Question about 1998 Porsche 911 Carrera

1 Answer

Program ignition key to central locking on porsche 996 1998

Cant lock car or put alarm on with key button but can start car , key button and batteries checked ok

Posted by on

  • philmacaw911 Oct 23, 2008

    cant lock car or put on alarm on with key button but key starts car,batteries checked ok how do you program it?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Well, you can sometime catch the code again. Pt the key in the ignition and turn till the dash light come on (dont Start) then press and the Lock button while keeping the Lock button Pressed and turn the dash light off and put the key with the lock button Press for 10 second afterwards. If not successful first time try again. This should do it.

Posted on Feb 22, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought a 1996 Subaru Impreza L 4dr 5speed AWD that runs and starts fine but when I was installing fog lights i noticed that there appears to be an alarm hooked up (it says "code alarm elite DM...


Battery Constant 12v+ Positive Wire (+): Black/Yellow
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness

Starter Positive Wire (+): Blue/Red
Starter Positive Wire Location: Ignition Switch Harness

Ignition Positive Wire (+): Red
Ignition Positive Wire Location: Ignition Switch Harness

Accessory Positive Wire (+): Red/Yellow
Accessory Positive Wire Location: Ignition Switch Harness

Parking Light Positive Wire (+): Red
Parking Light Positive Wire Location: Low In Drivers Kick Panel

Power Door Lock Negative Wire (-): Add Actuator. This vehicle uses a central door locking system. When connecting a keyless entry, you will need to add a door lock actuator and some units will also require (2) extra relays.
Power Door Lock Negative Wire Location: To Drivers Door Only

Power Door Unlock Negative Wire (-): Add Actuator. This vehicle uses a central door locking system. When connecting a keyless entry, you will need to add a door lock actuator and some units will also require (2) extra relays.
Power Door Unlock Negative Wire Location: To Drivers Door Only

Door Trigger Negative Wire (-): Red/White
Door Trigger Negative Wire Location: In Black Plug, Above Hood Release

Domelight Supervision Wire: Use Door Trigger, Requires Relay
Domelight Supervision Wire Location: N/A

Horn Negative Wire (-): Red/Green
Horn Negative Wire Location: At Steering Column Harness

Tachometer Wire Negative Wire (-): Black/Blue
Tachometer Wire Negative Wire Location: At ECM, Under Drivers Side Dash

Brake Light Positive Wire (+): White/Black
Brake Light Positive Wire Location: At Switch Above Brake Pedal

CODE ALARM SYSTEM

Used on:
Impreza 1996-2001
Legacy 1995-1999
Forester 1998-2000

codealarmremote2.jpgBattery GP-23A

Lock: Left button will lock all doors. Double chirp indicates locked.
Unlock: Right button will unlock driver's door only. Hold unlock button app 6 seconds, it will unlock all doors including rear gate. Single chirp indicated unlock.
If the car chirps or lights flash 4x the alarm was triggered.
Panic. Press both buttons to activate emergency honk and flashing lights.
Valet mode: With optional alarm onlyPress the red alarm button on the left of the steering wheel. The light will quickly double flash. To re-set back to normal mode, press the red alarm light button again

Battery failed and lights flashing?
Parking lights will flash when the vehicle's battery is disconnected and reconnected.
To stop lights from flashing, either:
Press remote transmitter "UNLOCK" button once OR turn the ignition switch to the "ON" position and press programming button for one second (see below).
The vehicle interior (courtesy) light and door open warning light (DOOR AJAR indicator) will then illuminate for 60 seconds when the ignition is turned off, or until the doors are locked with the remote transmitter. Yes, the dashboard instrument panel lights will flash when the parking lights flash.

Programming or Overriding the Alarm when you have lost the remote
Open driver's door.
Turn ignition key to 'On'
Press and *hold programming button* in (see diagram, button under dashboard)
After 15 seconds the the door locks will cycle 3 times. Do not release Programming button.
Press lock (left) button the remotes to be programmed. The door locks will cycle one time. Exit programming mode by releasing Programming button under dashboard and turning key to off.


codealarmremote1.jpgCode Alarm Programming Button is under dashboard on the kick panel by the driver's left knee, left of the steering column. If you can't find it, it might still be tucked up in the wiring harness higher up in that same general area. The botton is recessed in a plastic ring (see diagram).
This button must be pressed while programming remotes or if the battery was disconnected and the lights are flashing.

Jan 05, 2011 | Subaru Impreza Cars & Trucks

1 Answer

The central locking has stopped working on my 2000 Boxster s doors will not work and the horn bleeps twice


Have you tried starting car,some times on boxters low battery can give this problem
Open with key if alarm goes off insert key in ignition

Aug 31, 2010 | 2000 Porsche Boxster

1 Answer

Just bought a x reg ford puma but the key fob does not work, bought a new battery and fitted it, needs re-programming but don't know how to do it.


Telephone: Fax: VAT Registration No.:
Infrared remote control
NOTE: Infrared emitter can be seen at front edge of key.
System operation
Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds. Pressing key lock button once activates central locking and alarm. Pressing key lock button twice within 3 seconds activates double locking system.
Programming
When
Key batteries completely discharged. Key batteries not replaced within 15 seconds. Key added or replaced. System malfunction.
How
Obtain all keys fitted with remote control. Turn ignition switch to position I. Wait approximately 10 seconds. Ensure clock LED illuminates.
NOTE: LED illuminates for approximately 5 seconds.
Switch ignition OFF and remove key, while LED illuminated. Programming mode activated for approximately 20 seconds (LED illuminated). Proceed as follows: Point key at receiver (located near interior lamp). Press and hold unlock button Fig. 1 [1]. After approximately 1 second key LED will flash once [3]. Press lock button 3 times Fig. 1 [2]. Release unlock button Fig. 1 [1]. Continue to point key at receiver until LEDs in clock and key have flashed 5 times. Ensure LED remains illuminated. Repeat above procedure within 20 seconds to program remaining keys. To exit programming mode and extinguish clock LED: Switch ignition ON and OFF. Wait approximately 20 seconds.
NOTE: A maximum of 4 keys can be programmed. Fig. 1
Radio frequency remote control
System operation
Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds.


Pressing tailgate release button twice within 3 seconds unlocks the tailgate - if fitted. Pressing key lock button once activates central locking and alarm. Pressing key lock button twice within 3 seconds activates double locking system. Interior lamp illuminates when disarming system.
Programming
When
Key added or replaced. System malfunction.
How
Obtain all keys fitted with remote control. Fasten seat belts and close all doors. From position I, turn ignition switch as follows: To position II. To position I. To position II. To position I. To position II. To position I. Programming mode activated for approximately 20 seconds. LED or fog lamps ON warning lamp illuminates (some models) or the system will emit an acoustic signal to indicate start of programming mode. Proceed as follows: Type 1: Press and hold unlock button Fig. 1 [1]. Type 2: Press unlock button Fig. 2 [2]. Ensure clock LED or fog lamps ON warning lamp flashes (some models) or wait for acoustic signal (indicates correct programming). Wait 2 seconds. Repeat above procedure within 20 seconds to program remaining keys. To exit programming mode: Switch ignition ON. Wait 20 seconds.
NOTE: A maximum of 4 keys can be programmed.

Aug 25, 2010 | Ford Focus Cars & Trucks

1 Answer

1999 porsche 996 replaced key fob battery disconnected battery now trunk releses are locked and cant access battery.How do you open frt trunk manually


Assuming the car battery is ok (if not, buy a male to male cigarette lighter at the auto store and connect to another car until charged enough to unlock the doors...but don't try to crank the ignition!). The trunks won't open if the battery went dead with the alarm set because arming the alarm physically locks the releases.

Sounds like the key code is switched off because you replaced the key fob battery. Try unlocking the car manual with the key in the door lock. Then switch the ignition on to reactive the keyless entry. If this does not work, you might also try pressing the fob unlock button with the key in the door lock until the dash led flashes.

Jun 10, 2010 | 1999 Porsche 911 Carrera

1 Answer

How do I program a new OEM key for my 2001 Daewoo Leganza so it locks and unlocks the doors?


hi this is how you do it
first off make sure the alarm system is off then put the key to be programed into the ignition turn ignition on then off within 5 seconds this is then in program mode press the lock or unlock button 3 times within 20 seconds and then the central locking should start working indicating the remote is now programed...hope this helps please vote thanks

May 22, 2010 | 2001 Daewoo Leganza

2 Answers

2002 bmw 530i key does not (remotely) unlock doors or trunk but they work fine manually.


Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button. Press lock button briefly 3 times within 10 seconds keeping unlock button depressed. Release unlock button. Some models: LED flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously.

Mar 09, 2010 | 2002 BMW 5 Series

2 Answers

Remote central locking not working on Honda CRV 1999. central locking works with Key and the alarm and imobliser work form the remote.


Hi I wonder if you can advise me ,my central locking and alarm is very unreliable it keeps making a beep before the ignition goes on and clicking,it sometimes sets the alarm off,Ive had the AA round and theyve told me the car battery is dead,which I appreciate,but think the key hub central locking or alarm is running the battery low does the hand held button need a new battery,or can I take the fuse out for the central locking,dont want to pay 66 quid for a new battery if I can pay 2 quid for a new battery for the central locking button,or demobilize it

Aug 18, 2009 | 1999 Honda CR-V

1 Answer

1997 Porsche Carrera S --- Central Locking System Battery went dead while on travel and now the key fob for central locking is kaput! Is there a sequence to re-sync the fob to controller?


Hi,

Maybe you can try this procedure to resyn your key.
Initialization Procedure.

1. Open central locking system using the car key.
2. Get into the car and close all doors.
3. Using the car key, switch the ignition lock briefly to position "1" and then switch off again. (Please do this switching within 5 seconds or otherwise the system is not ready for initialization.
4. At the remote control key. Press the "OPEN" key (->) and keep holding.
5. When holding the "OPEN" key, press the "LOCK" button three time.
6. After pressing the "LOCK" button 3 times, release the "OPEN" button.
7. If the initialization process is sucessful, the door will lock and unlock immediately to confirm the process.

Jun 05, 2009 | 1997 Porsche 911

2 Answers

How To Program Porsche 911 Remote Keyless Alarm Key Fob


I have the same problem with my 1995 Porsche 911. I was quoted $260 for the key fob and $70 to program it. Sheesh!

Apr 07, 2009 | 1999 Porsche 911 Carrera

2 Answers

Key fob will not undo cetral locking or disable car alarm changed battery in key fob still having no luck any idea who can re code key fob to central locking and alarm?


If you don't have one that works for the vehicle now, you'll have to take it to your local dealer to have it programmed to the vehicle. Some will charge for this, some will do it at no charge.

If you do have a remote that is programmed and working for the vehicle, then the following steps will allow you to program another remote:

1. Enter vehicle and close all doors.

2. Put seatbelt on (or clip it into the buckle) to shut the warning buzzer off.

3. Put key in ignition, turn to run position but don't start it.

4. Press and hold the unlock button on the working key fob and hold for 4 seconds, then also press the panic button.

5. Release both buttons and you should hear a single chime to indicate it is in program mode. You have 30 seconds after the chime to program any additional remotes you want to program.

6. Press and release both the unlock and lock buttons simultaneously on the remote you are programming. You should hear another single chime.

7. Within 4 seconds after hearing the chime, press either lock or unlock button on remote that you are programming.

Oct 16, 2008 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
1998 Porsche 911 Carrera Logo

Related Topics:

3,494 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

570 Answers

yadayada
yadayada

Level 3 Expert

70347 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...