Question about 2000 Ford Ranger SuperCab

Open Question

2001 ford ranger transmission linkage adjustment

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76846 Answers

SOURCE: 2001 ford ranger automatic transmission

I have no other suggestions except what I already asked in previous calcification

Posted on Aug 08, 2008

Ad
PyroPCMan
  • 405 Answers

SOURCE: 1991 Ford Ranger manual transmission remove

444a343.jpg

  1. Disconnect the negative battery cable.
  2. Remove the gearshift lever assembly from the control housing.
  3. Cover the opening in the control housing with a cloth to prevent dirt from falling into the unit.
  4. Raise the vehicle and support it safely.
  5. On 2WD vehicles, matchmark the driveshaft to the rear axle flange. Position a drain pan under the tailend of the transmission. Remove the driveshaft-to-rear axle flange fasteners and pull the driveshaft rearward to disconnect it from the transmission.
  6. Disconnect the clutch hydraulic line a the clutch housing. Plug the lines.
  7. Disconnect the speedometer from the transfer case/extension housing.
  8. Disconnect the starter motor, back-up lamp and, if equipped, neutral sensing switch harness connector.
  9. Place a wood block on a service jack and position the jack under the engine oil pan.
  10. On 4WD vehicles, remove the transfer case from the vehicle.
  11. Remove the starter motor.
  12. Position a transmission jack, under the transmission.
  13. Remove the transmission-to-engine retaining bolts and washers.
  14. Remove the nuts and bolts attaching the transmission mount and damper to the crossmember.
  15. Remove the nuts and bolts attaching the crossmember to the frame side rails and remove the crossmember.
  16. Lower the engine jack slightly to angle the transmission assembly. Work the clutch housing off the locating dowels and slide the clutch housing and the transmission rearward until the input shaft clears the clutch disc.
  17. Lower the transmission jack and remove the transmission from the vehicle.
To install:
  1. Check that the mating surfaces of the clutch housing, engine rear and dowel holes are free of burrs, dirt and paint.
  2. Place the transmission on the transmission jack. Position the transmission under the vehicle, then raise it into position. Align the input shaft splines with the clutch disc splines and work the transmission forward into the locating dowels.
  3. Install the transmission-to-engine retaining bolts and washers. Tighten the retaining bolts to specifications. Remove the transmission jack.
  4. Install the starter motor. Tighten the attaching nuts.
  5. Raise the engine and install the rear crossmember, insulator and damper and attaching nuts and bolts. Tighten and torque the bolts to specification.
  6. On 4WD vehicles, install the transfer case.
  7. On 2WD vehicles, insert the driveshaft into the transmission extension housing and install the center bearing attaching nuts, washers and lockwashers. Connect the driveshaft to the rear axle drive flange.
  8. Connect the starter motor, back-up lamp and, if equipped, neutral sensing switch connectors.
  9. Connect the hydraulic clutch line and bleed the system.
  10. Install the speedometer cable.
  11. Check and adjust the fluid level.
  12. Lower the vehicle.
  13. Install the gearshift lever assembly. Install the boot cover and bolts.
  14. Reconnect the negative battery cable.
  15. Check for proper shifting and operation of the transmission.
The above was pulled frrom:
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800391da

hope this helps

Posted on Jul 02, 2008

  • 99 Answers

SOURCE: Linkage for transmission

Why don't you start by getting the correct linkage. Maybe the tranny you replace is not exactly the same one. No difficult to replace, some of them have adjustments so maybe you might be able to get away with it, by adjusting it properly. Ensure the tranny is in the park position when adjusting, if properly adjusted, all the other gear shift should fall in place.

Posted on Nov 05, 2008

SOURCE: clutch not engaging

If there is no fluid in the clutch cylinder then check that part of the system for leaks and repair/replace the componant. If it is the cylinder and not the pipe work, then the rubber seals have worn to excass. You may beable to buy the seals to repair the cylinder but I fear if that is the case of a new cylinder.

Posted on Nov 28, 2008

  • 184 Answers

SOURCE: how do i ajust a ford mondeo gear linkage

if memory serves me right you cannot adjust the cables on these cars.

Posted on Sep 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to unstick an automatic transmission on a 2001 Ford Ranger


Safety lock malfunction? Could be bad electrical connections to the safety lock. Probably bad linkage adjustments, or bushings on the linkage, or shift lever pivot same issue.

Apr 14, 2015 | Ford Cars & Trucks

1 Answer

Why won't my 2001 Ford Expedition shift into park?


If you Expedition is anything like my '99 Ranger, you have to have your foot on the brake to get it into "PARK". If you are doing that, then you have a transmission shift linkage adjustment problem that can happen if you have had your transmission removed or replaced, in which case I would have the shop that did the work adjust that linkage...no charge.

Mar 03, 2015 | Ford Cars & Trucks

1 Answer

Ford ranger gear shift linkage


replace any worn bushes/parts /linkages and adjust the shifter position

Feb 14, 2014 | Cars & Trucks

1 Answer

1994 ford ranger manual transmission


check the fuse , also check make sure the over drive switch is good.

May 27, 2013 | 1994 Ford Ranger Supercab

1 Answer

1994 ford ranger wont go into overdrive


might be the linkage not letting it go all the way down. like a bind up

May 27, 2013 | Cars & Trucks

1 Answer

Gear linkage for 89 ford ranger where is it located


You mean the shift linkage? Its on the drivers side of the transmission, from the shifter forward to the transmission.

Mar 25, 2013 | 1989 Ford Ranger

1 Answer

2001 ford ranger shuts off when i put it into park


Sound lik a problem with the "neutral safety switch"; try to check and adjust it, generally is located on top transmission.

Hope helps.

Sep 19, 2011 | 2001 Ford Ranger Regular Cab

1 Answer

I just got a 1996 ford ranger and its all messed up HELP


this sounds like a simple adjustment of shift linkage i guess i should ask if its a automatic transmission if so this is a great place to start..have a great day

Apr 30, 2009 | 1996 Ford Ranger SuperCab

Not finding what you are looking for?
2000 Ford Ranger SuperCab Logo

Related Topics:

304 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...