Question about 2005 Ford Excursion Limited

Open Question

My fisher minute mount 2 plow only angles right with all inputs. Push up or left it angles right.. drained fluid and cked filters all seems fine

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: i have a 2000 fisher

if it makes klic,klic,klic sound it may be the solenoid relay it cost about $30,try that

Posted on Jan 26, 2009

  • 51 Answers

SOURCE: minute mount 2 fisher plow stopped working up down

there could be a flat spot in the motor that runs the blade

Posted on Mar 03, 2009

  • 565 Answers

SOURCE: My fisher minute mount 2

the relay for it may be sticking . or the switch is. ive had to replace 4 relays this week for the same problem so start there. hope this helps

Posted on Feb 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a fisher minute mount 2 plow for some reason it only goes to the right now , not up or left , no matter what button I press on the control it goes right .


Start by plugging everything in and pop the cover off the control part on the plow and check for magnetism on all 3 solenoids when you hit the various buttons on your plow controller. The pull should be very strong and noticable...a weak magnetic pull is likely just residual magnetism on your screwdriver. In my case, the S3 solenoid wasn't firing and that causes exactly what you're describing.

If your S3 isn't firing you can test the wiring by moving the S3 hot wire to the S2 solenoid. If your wiring is good the plow will misbehave in an entirely different way. Also get out your ohm meter and test the S3, if its good you should get 7 ohms on it.

You need to use the guide from Fisher and be methodical about it. Start at the plow and work your way backwrds towards the truck.

Jan 27, 2016 | Cars & Trucks

1 Answer

I have a minute mount plow, when I try to use it only goes to left and right side but doesn't go up, when I try to lift the plow goes to the right. What can I do


2002 Fisher Minute Mount Inst-Act Wont Angle [Archive] - PlowSite ...

www.plowsite.com > ... > Truck & Equipment Repair

Nov 17, 2011 - 90 posts - ‎9 authors
My plow went up it was jerking and did it in steps , but , it got there . Now , it onlyjerks when i try to angle it right or left or up . I filled the fluid ... Drop it and if it doesn'traise you can just use a jack and shorten the transport chain to hold it. .... I do havecontinuity on the plow side for all 3 wires going to the plug . Hooking Up A Fisher Minute Mount 2 In Under 1 ...
54 posts
Feb 1, 2011
Plow Wont Angle
32 posts
Oct 19, 2010
What's wrong with my plow?
21 posts
Jan 9, 2003
Looking For Minute Mount Tips
57 posts
Feb 13, 2002
More results from www.plowsite.com

Ultramount Intermittent Angle Problem - Snow Plow Forum - L


Dec 27, 2015 | Cars & Trucks

2 Answers

I can hear my fisher plow motor but the plow will not lift or angle


There solinoids on pump. Check wiring and grounds. Make sure all small wires are intact and in good condition. But most likely there's a loose corroded or green wire causing issue

Jan 09, 2015 | Cars & Trucks

1 Answer

I have a fisher minute mount an older model with fixed controls. plow goes up and down but does not go left or right, sometimes with the control set for left or right it starts to go up ? where to sta


check the wiring connections on the plow solenoids to be sure they are correct, the second step is check the controller box, using a continuity check via multimeter set for DC voltage. I have an old western plow that had similar symptoms, and was the controller box.

Oct 19, 2014 | Cars & Trucks

2 Answers

When i try to lift or angle my plow all i get is a clicking sound when i push the lift button and when i let up on the button the moter on the hydrolic unit will click but will not move the plow. minute...


Not familiar with model, but valves click at the same time motor is suppose to run. Check power and ground to motor (or try running it with jumper cables, but don't be where plow can angle and squish you. If good power but won't spin, clean brushes/commutator/check bearings in motor.

Aug 15, 2014 | Cars & Trucks

1 Answer

Fisher minute mount plow


does the pressure release close to raise the plow?

Jan 05, 2014 | Dodge Cars & Trucks

1 Answer

Fisher minute mount 2 plow won't move.the motor runs but no plow movement? Is the pump bad?


You may have to bleed air out of the system to get it to work properly. Hope this helps.

Jan 02, 2014 | Cars & Trucks

1 Answer

Fisher minute mount goes up and left and locks up


check your connections, especially the main power plug in, i have used a small "c" clamp over the connection to aid in the same problem

Oct 29, 2009 | 1998 Chevrolet C1500

Not finding what you are looking for?
2005 Ford Excursion Limited Logo

Related Topics:

657 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...