Question about 2005 Chrysler Pacifica

Open Question

How to replace front bumper cover on chrysler pacifica

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 50 Answers

SOURCE: How do you replace rear bumper cover on Chrysler

There are three screws in the wheel well on either side plus a few regular bolts on top. Just pull out from the wheel well and go around.

Posted on Jan 24, 2010

  • 6 Answers

SOURCE: how to replace the rear bumper cover on a Chrysler

1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Posted on Sep 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my TCM located in my 2004 Chrysler Pacifica all wheel drive


its located near the battery , generally inside front bumper driver side

May 25, 2017 | 2004 Chrysler Pacifica

1 Answer

Replaceing front bumper chrome trim


Put a couple lines of silicone calk on it and stick it on there

Aug 02, 2016 | 2007 Chrysler Pacifica

1 Answer

My front blower stopped working in my 2004 Chrysler Pacifica. Where is the blower motor located so I can replace it?


BLOWER MOTOR IS LOCATED PASSENGER SIDE UNDER DASH. MIGHT HAVE A THIN PLASTIC TRIM COVER OVER IT

Jun 24, 2015 | 2004 Chrysler Pacifica

1 Answer

How to replace front bumper cover



Instructions

Engage the emergency parking brake, to avoid causing the car to roll or move when removing the bumper.

Release the screws holding the wheel well liners in place with a screwdriver. This will expose the screws holding the bumper bolts. Release the bolts holding the bumper in place, using a wrench, and have a friend support it while it remains wired to the car.

Disconnect the wiring running to the bumper to separate the fog lights from the car. Pull out the light fixtures from the bumper cover.

Remove the grill in the bumper cover, taking out the screws holding it into the cover. This will allow you to separate the grill and the bumper cover.

Secure the grill and light fixtures into the new bumper cover, using the hardware you removed from the old cover.

Reconnect the necessary wiring. Support the bumper cover in front of your car or have your friend hold it in place again.

Secure the bumper cover using the retaining bolts you took out earlier. Tighten the bolts to hold the bumper cover securely against the car.

Replace the wheel well liners with the screws you took out.


Jul 07, 2012 | 2006 Chrysler Pacifica

1 Answer

I have a 04 Chrysler Pacifica. My lower bumper came off now I am left with no lower bumper plus the plastic part of the car it was attached to came off. My upper bumper is in tact. I am trying not to...


Used ones are 100 to150 there are two screws by the rear tail lights. Push pins across the bottom and a screw in the bottom of each wheel well. Open tailgate and pull up

Sep 23, 2011 | 2004 Chrysler Pacifica

1 Answer

Location of pcm on 2005 pacifica?


I have a 2004 Pacifica and mine is on the drivers side front, underneath between the bumper and the wheel splash guard. You will need to remove the splash guard ti access the PCM. Not very hard at all. Replacement time for a handy DIYer: about 1/2 hour. Good luck!!

May 12, 2010 | 2005 Chrysler Pacifica

1 Answer

How to replace the rear bumper cover on a Chrysler Pacifica


1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Feb 16, 2010 | 2006 Chrysler Pacifica

1 Answer

We want to Changs spark plugs, when we take intake off is there wires to that or does it lift off without problems.


We had the same random problem. Sometimes it would do it and sometimes it wouldn't. It's an easy fix. Have the throttle assembly cleaned. You can do it yourself. That's exactly what happened with our 2004 Pacifica. I took it to the Chrysler dealership and since we have an extended warranty (bumper to bumper) it was covered. It was an easy job though. It took them about 10 mins.

Jan 30, 2010 | 2005 Chrysler Pacifica

Not finding what you are looking for?
2005 Chrysler Pacifica Logo

Related Topics:

746 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...