Question about Daewoo Nubira

Open Question

How to replace the serpentine belt 2005 suzuki forenza

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

AUTOSOUNDINS
  • 232 Answers

SOURCE: I Need step by step

THE EASIEST WAY IS TO GO TO YOUR LOCAL AUTO RETAILER AND BUY THE REPAIR MANUAL FOR THAT VEHICLE. PAY A BODYSHOP FOR THE INSTRUCTION

Posted on Aug 04, 2008

boysor2933
  • 293 Answers

SOURCE: 2005 suzuki forenza My car will not start up.

Check if the kill switch is engaged. Check for faulty starter solenoid or disconnected solenoid wire. Check for defective ignition switch. Check for defective starter motor.

Posted on Aug 10, 2009

  • 5 Answers

SOURCE: i need a diagram of a 2004 suzuki forenza

That's easy, there are some pulleys with ridges to grip the underside of the belt, and some are smooth for the top side of the belt.
I can only assume your belt broke and fell off so you couldn't see how it was on prior. But either way you have limited length, and the last place you would be routing the belt is the tensioner, which you should have located first, so you can have a wrench handy to fit it.

Here's what you have:
Top left= alternator (small ridged)
top right = power steering (large ridged)
Bottom right = AC compressor (large ridged)
Bottom middle = Crank Pulley (large ridged)
In middle next to Power steering = Tensioner (small shiny smooth)

Remove the air cleaner housing (two bolts)
Start on left top side and loop belt (clockwise) across the alternator to the power steering down to AC (also clockwise from right to left) then over to crank pulley (from bottom clockwise around to top of pulley) to tensioner (smooth, belt is backwards on it) which will go back up to the alternator.

At the top middle there should be a sensor protruding from the timing cover that the belt passes under as it connects between the alternator and the power steering. And you won't easily be able to fit anything besides a box-end wrench on the tensioner, so you may need some kind of extension on the wrench to get good torque on it without hurting yourself.


Posted on Oct 28, 2009

  • 1596 Answers

SOURCE: My valve cover is leaking. Do I need any special

ANSWERS to Both is NO if you have Minimal Skills you can Do it Yourself

Posted on Nov 07, 2009

  • 2841 Answers

SOURCE: When should the timing belt be changed on a 2005

Replace at 60,000 miles.

Posted on Feb 10, 2010

Testimonial: "Very fast answer. Thanks for the information."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much will i pay to replace the timing belt in a 2005 suzuki forenza


Have to ask the repair shop of your choice

There is no standard price for any vehicle
repair & your asking people on the web from
all over the world with different currency

Jan 24, 2013 | 2005 Suzuki Forenza

1 Answer

I replaced the timing belt on a 05 suzuki forenza and not i cannot figure out which mark to use on the exhaust cam pulley


  • Hear are the timing marks fora a 2005 Suzuki Forenza 2.0

  • Crankshaft gear to the bottom of the rear timing belt cover ----


ironfist109_352.jpg


  • Camshaft gear to Camshaft cover ---

ironfist109_353.jpg


  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Oct 10, 2011 | 2005 Suzuki Forenza

1 Answer

How do you change a serpentine belt on a 2007 forenza suzuki


Hi, raise vehicle, support with safety latches/jackstands, remove splash guard from passenger front wheel well. Using a box-end 15mm wrench release tension from automatic tensioner. Noting belt routing, remove serpentine belt, replace with new one, reinstall splash guard.

Sep 01, 2010 | Suzuki Forenza Cars & Trucks

1 Answer

HOW TO INSTALL SERP BELT ON 07 SUZUKI FORENZA


Raise vehicle, support with safety latches/jackstands, remove splash guard from passenger front wheel well. Using a box-end 15mm wrench release tension from automatic tensioner. Noting belt routing, remove serpentine belt, replace with new one, reinstall splash guard.

Dec 30, 2009 | 2007 Suzuki Forenza Sedan

1 Answer

Need diagram for serpentine belt


2004 SUZUKI FORENZA - L4 2.0L 2000cc GAS FI N

Adjustment

The belt is automatically adjusted by the auto tensioner.


Drive Belt Routings

47cc840.jpg

Fig. Accessory drive belt routing-2.0L engine



Removal & Installation
  1. Remove the air filter housing assembly bolts and the air intake tube.
  2. Remove the air filter housing assembly from the vehicle.
  3. Use a wrench to turn the tensioner bolt clockwise, compressing the tensioner, and releasing the tension on the serpentine accessory drive belt.
  4. Remove the serpentine accessory drive belt.
To install:
  1. Use a wrench to turn the tensioner bolt clockwise, compressing the tensioner, and releasing the tension on the serpentine accessory drive belt.
  2. With the wrench in place on the tensioner bolt, loop the serpentine accessory drive belt loosely over the pulleys.
  3. Slip the belt over the tensioner.
  4. Remove the wrench from the tensioner bolt and the belt will tighten itself.
  5. Install the air filter housing assembly into the vehicle.
  6. Install the air intake tube and the air filter housing assembly bolts.
  7. Tighten the air filter housing assembly bolts to 53 inch lbs. and nm
I really hope helped with this. remember rated this help. Good luck.


Nov 12, 2009 | 2004 Suzuki Forenza

2 Answers

Strange sound


I have a 05 Forenza Wagon that made a clucking sound. I had to replace my auto tensioner when something went wrong with it and it broke. First I heard a high pitch sound as i was driving on the freeway and then the clucking. Finally, the auto tensioner got so loose it threw the serpentine belt off and shredded it.

May 19, 2008 | 2005 Suzuki Forenza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...