Question about 1999 Chevrolet Tracker

Open Question

DASHBOARD CLUSTER WIRING DIAGRAM FOR 1999 CHEVROLET TRACKER

I replaced the heater core in my 1999 Chev Tracker & when I put everything back together, it wouldn't start. Any suggestions??? Thank You.

Posted by on

5 Suggested Answers

  • 98 Answers

SOURCE: how do i change spark plugs on a 2003 chevy tracker?

I don't know if your vehicle is a 4 cylinder or 6 cylinder. This will make a difference in the # of cylinders as well as the placement. If it is the 4 c ylinder when you open the hood it says at Autozone.com that the spark plugs are on the front of the motor lined up 1-4. If it is the 6 cylinder then you will have 3 at the front of the motor and 3 at the back of the motor. Regardless it is the same concept. I don't know for this particular vehicle, but it is possible you may have to remove a large plastic engine covering in order to access the spark plugs. What I recommend is to replace the spark plug wires at the same time as the plugs. For all my vehicles I use NGK plugs and NAPA auto parts has the best plug wires I have used - Belden Maxx. Prior to starting you will want to check the "GAP" on each new spark plug. Using a spark plug gap tool available at parts places for about $1. Take the new plug and the non-porcelin end (the end that has the arc) insert the arc into the gap tool at the lowest end and slide the plug around until you reach the corresponding "GAP". For this vehicle it should be .44" (I checked on Autozone's website but you may want to check to be sure. At some of the part's places they may tell you that you don't have to check the gap, but believe me you alway's should. I just did a car where they insisted that I didn't need to check the gap and each plug was not gapped properly. The Arc on the plug has to be specific for your vehicle or you will have too much spark or not enough. After gapping the new plugs you are ready to start. Somewhere on the side of the motor you should see either 4 or 6 wires/cables branching out to the cylinders. Starting with whichever you prefer (do only one at a time to avoid confusion) trace the wire/cable to the cylinder and where it goes to the cylinder a "boot" covers the spark plug. Twist the boot until it comes off . If you are going to replace the plug wires take that one off and match it up to your new set (They will be different lengths). You will need a ratchet and a spark plug socket (available at parts places) The spark plug socket has rubber on the inside to protect the porcelin of the spark plug, and to provide grip. You may or may not need a small extension. Place the spark plug socket over the end of the spark plug and apply pressure until the spark plug begins to loosen. You may have to apply quite a bit of pressure if they are in there tight. Once it is loosened take the old plug out, and place the new plug in the spark plug socket. Don't use the ratchet at this point, just begin to thread the plug in by hand once it is in there as much as you can get it, tighten it down with the ratchet making sure not to over-tighten. Do the other cylinders in the same manner.

Posted on Mar 04, 2009

ourhowse
  • 2007 Answers

SOURCE: 2001 chevrolet tracker engine cranks but won't start

You have wet ignition components. Get an air hose and blow dry everything you can get to. You may even have to let it sit to dry out.

Posted on Apr 29, 2009

  • 20 Answers

SOURCE: how to replace a right rear axle seal in a 2001

you must remove all brake parts then you get to the axle easy to do with the right tools

Posted on Jul 22, 2009

Molson02536
  • 3854 Answers

SOURCE: I need the wiring diagram for a 96 Geo Tracker

1996 Geo Tracker Car Radio Wiring Diagram
Car Radio Battery Constant 12v+ Wire: White
Car Radio Accessory Switched 12v+ Wire: White/Black
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Red/Yellow
Car Stereo Dimmer Wire: Red/Green
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): White
Left Front Speaker Negative Wire (-): Black/Blue
Right Front Speaker Positive Wire (+): Blue
Right Front Speaker Negative Wire (-): White/Red
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Light Green
Left Rear Speaker Negative Wire (-): Light Green/Black
Right Rear Speaker Positive Wire (+): Gray
Right Rear Speaker Negative Wire (-): Gray/Black

Posted on Nov 22, 2009

Dak408
  • 277 Answers

SOURCE: How do you replace the crankshaft sensor on a 2000

If you have doubts about doing this repair I suggest you let and Certified Mechanic (ASE) do the repairs its not and easy task



REMOVAL PROCEDURE

  1. Disconnect the electrical connector from the crankshaft position (CKP) sensor.
  2. Remove the transmission from the vehicle.
  3. Remove the flywheel or the flex plate from the crankshaft.
  4. Remove the 2 bolts (3) and the sensor wire harness clips or shield.
  5. Remove the bolt (4) securing the CKP sensor to the engine block (5).
  6. Remove the CKP sensor (1) and the wire harness (2) from the vehicle.
  7. Inspect the CKP sensor signal rotor for damaged or missing teeth through the CKP sensor opening.
  8. 0882f41.gif
INSTALLATION PROCEDURE

NOTE: Do not pinch or damage the CKP sensor wire harness between the engine block and transmission during the transmission installation. Observe that the CKP sensor wire harness remains properly located in the channel provided at the rear of the engine block during the installation.

  1. Lubricate the CKP sensor O-ring with clean engine oil.
  2. Install the CKP sensor (1) to the engine block (5)
  3. Secure the CKP sensor to the engine block with the bolt (4). Tighten Tighten the bolt to 6 N.m (54 lb in) .
  4. Secure the sensor wire harness to the engine block with the clips or the shield and the 2 bolts (3).
  5. Install the crankshaft flywheel or flex plate.
  6. Install the transmission.
  7. Connect the CKP sensor electrical connector.
Good luck

Posted on Oct 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed the heater core, took the dash apart to replace the core, put everything back together and it will not start


Something not plugged back in or loose connection? Heater core replacements are time consuming and a lot of electrical has to be disconnected to perform the procedure

Dec 06, 2015 | Cars & Trucks

1 Answer

How to replace heater core chevrolet silverado 2001 ?


You will need to take the dashboard apart and then take all of the heating duct off. Unhook the 2 hoses to the engine cooling system in the engine bay. Then take the duct apart to take the heater core out . After all that just take everything back together. It,s a big job for sure!!!

May 01, 2014 | 1999 Chevrolet C1500

1 Answer

Replace heater core in 2002 chev tracker


Changing the heater core on a '00 Tracker is moderately difficult. To do it right you must remove the entire dash pan (just like a Ford), but besides that it's easy. The problem with removing the dash pan is the you will probably never get all the rattling out after you reinstall in. As far as getting the core you local parts store should be able to get it for you. You can go to www.advanceautoparts.com or www.autozone.com and check on-line to make sure. If they can get it and you don't mind using used parts go to www.junkyarddog.com (it will link you national salvage yards) good luck.

Oct 23, 2012 | Cars & Trucks

1 Answer

Need to back flush heater core on 1999 dodge stratus where is hoses located


Regarding this types of problem,i suggest you to go through this help links.Click the link below to go through the procedure and troubleshoot the problem :----HOW TO REPLACE AN UPPER RADIATOR HOSE

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-upper-radiator-hose.html

-------------
HOW TO REPLACE A LOWER RADIATOR HOSEhttp://schematicsdiagram.blogspot.com/2011/07/how-to-replace-lower-radiator-hose.html
----------How to Flush Heater Core?http://schematicsdiagram.blogspot.com/2011/12/how-to-flush-heater-core.html
------------

For heater core replacing procedure. I suggest you to go through this related help links.Its all complete step by step procedure: ----How to replace heater core for All car models?

Click the link below: ---

http://technoanswers.blogspot.com/2011/11/how-to-replace-heater-core-for-all-car.html

--------------
How to Flush Heater Core?

http://schematicsdiagram.blogspot.com/2011/12/how-to-flush-heater-core.html

---------------
How to Remove Heater Core ?

http://howtobyme.blogspot.com/2011/12/how-to-remove-heater-core-on-2008-honda.html
Heater Core Replacement?

http://howtobyme.blogspot.com/2011/12/honda-heater-core-replacement.html

------------
To replace heater core?http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on.html------

How to replace heater core?http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on_10.html
How to replace heater core on Buick Regal?

http://howtobyme.blogspot.in/2012/02/how-to-replace-heater-core-on-buick.html
----------This will help.Thanks.

Feb 16, 2012 | 1999 Dodge Stratus

1 Answer

I need diagram to to change heater core in chev silverado


I really wouldn't recommend that you try to take on this project yourself. Mitchell sets the labor time at 6.3 to 7.4 hours depending on options in the vehicle. This application requires the dash to be disassembled and removed from the vehicle to access the HVAC assembly. For a DIYer it you could easily spend 2 or more days. Additionally GM states that it is necessary to disconnect the evaporator core lines in order to remove the heater core. This means evacuating and recharging the A/C system afterwards. I strongly recommend that you take this to a professional to have it done. If you still feel like you want to attempt it, make a comment and I'll get you some images, but once again, I wouldn't suggest anyone other than a professional undertake this job.

Nov 04, 2011 | 2000 Chevrolet Silverado 1500

1 Answer

Step by step instructions on how to replace heater core


Buy a chilton manual online. there is no way to walk you thru this. It will save you time and money in the future.

Jan 19, 2009 | 1999 Ford Taurus

2 Answers

Vehicle that parts will fit a 1999 Chev Tracker


no i used to own one,the 99 tracker was a test car so it has its own special parts

Jul 26, 2008 | 1999 Chevrolet Tracker

Not finding what you are looking for?
1999 Chevrolet Tracker Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63456 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...