Question about 2006 Chrysler Sebring

1 Answer

How do you release pressure from the tensioner to remove the timing belt on a 2006 chrysler sebring?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 20 Answers

It should be on a spring loaded arm that applies tension from that to the belt. on the arm the is a spot where you can use a 3/8 inch socket wrench to reverse the tension and remove the belt.

Posted on Feb 11, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
jgwhomeequip
  • 1902 Answers

SOURCE: replacing headlight bulbs on a 2006 chrysler sebring

Behind the headlight you should see a eletrical wires running to the headlight section. There will be a 2 inch round plastic ring. You grap the back of the bulb and turn it to the right which will release the bulb and the socket. You pull out the bulb and replace it the same way. If this doesnt help then get back to me.

Posted on Feb 06, 2009

  • 1168 Answers

SOURCE: need serpentine belt routing for 2006 chrysler

Hello Damon104.
The best way to help you with this question is to give you this site.
Dayco belts offers this and covers most makes and models.

www.mvreader.com/multiview/dayco/index.php?bgInterchange=1&l=n

I hope your repair goes well for you.

Kl

Posted on Dec 17, 2009

  • 538 Answers

SOURCE: 2007 chrysler sebring serpentine belt diagram

Go to; daycoproducts.com, click cars and trucks, then go to serpentine belt. Then on the right side of the screen click on finding your vehicle. Then get the illistration number and click on illistrations, go to that number it should something 6-? or 7-?. It's a pretty good websight.

Posted on Jan 31, 2010

  • 1757 Answers

SOURCE: I need a timing belt diagram for a 2005 chrysler sebring

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

Again my apologies...
http://www.2carpros.com/car_repair_information/year/2005/make/chrysler/model/sebring/2005_chrysler_sebring_timing_belt_diagram_marks.htm

Posted on Mar 08, 2010

johnjohn2
  • 5763 Answers

SOURCE: were is the belt tensioner located on my 08

heres a diagram to show you the components, hope this helps,f87aa9c.png

Posted on Apr 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I relieve tenstion on 2005 Sebring belt tensioner?


Find the appropriate socket for the bolt along the tensioner pulley and attach it to the 3/8-inch ratchet handle. Place the socket head over the bolt on the tensioner pulley and push it in the direction indicated on the configuration chart on the hood of the vehicle to loosen the tension on the serpentine belt. Take the flat-head screwdriver to remove the serpentine belt from the tensioner pulley.

Nov 10, 2013 | 2005 Chrysler Sebring Conv

1 Answer

Picture of chrysler 2.4 belt tensioner


You Tube Video & Google

Internet Parts Suppliers

Mar 27, 2013 | 2006 Chrysler Sebring

1 Answer

How do i release the tension on a timing belt on a 2006 chrysler sbring


WHAT ENGINE? There are three different engines available for 2006 Chrysler Sebring and the timing belt set-ups are different.

Feb 11, 2012 | 2006 Chrysler Sebring

1 Answer

How to remove and replace serpentine belt on 2004 sebring with 2.4l dohc engine. are special tools needed, space seems really tight.


MY solution was to remove the rain shroud underneath the car, and work from beneath. Route the belt over all the pulleys, leaving the tensioner for LAST. With someone above releasing the tensioner with a serpentine belt tool, you can work the belt over the tensioner bit by bit. Make sure the belt is seated correctly before engaging the tensioner.

Nov 04, 2010 | 2004 Chrysler Sebring

1 Answer

Replacing a water pump on a 2004 pacifica


Release fuel pressure.Remove neg battery cable. Drain cooling system.Remove front cover.Remove timing belt. Remove water pump. Remove timing belt tensioner and slowly compress in vice. Install water pump then install tensioner and belt. timing belt runs water pump!

Sep 02, 2010 | 2005 Chrysler Pacifica

1 Answer

How to fix tension on the alternator 2006 Chrysler Sebring 4door sedan


Depending on what system they used in your vehicle this is either automatic by a spring loaded tensioner or there are adjustmenters attached to the Alternator, Power steering or AC compressor mounts. You can move these adjusters using a socket on the end of them. It's hard to explain them but typically to tighten the belt you turn the adjusting bolt clockwise and loosen it by turning it counter clockwise.

Jul 26, 2010 | 2006 Chrysler Sebring

1 Answer

Ho is the power steering belt on 2002 chrysler


Click on the following direct Link. It has the Belt Diagrams you will need, complete with Removal Diagrams and Directions. It also has numerous other helpful diagrams for use.

Standard Rules to Removal the Serpentine Belt with a Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

http://www.2carpros.com/car_repair_information/year/2002/make/chrysler/model/sebring/2002_chrysler_sebring_drive_belt_routing_diagram.htm

Mar 25, 2010 | 2002 Chrysler Sebring

1 Answer

1999 sebring serpintine belt installation


My sincere apologies for the severly delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, however I am answering it in case you still do.

Click on the following direct Link. It has several Diagrams for your Belt depending on your engine size and options (AC/No AC etc.) AND whether you have Tensioners OR Locking/Adjusting Bolts/Nuts.
IF APPLICABLE: These point out the direction of rotation for the Tensioner in order to loosen and reinstall the Belt.

IF APPLICABLE: These also point out where the Locking and Adjusting Bolts/Nuts are, to loosen the belt and remove; and reinstall the Belt and .

Standard Rules to Removal the Serpentine Belt with a Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating it\moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.


Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

http://www.2carpros.com/car_repair_information/year/1999/make/chrysler/model/sebring/1999_chrysler_sebring_drive_belt_routing_diagram.htm

Dec 28, 2009 | 1999 Chrysler Sebring

1 Answer

How can i get the idler tension to loosen up to cange my belt on my 2006 sebring


you loosen up center locking bolt bolt of tensioner pulley.there is a bolt next to tensioner pulley you turn the adjusting bolt to achieve the proper tension.

Dec 13, 2009 | 2006 Chrysler Sebring

Not finding what you are looking for?
2006 Chrysler Sebring Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...