Question about 2007 Toyota Aygo 1.0

Open Question

Toyota aygo ignition lock removal

How do i remove aygo ignition barrel

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 98 Answers

SOURCE: How to remove ignition cylinder from Toyota Camry 1993

Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!




  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

Posted on Nov 23, 2008

Ad
  • 1 Answer

SOURCE: Key will not turn ignition switch.

try sanding down the key alittle - saved me a fortune on my 96 civic

Posted on Apr 30, 2009

jmgldsmth
  • 1869 Answers

SOURCE: Removal of 1998 toyota cressida ignition key cylinder.

This car has drillable shear pin screws on the bottom of the lock yoke you must drill these out.
then release the clip to the cylinder. you must get a new set of break-off shear pin head screws from the dealer to finish the job.

Posted on May 19, 2009

  • 88 Answers

SOURCE: ignition lock cylinder removal without key

take the pannelling off around steering wheel inset a screw driver in key slot brekaway barrel to release steering lock pin then at other end of barrel take out scre and pull on wiring harness to expose a plastic barrel that will allow you to start car with a screw driver ect and you would not have steering lock as pin has been removed

Posted on Aug 07, 2009

  • 158 Answers

SOURCE: 1986 Toyota pickup. Parking brake cable snapped

best thing to do is have it done by a pro

Posted on Aug 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Put the wrong key in the ignition and now it's stuck. 2006 Toyota Camry


Good DIYer or vehicle locksmith should be able to free it. Option is to remove whole lock assembly and renew. You don't really want that. I don't know if lock barrel and key could be drilled out and just the barrel replaced, your local expert may know that.

Jul 02, 2015 | Cars & Trucks

1 Answer

Remove barrel from hiace ignition


barrel? the key tumbler , in he the igniton switch ? or the switch.?
no year, no class sizes or ton rating. wow., 1959 to now.
we don't have them here.
but on most cars this it it,
Generic:
  1. disconnect battery minus lug (defeat air bags , per FSM ways)
  2. off the plastics around IGN switch.
  3. some cars you most lower steering column a bit.
  4. remove the ignition switch assemble , anti-theft bolts (trash them)
  5. some cars need steering wheel off.
  6. remove switch from column, (plugs and what not)
  7. with a drift pin (lock smith type) drive the locking pin out of barrel.
  8. insert the key and remove the tumbler.
  9. or hand it to any locksmith and let him do it.
  10. The FSM may have a more simple way, so buy one at toyota.
fsm = factory service manual

Dec 11, 2014 | Toyota HiAce Cars & Trucks

1 Answer

Replace ignition barrel with a snapped metal intrument in it


you can try to remove said instrument with plyers, easiest way for me to fix a car like that is to replace the whole dang steering column. To replace the keyswitch only, check out this video, it applys to your car too! http://www.youtuberepeater.com/watch?v=oFsQhk-QQS8&name=toyota+corolla+ignition+lock+cylinder+and+key+switch+replacement

Dec 16, 2013 | 1996 Toyota 4Runner

1 Answer

Can you please tell how I can completely drain the coolant of my toyota aygo?


Some where along the bottom of the radiator theres a plastic plug some turn a lil to open others you got to remove completely... i do sugest flushing the engine and radiator both with lots and lots of hose water if you cant find the plug just take the hose off and hose it out

Oct 05, 2012 | 2010 Toyota Aygo 1.0

1 Answer

I have an Isuzu Rodeo and the key is stuck in the ignition any idea how to get it out? Year 2000


replace the whole ignition barrel with new key and get key programmed by dealer
can remove barrel and key by removing steering column covers turn ignition to on position and with small shank screw driver push in hole in outer top rear section of barrel assembly then pull out ignition lock barrel with key in it. fit new lock barrel and key, program new key into system and can get door lock barrels coded to suit new key or get code for old key and cut new key so it fits mechanical locks on the rest of the vehicle (just wont turn in ignition) 2 keys for vehicle.

Jun 13, 2010 | 2000 Isuzu Rodeo

1 Answer

What is the easiest way to remove a Toyota corolla ignition barrel please? 86 hatchback


the easiest way is to get someone else to do it but I imagine that you want to tackle the problem yourself. if it is on the steering column you have to remove the plastic cowling covering the shaft, this will expose the barrel which should just unbolt, I am only guessing as to where the ignition lock is, if it is in the dash you may have to remove items under the dash to expose the barrel to remove it

Jun 12, 2010 | 1986 Toyota Corolla 2 Door

1 Answer

Ignition barrel buggered


YOUR GOING TO HAVE TO STICK A SMALL CHISEL INTO THE KEY HOLE USED A SMALL HAMER TO KNOCK IT IN SOME, WITH VISE GRIP TURN TO THE ON POSITION, UNDER THE HOUSING WHERE THE LOCK CYLINDER GOS INTO, THERE WILL BE A LITTLE HOLE PUSH THAT LITTLE PIN IN THERE WITH A PICK HOOK AND SLIDE IGNITION LOCK OUT.

Nov 05, 2009 | 1993 Toyota Corolla

1 Answer

How to remove ignition barrel from 1997 toyota celica


Remove the plastic covers around the ignition switch, insert the key in the ignition and turn the key to ignition on position (just before start position) now locate the pin on the side of the ignition switch which is flush with the aluminium housing holding the barrel,the pin is about 3 mm in diameter.Gently press the pin inwards (which is spring loaded) with a sharp pointed object e.g small screwdriver and at the same time while holding the pin, pull on the ignition key as if you want to remove the key, and the barrel will slide out completely.

Regards
Phillip

Sep 17, 2009 | 1998 Toyota Celica

1 Answer

Ignition lock cylinder removal without key on 1989 toyota camry v6-automatic


take the pannelling off around steering wheel inset a screw driver in key slot brekaway barrel to release steering lock pin then at other end of barrel take out scre and pull on wiring harness to expose a plastic barrel that will allow you to start car with a screw driver ect and you would not have steering lock as pin has been removed

Jul 27, 2009 | 1989 Toyota Camry

Not finding what you are looking for?
2007 Toyota Aygo 1.0 Logo

Related Topics:

394 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...