Question about 2000 Mercury Mystique

1 Answer

How to replace front wheel bearings in a 2000 Mercury Mystique?

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

Travis, this Mystique has sealed wheel bearings, you do not pack them with grease. You cannot even access the bearing. If you are not familiar with a car, you do not know if you are giving correct directions or not.

Posted on Jun 21, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 94 Answers

SOURCE: How do I remove and replace front wheel bearing on

you need to take the tie rod off , the lower ball joint off , take the strut bolt out and remove the nut and washer off the cv axel then pull the whole hub Assembly off then the new bearing need to be pressed in , then reinstall everything not as hard as it sounds

Posted on Mar 09, 2009

  • 255 Answers

SOURCE: Wheel Bearings

Hi, Front or rear???

Posted on Aug 17, 2008

MrScary66613
  • 1990 Answers

SOURCE: 1999 mercury sable front wheel bearing

Not too bad. Just remove the Wheel and the Brake Calipers. Then remove the Dust Cap off the Center of the Rotor. Inside there is a Bolt with a Cotter Pin In it. Remove the Cotter Pin and the Bolt. The Rotor will now Slide off the Spindle, The Bearings are Loose and Probably inside the Rotor. Remove these Bearings and get a Tube of High Temp Grease. Put a Big gobb of grease in the Palm of your hand and Roll the Bearing around in your Hand. Be sure to use your Fingers on the Inside of the Bearings to get it in. The same Goes with New Bearings.

Posted on Jan 23, 2009

  • 1 Answer

SOURCE: mercury mystique starter location

its a 6 I beleive its a 2.5

Posted on Mar 24, 2009

reisdos
  • 1297 Answers

SOURCE: 1998 Mercury Mountaineer wheel bearing

2x2 = nothing special since they are old fashion tapered bearings

4x4 = nothing special again BUT the wheel bearing is part of the hub assembly!

Posted on May 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have a 1998 mercury mystique, it needs front wheel bearing replaced, is there a video out there that can help ?


You'll need special tools to re seat the new races in the hub. The old races can be pushed out with a brass drift and a hammer. Same for the seal.

Sep 12, 2016 | 1998 Mercury Mystique

1 Answer

Replace front wheel bearing on 2000 mercury mystique


you will need a bearing press to change bearing or you can buy it as a compleat assembly below is a download of directions

Sep 25, 2014 | Cars & Trucks

1 Answer

Replace front wheel baeringue


It is a press in bearing . You will need about $600 in tools to get her done

Jan 14, 2014 | 1995 Mercury Mystique

1 Answer

Left front wheel


You may have a defective wheel bearing, it is not safe to drive have a shop look at it right away.

Nov 30, 2012 | 1995 Mercury Mystique

1 Answer

What is the torque spec on front wheel bearing on 1999 mercury mystique?


you need to seat the bearings with ~ 60lbs of torque while spinning the rotor. Then back off the nut 1 flat ..

Aug 26, 2010 | 1999 Mercury Mystique

1 Answer

How do you remove the rear tires to change the brakes on a 2000 mercury mystique


Simply jack the rear of vehicle (use jack stands to hold vehicle in upright position), remove the lug nuts holding wheel on and slide the wheel off.

Jun 24, 2010 | 2000 Mercury Mystique

1 Answer

How do I remove and replace front wheel bearing on 1998 Mercury Mystique????


you need to take the tie rod off , the lower ball joint off , take the strut bolt out and remove the nut and washer off the cv axel then pull the whole hub Assembly off then the new bearing need to be pressed in , then reinstall everything not as hard as it sounds

Mar 09, 2009 | 1998 Mercury Mystique

1 Answer

Wheel Bearings


Hi, Front or rear???

Aug 02, 2008 | 1996 Mercury Mystique

Not finding what you are looking for?
2000 Mercury Mystique Logo

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

fordexpert

Level 3 Expert

5481 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...