Question about 1988 Ford Bronco II

Open Question

1988 ford bronco 2 how to replace front brakes

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
extreme7528
  • 108 Answers

SOURCE: how to replace the front brake hose on an 84 ford

should be a bolt where the hose enters the front caliper. just unhook and replace with new one. Be forewarned. When you change out the lines, you need to bleed the brakes as well.

Posted on Oct 07, 2009

Testimonial: "thank you for the simple yet helpful response to my question. You all have a wonderful day!"

Ad
chrischronic
  • 235 Answers

SOURCE: brake replacement

take the brake caliper off, this is the part that holds and moves the brake pads thare will be 2 bolts holding it on ,one on top one on bottom. after taking bolts loose you may half to pry the caliper up and off brake rotor. once this is done remove old pads and use a brake caliper piston retraction tool to push the piston back into the caliper. you can get this tool at your local parts store or use a C clamp with one of the old brake pads to push it back.install new brake pads and install caliper .after completion make sure you pump the brakes till you get a good pedal before moving vehicle

Posted on Dec 26, 2008

  • 1 Answer

SOURCE: 1988 ford bronco 2 break problems

i replaced my rear lines from the master cylinder to the adapter by the rear axle and that seamed to help me. you probably have a leak somewhere.

Posted on Aug 01, 2009

  • 31 Answers

SOURCE: hi, ive worked with bikes mainly and have replaced

Not much difference replacing the lines and fluids between disk and drum brakes. Huge difference when replaceing the pads. Never force the drum over the pads with a hammer etc. Make sure to take a picture of the assembly before taking it apart when not firmiliar with something. Adjust the brake tension through the site hole once the drum is over the pads.

When doing the disk brakes, make sure that you do not push in the caliper piston at it's edge. Use a C clamp placed dead center on the piston if required. Don't push it in any more than needed.

Posted on Nov 05, 2009

reisdos
  • 1297 Answers

SOURCE: How much should it cost to replace the timing

about $50 for the chain and another $10-$50 for extra parts like gaskets and broken bolts PLUS about 3hrs to 4hrs for labor

assuming you find a shop that charges less then $100/hr you should have it done under $500

Posted on Apr 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How does the axle come out in the front of a 1988 ford bronco 2 4WD automatic


No --if you could there would be nothing to stop he axle coming out on turns.

Dec 16, 2014 | 1988 Ford Bronco II

1 Answer

Location of oxygen sensor for 1988 ford bronco 2


The exhaust gas oxygen sensor is located on the manifold near the front of the engine, on the right hand side. It has a cable assembly attached to it.

Oct 17, 2010 | 1988 Ford Bronco II

1 Answer

Need firing order for 1988 ford bronco II


Hello :

Heres your firing order Sir. Hope this gets you back on the road. I thank you for using FixYa ,Please let me this Solved your Problem By Voting For my Solution.

Firing order 1-4-2-5-3-6 -------- front ' 1 2 3 ' of ' 'Distributor rotates clockwise vehicle ' 4 5 6 ' --------

Thanks Again From: d_hubbs

Sep 19, 2010 | 1988 Ford Bronco II

1 Answer

Firing order diagram for 88Ford Bronco II V6 2.9


For the 1988 Ford Bronco II 2.9L V6:

Firing Order:
1-4-2-5-3-6

Cylinders:
......(back)......
|..3..|......|..6..|
|..2..|......|..5..|
|..1..|......|..4..|
......(front)

Distributor:
....1.....4..(+)-screw
................
6......o.....2
................
(+)3.....5

Let me know if this helped or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Apr 05, 2010 | 1988 Ford Bronco II

1 Answer

Hi, ive worked with bikes mainly and have replaced drum and disc brakes on them. I am working with a ford bronco 2 1988 and would like to know how to replace the brakes on it. I know the front are disc and...


Not much difference replacing the lines and fluids between disk and drum brakes. Huge difference when replaceing the pads. Never force the drum over the pads with a hammer etc. Make sure to take a picture of the assembly before taking it apart when not firmiliar with something. Adjust the brake tension through the site hole once the drum is over the pads.

When doing the disk brakes, make sure that you do not push in the caliper piston at it's edge. Use a C clamp placed dead center on the piston if required. Don't push it in any more than needed.

Nov 05, 2009 | 1989 Ford Bronco II

2 Answers

1988 ford bronco 2 break problems


front or back is it leaking brake fluid

Mar 09, 2009 | 1988 Ford Bronco II

1 Answer

1988 f0rd bronco 2 brake lite on driver side not working


take the lens off and see if there is any corrosion that can sometimes cause a short. one of my reverse lights was corroded and i was having the same problem.

Feb 07, 2009 | 1988 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

348 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...