FINE. HOW CAN I GET IT TO CLOSE?


spray crc55 or wd40 into the slides and work the switch until it begins to work, once functioning repeat with silicone spray

Mar 09, 2015 | 2006 Chrysler Pacifica

3 Answers

Sunroof won't close


see the diagram attached and fix it. God bless youaa64eb51-7e11-4e93-a5bc-68a552df4913.jpg3d325aa6-02b4-4a16-b487-b8a581cd3d55.jpg

Jul 15, 2013 | 2002 Toyota Camry

1 Answer

My sunroof won't close


Some sunroofs have a open switch like the drivers window. You push it and the window will open automaticly. The button on your sunroof could be jammed so even though you can close it as soon as you release it, it will auto open on it's own.

Sep 25, 2012 | 2003 Toyota Corolla

1 Answer

Sunroof won't close


Hey Paul, there are limit switches integrated into the motor on your sunroof, usually if it stops completely its because it detected a restriction, such as leaves, or dirt, if there are no visual sign then with the key on hold the switch to the full open position for 10-12 sec then hold it in the close position for the same, cycle the key and see if it reset. The motor can fail as well but it's not very common.. Do u hear any clicking from the motor area when this occurs, also check all fuses to be safe as well,..

Jun 09, 2012 | 2006 Lincoln Mark LT

1 Answer

Sunroof on 1998 chevy cavalier z24 won't close all the way


It can be faulty motor or loose wiring issue or faulty /weak sunroof controlling switch or there is some blockage for sunroof to come down to close or sunroof out of its track the headliner is out of its way.There re many possibilities.All this basics needs to be checked.For further troubleshooting,go through this help link:----
Click the link mentioned below:------
How to Manually Close the Sunroof ? http://howtobyme.blogspot.in/2012/05/how-to-manually-close-sunroof-on-2001.html

-------------
Sunroof Stuck open? http://howtobyme.blogspot.in/2012/05/2001-lexus-is300-sunroof-stuck-open.html

----------
How to manually close Sunroof on Navigator? http://technoanswers.blogspot.com/2012/01/how-to-manually-close-sunroof-on-2000.html

----------
This will help.
Thanks.

Jun 05, 2012 | Chevrolet Cavalier Cars & Trucks

3 Answers

Open sunroof that will not close.


you can open and close you sunroof "manually" remove the plastic cover next to your sunroof and dome light buttons (above your rearview mirror) there is an allen wrench stored inside... insert the wrench into the corresponding hole and you can close or open you sunroof by turning the wrench

Nov 29, 2008 | 2000 Volkswagen Jetta TDI

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...