Question about 1999 Isuzu Rodeo

1 Answer

Replacing Cam Sensor in a 1999 Rodeo

I have a 1999 Isuzu Rodeo 4cyl and need to replace the cam sensor. How do I go about doing that? What holds the sensor in place, because they are no clips on the new or old one? It won't just pull out? Any help would be appreciated

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 275 Answers

It probably screws in can you put a wrench on it. if not it may have to be removed from the inside

Posted on Nov 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

WHERE DO I FIND THE CAM POSITION SENSOR ON A 1998 ISUZU AMIGO 4X4, 4 CYC?


all are near cam, so it can sense it.
all are 2 or 3 wires, not counting shield wire cover.
unless on pre DIS systems with distributor its in the old distributor base.
no engine stated, just 4cyl. (size matters )
my book shows DIS system
2.2L gas /petro not the 2.2 diesel
A new 2.2-liter X22SE engine built by Holden in Australian engine ! in USA car...


step 15,
3df8c2a8-ecf8-4bf8-9e78-8c6b9dffcd54.jpg26424456-dqx12sklk5srzazyyhn5uhav-3-2.jpg

Jan 02, 2017 | Isuzu Amigo Cars & Trucks

2 Answers

How do i replace the camshaft sensor on a 2004 rodeo


2004 had two engine but the early 2004 might have the 4 bangers , but the 4 banger dropped soon after July 2003 build day..

3.2 L 6VD1 V6 (gasoline)
3.5 L 6VE1W V6 (gasoline) a twin cam V6. !! unique.


in the next post i show all sensors. (most)

Aug 09, 2015 | 2004 Isuzu Rodeo

1 Answer

Where is the cam shaft position sensor on a 2001 izuzu rodeo 2.2. 4 cyl automatic


the sensor is under the timing belt cover at the top of the engine. If you are looking at the engine you'll see a black strip covering your spark plugs, your electrical connection on the camshaft position sensor is under there go ahead and disconnect the sensor. Next is the removal of the timing belt cover. You will need to take the bolts holding the cover in place they will hold it all the way down to the bottom of the engine. The bolt in the center top section is actually the bolt holding the sensor in place inside the engine so you will need to look and see how to maneuver the sensor out after the bolt is removed. Replace with new sensor and replace bolts. Plug electrical connector into the top of the sensor and replace spark plug cover. You are now done.

Sep 11, 2012 | 2001 Isuzu Rodeo

1 Answer

How to replace cam position sensor on a 2002 isuzu rodeo 2.2 engine


the sensor is under the timing belt cover at the top of the engine. If you are looking at the engine you'll see a black strip covering your spark plugs, your electrical connection on the camshaft position sensor is under there go ahead and disconnect the sensor. Next is the removal of the timing belt cover. You will need to take the bolts holding the cover in place they will hold it all the way down to the bottom of the engine. The bolt in the center top section is actually the bolt holding the sensor in place inside the engine so you will need to look and see how to maneuver the sensor out after the bolt is removed. Replace with new sensor and replace bolts. Plug electrical connector into the top of the sensor and replace spark plug cover. You are now done. have a good day !! 2.2 engine,

Feb 26, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

Checked fault memory code po342


if its V6 it is in rear left head next to inlet manifold
plug must face rear of vehicle

Apr 29, 2009 | 2004 Isuzu Rodeo

1 Answer

99 isuzu rodeo sensor problem


My abs sensor light comes on and off when I'm at at certain speed, I need help.

Mar 14, 2009 | 1999 Isuzu Rodeo

2 Answers

Is my '99 Isuzu Rodeo a single OR a dual cam? How can I find out?


HI.....
1999 Isuzo Rodeo. 3.5 L or 3.2L V6. Is a DOHC. Double over head cam.
and the engine 2.2 L 4cyl. SOHC, single over head cam.
The angibe 2.3 L 4cyl. Is DOHC.

OK.. I hope this help on your question.

Thank you for use fixya...

Aug 07, 2008 | 1999 Isuzu Rodeo

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...