Question about 1998 Nissan Sentra

Open Question

2005 nissan blend door actuator stays on the hot side

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2926 Answers

SOURCE: 2004 nissan xterra, lost heat

ledsled378_20.gif


It is most likely related the door blend motor or acutator motor.

Posted on Dec 18, 2010

Ad
  • 193 Answers

SOURCE: Can I replace my nissan 1991 240sx a/c blend door actuator with a 1995 nissan 240sx blend door actuator?

NissanPartsDeal.com can give you a breakdown on the part numbers. Look up the part for both years and see if they are the same.

Posted on Oct 16, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 nissan altima heat goes from hot to cold


More than likely you have a problem in the temperature control blend door and or actuator.

Oct 27, 2017 | Nissan Cars & Trucks

1 Answer

I have a 2005 Nissan murano the a/c compressor comes on and hot air comes out the vents. Please help


Your problem is most likely caused by a jammed AC/Heater temperature control blend door and or blend door electric actuator motor. The door is stuck in the heated air position and can't move to divert the air flow across the cold AC evaporator core. In most cars this problem requires the entire dash assembly be removed to replace the parts.

Jul 14, 2016 | 2005 Nissan Murano

1 Answer

My 2005 ford free star. When I turn on m heater it only blows heat on the right side and cold air on the right side


There is a module that controls hot/cold direction flow, which does go bad. It's called a Heater Blend Door Actuator, and It's a bear to replace it, but doable. Not too expensive to do it yourself, but you _do_ need to be sure you're buying the exact replacement. You're best bet is to remove it before buying the replacement. The photo of the replacement is all you need to see you're buying the right one. Ford used different models in the same vehicles.

http://www.rockauto.com/en/catalog/ford,2005,freestar,3.9l+v6,1430707,heat+&+air+conditioning,heater+blend+door+actuator,10721

Feb 21, 2015 | 2005 Ford Freestar

3 Answers

Driver side blowing hot air passenger side blowing cold air


I'm having the same problem except on mine it's the driver's side that's blowing cold. Do you have the pictures in a finer resolution? I can't make them out and when I zoom, they are too grainy. Does the replacement require removing the dashboard? What's the general cost of the acuators? Are they readily available at like NAPA or other parts stores?

Nov 26, 2011 | 2006 Kia Amanti

1 Answer

My 2004 Avalanche ' heating system will not heat. No matter what the setting it either blows no air or cold air and it is 25 degrees outside so this is a problem. The engine is up to temp and I have tried...


The most likely cause is a failed blend door actuator; however I recommend a little troubleshooting. First, can you hear a clicking sound behind the dash when you turn the setting to hot? If yes, it is certainly the actuator stripping its gears. If not, check to make sure the heater hoses are both hot as they connect to the heater core at the firewall (in the engine compartment). If one or both of the hoses do not get hot, there is a blockage caused either by an air bubble or a stuck water control valve in the heater hose. If the hoses are both hot, the indication is again the blend door actuator.

Below are instructions for replacing the actuator. Look at the diagrams carefully--the big arrows point to the front of the truck and the actuator is on the side of the heater box above the outlet duct that runs to the driver's side of the floor. Also, the actuator is expensive, so I recommend you make sure it's bad and shop around a bit to get a good price. To check out the actuator, first see if you can turn the blend door by hand. If you can't turn it, maybe it's jammed. Also, reconnect the actuator after removing it and see what it does when you turn the heater to hot.

Removal & Installation
  1. Remove the floor air outlet duct extension (1) from the floor duct (2).

    jturcotte_393.gif

Fig. Remove the floor air outlet duct extension (1) from the floor duct (2)


Disconnect the electrical connection at the blend door actuator (#10 in pic below). jturcotte_394.gif

Fig. Blend door actuator and related components


Remove the blend door actuator mounting screws from the HVAC module.


Remove the blend door actuator as an assembly with the actuator cam.
jturcotte_396.gif

Fig. Remove the blend door actuator mounting screws from the HVAC module



To install:

  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam

  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).

  3. Connect the electrical connection at the blend door actuator (10).
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).


Picture of actuator:


jturcotte_57.jpg

Dec 07, 2010 | 2004 Chevrolet Avalanche

2 Answers

AC blows hot air on the driver side and cold air on the passenger side


You may have a bad temperature door actuator motor on the drivers side. The actuator is what moves the temperature blend door and when it fails it usually moves the door all the way to the "hot" position. Sometimes if you shut the vehicle off for a bit then restart it the system will work fine for a while then the actuator will again swing the door all the way open or shut. I've replaced several of these actuators [both drivers side and passenger side] for similar problems.

Jul 08, 2010 | 2005 Chevrolet Silverado

1 Answer

Ac blowing hot air


the blend door actuator located on the air box (right hand side under dash) is prob. inop. worst case senerio the blend door its self is broken. I have replaced the actuator more than anything.

Sep 16, 2009 | 2005 Chevrolet Silverado

1 Answer

I have a 1995 oldsmobile. The passenger side blows hot, regardles


try disconnecting the battery to re sync the two temperature control blend doors, if that doesn't work u will need to replace the control head or the drivers side blend door actuator.

Jun 23, 2009 | 2005 Dodge Durango

2 Answers

Heat flowing on passenger side only


your actuatior foe the drivers blend door is stuck. try unhooking battery for a few minutes have both on heat and hook back up and start up. the actuators will run thru a learn mode and sometimes this will free up.if not you will need an actuator

Dec 09, 2008 | 2005 Chevrolet Silverado

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
1998 Nissan Sentra Logo

Related Topics:

276 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...